載荷強度 的英文怎麼說

中文拼音 [zǎihéqiángdù]
載荷強度 英文
density of load
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 荷 : 荷名詞（蓮） lotus
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 載荷 : load; loading載荷變化 load fluctuation; variation in load; 載荷裝置 load device
  1. In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test

    然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。
  2. With carbureted high - strength good - quality alloy, the series has the feature of high - efficiency and long life - span, high permissible axial and radial loads, low noise, high reliability and compact structure and so on configuration modality

    採用高強度優質合金鋼滲碳游淬火，具有高效率高壽命輪及高許用軸向，徑向載荷，運行噪音低，可靠性高，結構緊湊等優點。
  3. By analyzed interactions of combined limit pipe load components, simplified check formula for pipe load strength are put forward and the calculation method of relevant allowable pipe load values based on shell finite element analysis is presented as well

    通過對組合極限接管載荷分量相互關系的分析，提出了接管載荷強度驗算簡化公式和以殼結構有限元應力分析為基礎的許用接管載荷計算方法。
  4. Road wheel in this paper is created according to gb / t 3487 - 1996 and application of load is simulated the actual situation. msc. patran finished is used to build model of road wheel, divide finite element graticule, apply boundary load, and define material properties, which are submitted to msc. nastran to analyze strength

    本文所使用的車輪是按照輪輞的國家標準而構建的，而載荷的加入是模擬實際情況而添加的，在此基礎上，運用msc . patran ，完成車輪幾何建模，有限元網格劃分，邊界載荷的加入，材料特性的定義，再提交到msc . nastran中進行強度分析。
  5. Road wheel in this paper is created according to gb / t 3487 - 1996 and application of load is simulated the actual situation. ansys finished is used to build model of road wheel, divide finite element graticule, apply boundary load, and define material properties, which are submitted to ansys to analyze strength

    在車輪的構建上，本文採用了三維繪圖軟體ug ，在ug中首先完成車輪幾何建模，然後導入到ansys裏面進行修改並進行有限元網格的劃分，邊界載荷的加入，材料特性的定義，對車輪進行強度分析。
  6. Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )

    本研究以武裝直升飛機防護裝甲材料為研究對象，採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料，結合其力學性能、掃描電鏡和界面微區能譜分析結果，分析了sic _ p al復合材料的真空燒結過程中的界面現象，以及材料增強和斷裂機理，並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態（應變率為3 . 3 10 ~ （ - 3 ） s ~ （ - 1 ） 5 . 2 10 ~ 3s ~ （ - 1 ） ）的壓縮破壞響應進行了研究，分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下，材料的變形和微觀損傷機理，以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。
  7. In the chapter 3, algor feas ( also called super sap ), a commercial fem software is introduced ; several. problems in building the finite element model of a auto frame is researched ; taking advantages of fem and mathematic programming, a strength analysis method of the frame of a series multi - spindle hydropneumatic suspension automobile is proposed ; taking the structure and load characteristic of a missile ' s frame into account, the static, eigenvalue and response analysis have been made by using super sap91

    第三章簡要介紹了大型有限元軟體sap91 ；對車架有限元建模及分析中的若干問題進行了討論；利用有限元法和數學規劃法相結合，提出了一種串聯多軸油氣彈簧懸架車輛車架強度分析的方法；針對某導彈發射車車架的結構和載荷特點，利用sap91軟體對其進行靜力分析、特徵值分析和動力響應分析。
  8. The regularities of pile - top reaction distribution, the carrying load ratio between pile and raft, the settlement and the imparity settlement of foundation in the frame - tube structure and the single wall are influenced by some factors such as the stiffness of the superstructure, the intensity of the soil under the piles, the length and radius of the piles, the distance between the piles, the thickness and the suspended width of the raft

    對豎向荷載作用下的空間筒中筒結構、樁筏基礎和地基進行了三維有限元分析。研究整體結構和單片墻結構在上部結構剛度、樁端土強度、樁長、樁徑、樁距、筏板厚度、筏板外挑寬度等影響因素變化時的樁頂反力分佈規律、樁筏荷載分擔比、樁基沉降和差異沉降規律。
  9. Finally, based on the types of all load, using matlab, the reliability programs are compiled to calculate the reliability index under different design and different load combination. the results can be used to evaluate the relatively safety, and direct the leak hunting

    最後，基於所得出的各種荷載的分佈狀況，利用matlab環境編制可靠度計算程序，利用該程序計算在不同設計情況下、不同荷載組合情況下的管壁強度可靠度指標。
  10. A three layered magneto - electro - elastic half - space subjected to vertical mechanical loads, charge or magnetomotive force is analyzed as the numerical example, and the calculative results of two different stacking sequences are compared

    以在垂直機械載荷或電載荷或磁感應強度作用下三層半無限壓電壓磁彈性體為算例，並比較了兩種不同材料疊放順序的計算結果。
  11. High - strength structural bolting for preloading - hrc system - preloaded bolts

    預荷載高強度結構螺栓. hrc系統.預荷載螺栓
  12. By the check - out, inspection and measurement to start construction the industrial art to this test pile with the examination between stake body mass and bearing power, made sure the stroke reasonable operation method drilling under the dissolved cavern geology term ; the pier foundation loading test expressed the lading and rub the lading that resistance drag a glazing for of relation, and to the borehole cast - in - place concrete pile in the karst terrain deliver with break the mechanism, the characteristic of bearing power, proceeding the spot test job of the full of result ; the test data expresses the stake side friction resistance to rises with a bat batch terminal friction resistance very important function, the of tip of pile resistance drag occupies the proportion very few

