軸對稱彎曲 的英文怎麼說

中文拼音 [zhóuduìchènwānqū]
軸對稱彎曲 英文
axially symmetric bending
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  • 稱 : 稱動詞（適合; 相當） fit; match; suit
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  1. Abstract : a new type cold frame is intruduced. the deformation of unsymmetry section steel after cooling is mainly eliminated by reversely curring it on line, ensuring the achievement of automation of meticulous repair. at the same time the disposing principle of equilibrium weight on the driving axis of cold frame drived by eccentric wheel was improved. the torsional moment of transmission shaft and power of electric motor are reduced by the method

    文摘:介紹了一種新型冷床，通過在線對非對稱型鋼進行反向彎曲，基本上消除了非對稱型鋼冷卻后的變形，保證了精整工序自動化的實現.同時，提出了偏心輪驅動的冷床驅動軸上平衡重的配置原則.此方法可降低傳動軸上所受的扭矩，減少了電動機的功率
  2. An equal angle section, being a singly - symmetric section, will buckle in a torsional - flexural pattern about any axis except for flexural buckling about the unsymmetric axis

    等邊角鋼截面為單軸對稱截面，除繞非對稱軸失穩為彎曲失穩外，繞其他任意軸均為彎扭失穩。
  3. As regards to the spheric thin shell structure under external hydro static pressure, basing on flat - plate theory and by using basic von karman equations for large deflection, the equilibrium problem of axisymmetric bending of the spheric shell under uniform external pressure is simplified to an equilibrium problem of bending of elastic basic flat - plate and further converted into an equilibrium problem of beam on elastic fundation taking into consideration of the deformation characteristics

    對球形薄殼結構隨靜水外壓的情況，應用平板理論中的vonkarman大撓度基本方程，將球形薄殼在均勻外壓下的軸對稱彎曲平衡問題簡化為彈性基礎平板的彎曲平衡問題，進而再根據變形特點將其轉化為彈性基礎梁的復雜彎曲平衡問題。
  4. Analysis of flexural vibration on circular ring of axis symmetry

    一類軸對稱圓環的彎曲振動分析
  5. According to the elastic bucking theory this paper reviews and compares the calculations that such member bend around the reat axis and the hollow axis as well as bend with torsion around the hollow axis. here this paper presents a formula of calculating b used in with the h - shaped anglicizing element. meanwhile, this paper deduces out a formula of calculating b. by, which the member could be controlled to only buckle around the real axis

    本文根據彈性屈曲理論對雙肢格構式單軸對稱綴板柱繞實軸、虛軸以及彎扭屈曲進行了計算分析和比較，提出了繞虛軸側向屈曲的換算長細比_ （ oy ） = （ y ~ 2 + l ~ 2 ） ~ （ 1 / 2 ）中的值用h計算單元指出的計算公式，同時推導出了單軸對稱綴板柱只出現繞實軸彎曲屈曲的最小肢間間距b 。
  6. Axisymmetrical bending of tapered circular plates by differential quadrature method

    法分析變厚度圓形板的軸對稱彎曲
  7. The theoretical formula for structural computation of buried stiffened - pipes is derived based on the axisymmetric bending theory of cylinders and thereby a program of structural stress computation and design optimization of buried pipes are developed

    摘要作者根據圓柱殼的軸對稱彎曲理論，推導出地下加勁埋管結構計算的理論公式，並據此編制出地下埋管結構應力計算和設計優化程序。
  8. Focuses are then put on the flexural torsional buckling analysis of mono - symmetry i - section arches. closed form solutions are obtained for arches subjected to uniformly distributed radial load and to equal and opposite end moments. effects of different laying positions and of asymmetry of cross - section on buckling loads are included

    在這個基礎上，對單軸對稱工字形截面拱在均勻受壓和均勻彎曲條件下的屈曲問題進行研究，給出臨界荷載的理論解答；分析了工字形截面不同放置形式和截面不對稱性對拱臨界荷載的影響，並與已有的理論進行比較。
  9. The analytic solution for the bending of the inner edge clampped circular plate subjected to an axisymetric moment

    內孔固支圓板在軸對稱線布力矩作用下彎曲變形的解析解
分享友人
分享到 Line

分享到臉書