軸承間隙 的英文怎麼說

中文拼音 [zhóuchéngjiānxì]
軸承間隙 英文
bearing clearance
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 隙 : 名詞1 （縫隙; 裂縫） crack; chink; crevice 2 （空閑） gap; interval 3 （漏洞; 機會） loophole; op...
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  • 間隙 : （空隙） interval; gap; freedom; space; [機械工程] clearance; separation; stricture; clear; inter...
  1. Many international experts have done research in amb - ab, but the air bearing occupying a long axis space. the rotor ' s dynamics performance is depressed. a new type amb - ab was brought forward in this paper, the film air bearing was integration in amb

    本文研究了一種新型的磁氣混合軸承結構，其特點是將箔片氣體軸承集成在磁軸承的氣隙裏面，不佔據軸向空間，因此與國外的研究有本質的區別。
  2. Measure the clearance of bearing by pressing lead wires

    用壓鉛法測量軸承間隙。
  3. Countershaft assembly uses tapered bearings to reduce end play and extend gear life

    7中間軸組合使用錐形滾柱軸承以減少軸向間隙並延長齒輪使用壽命。
  4. We illustrate the wavelet package analysis that can obtain the time - frequency distribution figure of noise signal, which can be used to define gray - image. through image - average, we can get the standard time - frequency distribution images of different main bearing gap. based on that, a main bearing wear fault diagnosis model using image matching is set up

    然後對圖像進行平均，得到主軸承在不同間隙狀態下的「標準」時頻分布圖，建立了柴油機主軸承間隙圖像匹配的故障診斷模型，匹配時所用的參數為兩幅圖像之間的歐氏距離。
  5. When the fit between bearing and housing is clearance fit, the bearing ' s outer ring has anti - rotation ball ( pin )

    當軸承與軸承座為間隙配合時，軸承外圈帶止動球（銷） 。
  6. Based on the tribological principle and the theory of contact mechanics, it is feasible to adopt curvature - changing structure in the rock - bit journal bearing system. the structure and coupling relationship of curvature - changing journal bearing under the condition without friction have been analyzed and three kinds of sub - form structure configurations, namely, the pseudo - curvature - changing structure, the conformable curvature - changing structure, and the clearance curvature - changing structure, been differentiated according to the contacting features. the shape optimization and pre - running - in regulations of the contact surface of curvature - changing journal bearing under friction condition have been established. the results of rock bit journal bearing test indicate that the tribological behavior of the bearing can be effectively improved by curvature change based on both designing and pre - running - in

    基於摩擦學原理和接觸力學理論，提出了可在牙輪鉆頭滑動軸承中採用變曲率結構.在不考慮摩擦的情況下，就結構設計和配合關系等問題進行了分析討論，劃分了準變曲率、吻合變曲率以及間隙變曲率等3種結構形式；針對考慮摩擦時的變曲率結構，提出了接觸形狀優化和預磨合的實施方案.鉆頭軸承試驗結果表明，無論是預設計變曲率還是預磨合變曲率，都能改善軸承摩擦副的摩擦學特性，因而值得進一步研究和推廣
  7. These rubber mills are distinguished from our other polymer mills by a more heavy duty build up of the rolls, bearings and nip - gap adjustment as well as a significantly larger drives where the rolls are directly coupled to heavy - duty helical bevel gears

    橡膠兩輥開煉機由我們其他的聚合物兩輥開煉設備發展而來，但是具有更堅固的結構設計，包括輥筒、軸承、間隙調整等部分。
  8. Abstract : guiding accuracy of casting mould depends on structure and oscillation parameters, such as elastic deformation of guiding leaf - springs, play of bearings between linkages, stroke and frequency of mould oscillation, etc. in this paper, these factors are studied by means of kinetic and dynamic analysis of oscillating mechanism

    文摘:通過對連鑄機結晶器振動機構的運動學和動力學分析，研究了導向板彈簧的彈性變形、連桿軸承間隙等結構參數及振幅、振動頻率等運動參數對結晶器仿弧誤差的影響。
  9. There is one oil groove in the bronze bushing, where lubricant can flow into the axis from the oil hole on the cap of housings

    軸瓦內表面的不承擔載荷部分開有油槽，潤滑油通過進油孔和郵溝流進間隙。
  10. Measuring clearance between propeller shaft & bearing

    螺旋槳軸與軸承間隙測量。
  11. Lubricating spindles with narrow bearing clearance in machine tools