    通過對本次試樁施工工藝的檢測和樁身質量及承載力的檢驗，確定了沖擊鉆在溶洞地質條件下的合理使用方法；基樁承載實驗表明了荷載與摩擦阻力之間的關系，並對巖溶地區的嵌巖灌注樁的荷載傳遞和破壞機理、承載力特性，進行了富有成果的現場測試工作；試驗數據表明樁側摩阻和支盤端阻起很重要的作用，樁端阻力所佔比例甚少。這與設計樁基時的計算模式相差很大，承載力也較設計增加；使用力學數值分析方法和有限單元法，對鉆孔灌注樁樁端下的巖體強度和結構穩定性方面進行模擬計算和定量研究。
  13. This article gives the subsistent ability and the analysis result of intensity after repair in the open field airplane composite material structure by research the intensity, rigid and repair problem under a axis compress loads on a typical three stiffened composite laminate which has a penetrability crack ( a scatter damage ) by a shrapnel

    本文通過飛機典型復合材料三加筋層壓板結構在被彈片劃開一穿透性切口（離散源損傷）后，在軸向壓縮載荷作用下所產生的強度、剛度以及修理問題展開了技術研究及探討，給出軍機復合材料加筋板在彈擊後生存力以及外場修理后強度恢復分析結果。
  14. It also has important reference value for the similar construction. by the safety and seismic evaluation of this aqueduct bridge, it has shown that ( 1 ) besides the structure of this aqueduct bridge was basically unharmed without some flake of concrete cover and revealing stirrup, its intensity basically reached the need of primary design. ( 2 ) from the side of carrying capacity, rib arch could satisfy the needs under the action of wind and earthquake, but some individual frame crossbeams and most rib arch tie beams could n ' t satisfy the need

    通過對東滑峪渡槽進行安全性能和抗震性能評估后表明： （ 1 ）渡槽除肋拱頂面有保護層剝落、箍筋外露，結構基本完好，其強度基本達到西安理工大學工程碩士專業學位論文原設計的強度要求； （ 2 ）從承載力方面看，在風荷載、地震作用下，肋拱基本滿足要求，個別排架橫梁不滿足要求，肋拱連系梁普遍不滿足要求；計入水平橫槽向地震作用的工況為設計控制工況。
  15. The s - n curve, the mathematical relationship of bend fatigue strength or life to strengthening loads and strengthening cycles, the maximum increments of fatigue strength and life were obtained by experimental digital processing

    通過對試驗數據的處理，得到了兩種結構彎曲疲勞強度的s - n曲線、彎曲疲勞強度和疲勞壽命與強化載荷、強化次數之間的數學關系，以及經過低載強化后彎曲疲勞強度和疲勞壽命提高的最大幅度。
  16. Analyze whether the assembly relation between the parts is rational, whether exists interfere appearance, analyze the loaded intensity of each part

    分析零件之間的裝配關系是否合理，是否存在干涉顯現，分析各個部件的載荷強度。
  17. Bearing capacity and displacement are two main problems in the application of geotechnical engineering. based on a series of pull - out tests using three kinds of paper and a sort of window screening as geogrid, twenty - seven in limit and several in working - stress geogrid - reinforced slope model tests designed through orthogonal principle have been conducted to have obtained the relationship between the bearing capacity and four factors ( i. e. reinforcement, angle of reinforced slope, the designed - length of reinforcement and the distance between layers of reinforcement ). the law of slope lateral ( horizontal ) displacement versus to the height of slope vary with external - load was derived from the model test data, and the main factor affecting the lateral and vertical displacement of geogrid - reinforced slope was obtained through analysis

    承載力（強度）和變形是巖土工程應用領域的兩大主要問題，本文以紙和窗紗布模擬加筋土邊坡的土工格柵，在一系列拉拔試驗的基礎上，以正交設計理論分別安排27個極限應力狀態和若干個工作應力狀態加筋土邊坡模型試驗，並以模型試驗獲得的數據為依據，採用誤差、極差及回歸分析方法，探討了加筋土邊坡承載力與筋類、筋長、層間距、坡角4因素的相關關系，獲得了在外荷載作用下加筋土邊坡的側向位移隨坡高的變化規律（並進行了定性解釋）和坡頂的豎向位移特性，並分析其主要控制因素。
  18. As the basis of reliability or failure probability analysis, load - strength interference analysis can be performed at the levels of component or system, or under the background of order statistics

    摘要作為可靠性或失效概率分析的基礎，載荷強度干涉分析可以在零件的層次上進行，可以在系統的層次上進行，也可以在次序統計量的意義上進行。
  19. Firstly, the displacement, stress, strain fields and the working state of dam body and foundation are evaluated by fem. by overloading the upstream water level and reducing rock strength parameters, the failure process of dam foundation is simulated and the failure mode and paths are determined. the results show that when overload method is used, damaged area develops from up - stream to down stream with failure front stays near the interface between dam body and bedrock

    首先採用非線性有限單元法對壩體及壩基在不同荷載工況下的變位、應力應變狀態展開分析，評價各工況下壩基的運行狀態，而後採用超載法和綜合法對大壩穩定性進行分析，模擬壩基的漸進性破壞過程，追蹤巖體破壞狀態的發展演變過程，從而得到壩基在超載和強度下降過程中的破壞模式和破壞發展路徑。
  20. The analysis of allowable pipe load calculation method and practical example shows that the calculation method suggested is feasible and effective in solving the problems of pipe load strength design

    通過對許用接管載荷計算方法及算例的分析表明，提出的方法是可行的，可有效解決封頭接管載荷強度設計問題。
分享友人
分享到 Line

分享到臉書