軸距系數 的英文怎麼說

中文拼音 [zhóujùxìshǔ]
軸距系數 英文
coefficient of wheel spacing
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 距 : Ⅰ名詞1 （距離） distance 2 （雄雞、雉等的腿的後面突出像腳趾的部分） spur （of a cock etc ）Ⅱ動詞...
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 軸距 : [設計] wheel base; distance between shafts; spread of axles
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. Then an thorough computer modeling using finite element program with material, geometry and state triple - nonlinear taken into account is carried out on a series of influencing factors, such as comparison with npn - beam splice connection, comparison of varies designed theories, and the varying of fraction coefficient, diameter, grade, pretension and arrangement of bolts, thickness of web and flanges of beam and column, splicing location, axial loading on column, etc. lots of useful conclusions are drawn form computer modelling. finally, design and construction suggestions are given out. this study fills the black in the field of steel beam - to - column connection with cantilever beam high - strength bolted - splicing at both home and abroad

    然後，本文在考慮材料、幾何和狀態三重非線性的基礎上，對該連接形式進行了全面的計算機模擬，主要考慮了帶懸臂梁段全螺栓拼接的樑柱連接節點與無拼接的樑柱連接及翼緣對接焊接腹板拼接的連接節點的對比，各種設計方法之間的對比，以及翼緣拼接和腹板拼接的螺栓間距、直徑和數量，拼接點與梁端之間的距離，梁和柱的翼緣、腹板厚度，柱的軸力，接觸面的摩擦系數，翼緣和腹板拼接板的厚度等因素的影響。
  2. The resonance conditions of the train - bridge system are affected by the span, total length, lateral and vertical stiffness of the bridge, the compositions of the train, and the axle arrangements and natural frequencies of the vehicles

    車橋系統的共振條件與橋梁跨度、長度及豎向和橫向剛度，列車編組、車輛軸距參數及車輛的自振頻率等因素有關。
  3. Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error

    對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。
  4. For the bundle with small number of fibers, the discrete common model is proposed by building a 60 coordinate system ; for the bundle with large number of fibers, the integral common model is proposed by introducing a parameter called distribution density of the distance between fiber axes ; furthermore, the model of combined fiber bundle sensors is introduced

    對于小數目光纖組成的光纖束，通過建立60角坐標系來分析不同排列形式的光纖束，建立了離散式通用模型；對于大數目光纖組成的光纖束，通過引入軸間距分佈密度參量，建立了積分式通用模型；進而給出了組合式光纖束傳感器的模型。
  5. Basing the analysis on the experimental data, the author provides the load - bearing capacity formula of the concrete short column confined by overlapping hoops under uniaxial compression and the relationship between characteristic value of hoop and spacing of hoop, which is of great practical value

    摘要通過實驗數據的分析，提出了軸心受壓復合方箍短柱正截面承載力的計算公式並給出了配箍特徵值與箍筋間距的關系，具有一定的實用價值。
  6. Finally, by using algebraic approach of the two - system screws, we determine both the ranges of the twist pitches and the spatial distributions of all the twist axes

    最後用螺旋二系的代數法分析了它們的運動螺旋節距的取值范圍和螺旋軸線在空間的分佈。
  7. Contrast with the results, the dissertation concludes that the axial loads of column have no essential variation, the variations of moments and shear forces of column are small under horizontal loads in contrast with the structure system in elastic ground, the moments and shear forces variation of column cannot be neglected, and the structure system with different foundation have the close degree variation

    通過對比分析，本文認為水平力作用下交錯桁架體系柱的軸力基本不變，彎距及剪力響應數值變化不大。豎直荷載作用下，與彈性地基計算結果比較，彎矩及剪力均存在不可忽略的變化，且不同形式基礎其影響的程度基本相近。
  8. The distrbution function of intersections is proposed for the case that a long needle is thrown randomly in a double grid system ( equally unit - spaced )

    摘要考慮在間距為1的區域足夠大的方格子系統中投入長度為（ 0 ， + ）的針時，針與方格子的橫軸和縱軸的交點總數的分佈問題。
  9. 1. firstly, the mathematical model of fiber pair with the factors of reflector shape and inclination is established. then, the numerical simulation is fulfilled, along with a series of rules of the influence on intensity modulation property caused by multimode fiber parameters, the factors of reflector shape and inclination

    然後，採用數值模擬的方法系統地研究了多模光纖參數（包括光纖對軸間距、光纖芯徑和光纖數值孔徑） 、反射面傾斜因子以及形狀因子對rim - fos強度調制特性的影響規律。
  10. The physics engine manages a considerable amount of data, such as tyre temperature, chassis torque, weight distribution, suspension geometry, wheelbase, track, braking system characteristics and so on, in order to generate a precision never before experienced in a simulator

    物理引擎管理著相當數量的數據，如輪胎溫度，底盤扭矩，重量分佈，懸浮幾何，軸距，田徑，剎車系統的特點等對，為了產生一個精確以前從未經歷過在一個模擬器。
  11. The main achievements were summarized in detail as follows : ( 1 ) the cfdst tubular beams, columns and beam - columns with chs outer steel tubes were tested systematically. the main experimental parameters were tube diameter - to - thickness ratio, hollow section ratio, eccentricity and slenderness ratio. ( 2 ) load - deformation relationship curves of cfdst subjected to compression and bending were analyzed by finite element method and fiber element method

    本文具體進行了以下幾個方面的工作: （ 1 ）分別以徑厚比、空心率、長細比、偏心距等為主要變化參數，較系統地進行了軸壓、純彎和壓彎構件在單調加載下的試驗研究。
  12. The pad - lock ? washer system has been improved by incorporating the convex pivot adjustment into the backing plate ; thus allowing for the reduction in the number of washers needed to achieve all spacing requirements

    墊板鎖墊圈?系統已得到改善，納入凸樞軸調整到底板;從而使人數減少后的墊圈，以實現所有間距要求。
  13. Axisymmetric numerical model for original casing - eroded wells is established through hydraulic fracturing numerical simulation, and it can help to determine the relationship between distance limit from casing erosion point to fractured zone and fracturing pressure, so as to refrain from casing erosion recurrence in original easing eroded wells

    摘要為解決套損井修復后水力壓裂施工時重新出現套損，以及確定套損點到壓裂層的距離界限，通過對水力壓裂過程的數值模擬，建立了套損修復井的軸對稱計算模型，得出了套損點到壓裂層的距離界限與施工壓力的關系。
  14. The system can measure the static parameters of vehicles, such as static weight, velocity and axle space, provided that the velocity is restrained

    該稱重系統在公路車輛限速行駛狀態下，能測出行駛車輛的靜態質量、行駛速度以及軸距等車輛靜態參數。
  15. The expansion of the reaction products of detonating cylindrical charges is presented and analyzed with regard to the radial and axial mean velocities and the real expansion velocities as a function of time and distance

    對圓筒型裝藥發生爆轟后的反應物的傳播過程進行了研究，分析了軸向平均速度、徑向平均速度和實際傳播速度與時間和距離的函數關系
分享友人
分享到 Line

分享到臉書