軸狀頸 的英文怎麼說
中文拼音 [zhóuzhuàngjǐng]
軸狀頸
英文
shaft neck-
Methods ： fifty paired embalmed cadaveric humeri ( twenty - five pairs : fourteen from male donors and eleven from female donors ) were scanned in medial - lateral ( ml ) and anterior - posterior ( ap ) position according to the humeral retroversion by ct. images of the humeri in the transverse planes at the lowest border of neck ( lbn ), 20mm and 40mm distal of lbn ( lbn - 20 、 lbn - 40 ), isthmus, head - neck anterior - posterior ( hn - ap ) were obtained. sixty - one extracortical and intracortical parameters were measured exactly by image analytic computer software that included offset, head position, head - shaft angle, head to tuberosity height ( ht ), head thickness, curvature radius, articular surface arc ( sa ), neck diameter, isthmus position, proximal and distal border of isthmus, maximum coronal and sagittal diameter of medullary canal and thickness of cortical bone in four planes, including lbn, lbn - 20, lbn - 40 and isthmus
方法： 50根成對防腐肱骨（男14對，女11對）按肱骨頭扭轉角置於冠狀位和矢狀位，行肱骨全長，頭頸矢狀面，解剖頸下緣及其下20mm 、 40mm ，髓腔狹窄部四平面ct掃描，由ct軟體測量冠、矢狀位髓腔內外參數共61項，包括頭心?干軸距，頭位置，頭干角，頭?結節高度差，頭厚度，頭半徑，關節面張角，解剖頸直徑，髓腔狹窄部位置，解剖頸下緣及其下20mm 、 40mm和狹窄部四個平面髓腔的最大冠、矢狀徑，皮質骨厚度等。The effect of the crank shaft neck profiles on the service characteristics of bearings
曲軸軸頸輪廓形狀對軸承使用性能的影響Axial syndrom and stability after open - door laminoplasty of cervical spine
單開門頸椎管擴大椎板成形術后軸性癥狀與頸椎穩定性的相關觀察The threshold speed and the typical characteristics of the oil whip of the system are simulated under the nonlinear model of oil film force, and the state of motion and type of the bifurcation are analyzed by floquet multiplicators which is computed by the shooting method. secondly, the the nonlinear dynamical model of the low - pressure rotor - bearing system by column bearing with reduced dimensions is presented. the numerical results show the rule of the amplitude with the eccentricity of rotor, the length - to - diameter ratio, oil viscosity and the clearance - to - radius ratio of the bearing under the definite speed
其次，對降維后的低壓轉子?軸承系統的非線性動力學方程，計算了圓柱瓦軸承支撐的轉子系統的振動穩定性在固定轉速下隨偏心距、軸承長徑比、潤滑油動力粘度和軸承間隙比的變化規律，並分析了轉子前軸承軸頸的失穩轉速與轉子偏心距、軸承長徑比、潤滑油動力粘度和軸承間隙比之間的關系，同時利用floquet理論分析其運動狀態和分岔類型。When the dimension of the pump is not particular, you can make a model by reverse engineering. iii ) there is a small flat metal piece on the outside of the torque converter ' s shell, called tab. system can get the axial rigid displacement of the equipment by measuring this tab ' s axial movement
通過本課題研究得到以下結論：一、液力變矩器在加速狀態產生彈性變形引起頸端和柄端的軸向位移和在加壓狀態時產生的彈性變形引起柄端的軸向位移均朝向發動機一側；而在加壓狀態時產生的彈性變形引起頸端的軸向位移方向相反。分享友人