軸承殼體 的英文怎麼說
中文拼音 [zhóuchéngkétǐ]
軸承殼體
英文
bearing shell- 軸 : 軸Ⅰ名詞1. (圓柱形的零件) axle; shaft 2. (對稱部分的直線) axis 3. (圓柱形的纏繞器物) roller; spool Ⅱ量詞(用於纏在軸上的線以及裝裱帶軸子的字畫)
- 承 : Ⅰ動詞1 (托著; 接著) bear; hold; carry 2 (承擔) undertake; contract (to do a job) 3 (客套話...
- 體 : 體構詞成分。
- 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
-
Xm ) trundle needle, trundleing the post thrust bearing trundles the needle through the roll part of the body, cylinder roller and thrust maintain shelf and the thrust bed down the livestock to make up, trundleing needle and the cylinder roller is subjected to the shelf maintaining that the thrust maintains and guides. moreover thrust bed down the livestock against the difference, shaft, the pedestal encircles and employs in company, fix module shaft shoulder end face and the shell opening back plane dimensional tolerance, geometry accuracy, rigidity, axial is moved up and down, coarse degree ought to accord with the internation , national standard stipulation demand
滾針,滾柱推力軸承由滾動體滾針,圓柱滾子及推力保持架和推力墊圈組成,滾針和圓柱滾子受到推力保持的保持架引導,並與不同的推力墊圈,軸,座圈一起使用,安裝組件的軸肩端面和外殼孔底面的尺寸公差,幾何精度,剛性,軸向跳動,粗糙度應符合國際,國家標準規定的要求。Now developing successfully “ gearbox synthetic inspection instrumentation ” can measure simultaneously the first and second bearing bore diameter and verticality parameters of gearbox case. information acquisition and data processing is controlled by computer. the instrumentation improves the inspection efficiency and meets the demand of mass - produced
本課題研製的變速箱殼體綜合檢測儀可實現在線檢測變速箱殼體一軸軸承孔直徑、二軸軸承孔直徑、一軸端面垂直度、二軸端面垂直度等幾何參數。Sun hydraulik gmbh offers offers to screw - in valves, globe valves and valve housing
提供軸承箱、軸承體、閥體、閥箱、閥套、閥門外殼及其它產品。Hydraulic fluid power - cylinder ; piston seal housings incorporating bearing rings ; dimensions and tolerances
液壓流體動力.裝有軸承環的活塞密封殼體.尺寸和允公With the different loading ratio of parallel to axis and normal to axis direction, damage defects will occur bulking problem. by varying the degree of material anisotropy relative to the loading axis such as poisson ' s ratio and shear modulus, crack growth bulking strain value parallel to or normal to the loading axis is different. the parameters controlling the growth or arrest of the delamination damage are identified as the geometry and the depth of defects and radius of cylindrical etc. at last, it was investigated that the delamination damage is often induced by the tip of matrix damage under higher stress
研究結果表明:殼體筒段受軸向拉伸和內壓載荷作用時,軸向和環向載荷的比率不同,母層和子層可能發生拉伸屈曲,也可能發生收縮屈曲,或者同時發生拉伸和壓縮屈曲;母層與子層各向異性存在差異,即泊松比與剪切模量不匹配時,將使子層板的邊界上承受壓縮和剪切作用,當分層達到臨界狀態則發生屈曲,當母層與子層的各向異性差異越大,則發生分層屈曲的可能性越大;分層損傷的屈曲應變值與子層自身的彈性模量、分層子層的形狀、厚度以及圓柱半徑等因素有關。Hydraulic fluid power, cylinders - housing dimensions for rectangular - section - cut bearing rings for pistons and rods iso 10766 : 1996
液壓流體動力液壓缸.活塞和連桿的矩形截面軸承環的殼Rolling bearings. accessories. plummer block housings in two pieces
滾動軸承.附件.兩件組合的止推軸承殼體Rolling bearings - bearings with speherical outside surface and extended inner ring width - specification for dimensions of cast and pressed housings
滾動軸承.第3部分:外球面加寬內圈軸承.第3部分:澆鑄和壓制軸承殼體尺寸規范Rolling bearings - cast and pressed housings for insert bearings
滾動軸承.帶箱體軸承用鑄造壓制外殼體分享友人