    亦可用作潤滑機械工具中，狹窄間隙軸承的軸心。
  12. Ball bearings, conrad type, for electrical machines ; tolerances and radial clearance

    電氣機械用的連桿式球軸承.公差和徑向間隙
  13. To ensure the charging pump working reliably, the following measures should be adopted : ( 1 ) adopting modified circular casing to reduce the radial force of the impeller and decrease the seal clearance ; ( 2 ) using radical ribs on impeller and helical sealing on shaft to realize minor pressure differential ; ( 3 ) using back pressure stuffing box to ensure sealing under small packing force ; ( 4 ) adopting self - lubricant flexible graphite stuffing for absorption of solids entering in the graphite in case of leaking

    為確保灌注泵可靠工作，提出改進措施： （ 1 ）採用改型環形泵體降低葉輪的徑向力，減小軸封間隙，抑制泄漏； （ 2 ）採用背葉片降低葉片根部壓頭，獲得微壓，使軸封兩端承受較小壓差； （ 3 ）採用螺旋密封降低軸封兩端壓差，在保持微壓的同時避免出現負壓，密封效果更好； （ 4 ）採用反壓式填料密封結構，在很小的壓緊力下，即可保證密封； （ 5 ）採用具有潤滑功效的柔性石墨填料，即使發生軸封泄漏，進入石墨內部的固相顆粒也將隨著石墨的消耗而被鉆井液吸收。
  14. Measuring installation clearance of rudder bearing

    舵軸承安裝間隙測量。
  15. Plain bearings - quality assurance of thin - walled half bearings - selective assembly of bearings to achieve a narrow clearance range iso 13778 : 1999

    滑動軸承.薄壁軸瓦的質量保證.選配法獲得小間隙
  16. 399 how many radial ( axial ) clearnance are there in this bush ( journal bearing, thrust bearing )

    這個軸套（軸頸軸承、止推軸承）的徑向（軸向）間隙是多少？
  17. This machine is controlled by the industry control computer, which can measure the clearance along the driving taper gear axes and select the suitable sleeves so that the clearance can be eliminated and the set tightening of the bearing can be achieved

    選墊機採用工業控制機控制、自動化檢測驅動橋主錐齒輪軸軸向間隙，並優化選擇合適的墊片，通過墊片來消除軸向間隙並調整軸承達到設定的預緊力矩。
  18. Sliding frictions and bearing clearances inevitably leading to the gear vibration of a gearing

    滑動摩擦及軸承間隙必導致齒輪機構的齒輪振動
  19. The threshold speed and the typical characteristics of the oil whip of the system are simulated under the nonlinear model of oil film force, and the state of motion and type of the bifurcation are analyzed by floquet multiplicators which is computed by the shooting method. secondly, the the nonlinear dynamical model of the low - pressure rotor - bearing system by column bearing with reduced dimensions is presented. the numerical results show the rule of the amplitude with the eccentricity of rotor, the length - to - diameter ratio, oil viscosity and the clearance - to - radius ratio of the bearing under the definite speed

    其次，對降維后的低壓轉子?軸承系統的非線性動力學方程，計算了圓柱瓦軸承支撐的轉子系統的振動穩定性在固定轉速下隨偏心距、軸承長徑比、潤滑油動力粘度和軸承間隙比的變化規律，並分析了轉子前軸承軸頸的失穩轉速與轉子偏心距、軸承長徑比、潤滑油動力粘度和軸承間隙比之間的關系，同時利用floquet理論分析其運動狀態和分岔類型。
  20. Taking the hydrostatic equilibrium of axial force of pump dm360 as the example, this paper elaborates design calculation and dynamic - static characteristic analysis of hydrostatic bearing with twisting plate throttle, derives design parameters and formulas of bearing structure, discusses effects of various main factors ( oil viscosity, compressibility, distortion coefficient of twisting plate, pressure of oil source, and bearing clearance ) on dynamic characteristic, and obtains some conclusions about the application of hydrostatic bearing in engineering practice

    本文以dm360型泵軸向力的液體靜壓支承平衡為例，對扭板節流靜壓支承的設計計算和動靜態特性分析進行了較為詳盡的闡述，推導出支承結構的設計參數和公式，討論了各種主要因素（油液的粘度、油液的可壓縮性、扭板變形系數、供油壓力、支承間隙）對支承動態特性的影響，給出了一些結論。
分享友人
分享到 Line

分享到臉書