軸密封填料 的英文怎麼說

中文拼音 [zhóumìfēngtiánliào]
軸密封填料 英文
shaft packing
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 密 : Ⅰ名詞1 （秘密） secret 2 [紡織] （密度） density 3 （姓氏） a surname Ⅱ形容詞1 （距離近; 空隙小）...
  • 填 : 動詞1. （墊平或塞滿） fill; stuff 2. （補足; 充滿） replenish; supplement; complement 3. （填寫） fill in; write
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  1. Because of the difference of production technology and operation condition, the jacket heating type divides electric bar heating, steam heating, conduction oil cyclic heating, and the shaft seal equipment divides stuffing seal and mechanical seal, and mixing type divides anchor type, paddle type, worm wheel type, pusher type and frame type

    由於用戶因生產工藝操作條件不盡相同，夾套加熱型式分為電熱棒加熱蒸汽加熱導熱油循環加熱，軸封裝置分為填料密封和機械密封，攪拌型式有錨式漿式蝸輪式推進式和框式。
  2. Superior finish ( 32 rms ) of packing chamber and stem ( 8 rms ) to assure long cycle life

    閥桿軸承保證同軸閥桿的旋轉，使得閥桿填料具有最大的密封效果。
  3. Stem bearing to assure concentric stem rotation, allowing stem packing to provide maximum sealing effectiveness

    閥桿軸承保證同軸閥桿的旋轉，使得閥桿填料具有最大的密封效果。
  4. Pragati plastics pvt ltd - our products and services are covered into the following ranges : bellows, bellows and seals as well as seals and / or bellows

    Pragati plastics pvt ltd是一家令客戶滿意的企業，該企業製造傑出的波紋管，波紋管，皮碗、漲圈、密封圈、軸環，鉛封、封口鉛（牙用）填料。
  5. Examine the seal condition of rotate axle regularly. replace or add graphite stuffing if there is mistake

    定期檢查三、四通溜子轉軸處的密封狀況，如發現密封問題請更換或填加石墨填料。
  6. Check that the hollow shaft and its seal are proper and that the packing gland should not compress too tightly on the packing set and the drip leakage is allowed

    檢查空心軸和軸密封程度是否適當，填料壓蓋不可將盤根壓得過緊，允許呈滴狀滲出。
  7. To ensure the charging pump working reliably, the following measures should be adopted : ( 1 ) adopting modified circular casing to reduce the radial force of the impeller and decrease the seal clearance ; ( 2 ) using radical ribs on impeller and helical sealing on shaft to realize minor pressure differential ; ( 3 ) using back pressure stuffing box to ensure sealing under small packing force ; ( 4 ) adopting self - lubricant flexible graphite stuffing for absorption of solids entering in the graphite in case of leaking

    為確保灌注泵可靠工作，提出改進措施： （ 1 ）採用改型環形泵體降低葉輪的徑向力，減小軸封間隙，抑制泄漏； （ 2 ）採用背葉片降低葉片根部壓頭，獲得微壓，使軸封兩端承受較小壓差； （ 3 ）採用螺旋密封降低軸封兩端壓差，在保持微壓的同時避免出現負壓，密封效果更好； （ 4 ）採用反壓式填料密封結構，在很小的壓緊力下，即可保證密封； （ 5 ）採用具有潤滑功效的柔性石墨填料，即使發生軸封泄漏，進入石墨內部的固相顆粒也將隨著石墨的消耗而被鉆井液吸收。
  8. Radial sealing can e mechanical seal to ensure without leaking within 8000 hours and also can be packing seal, so the maintenance is very convenient

    軸封可以選擇機械密封，保證8000小時無泄漏，也可以選擇填料密封，保養維護十分方便。
  9. The characteristics and requitements of the seal of vessel stem tube shaft is introduced and structural form and actual effect of packing seal of vessel stem tube shaft is analyzed, based on comparison, test and screening of seal packing materials, two braiding forms of synthetic fiber compounded packing arc adopted and are tested in real vessels, and good sealing effect is obtained

    摘要介紹了艦船艉軸密封的特點和要求，分析了艦船艉軸填料密封的結構形式和實效，在比較、試驗和篩選密封填料材料的基礎上，採用了兩種編織形式的合成纖維復合填料，並通過實船試驗，取得了良好的密封效果。
  10. Tail shaft packing

    尾軸密封填料
  11. Any problems relating to the design of dry or oil - filled electric motors immersed in the product have been overcome and the shaft passage and cable gland sealing systems in use today have proved highly satisfactory in a wide range of applications

    乾式或油浸式轉子設計的有關問題已被攻克，目前所使用的軸和電纜填料密封系統已被證明在各種工況下是十分滿意的。
分享友人
分享到 Line

分享到臉書