載體結合鐵 的英文怎麼說
中文拼音 [zǎitǐjiēgětiě]
載體結合鐵
英文
carrier-bound iron- 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
- 體 : 體構詞成分。
- 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
- 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
- 鐵 : Ⅰ名詞1 （金屬元素） iron （fe） 2 （指刀槍等） arms; weapon 3 （姓氏） a surname Ⅱ形容詞1 （形容...
- 載體 : [化學] carrier; supporter; isotopic carrier
- 結合 : 1 （發生密切聯系; 聯合） combine; unite; integrate; link; binding; coalition; cohesion; connectio...
-
The results show that the composites were more wear resistant than the matrix, contributing to the " volume effect " and " size effect ", the wear resistance increases with the particle content and size. the composite shows better wear resistance than high chromium cast iron material especially in low load and fine abrasive test condition. the results also indicate that the composite strengthened by ageing treatment was more wear resistant than as - cast composite
磨損試驗結果表明，鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料具有比較高的抗磨料磨損能力，而且其耐磨性隨著鑄造碳化鎢顆粒體積分數及尺寸的增大而提高，表現出了強烈的「體積效應」及「尺寸效應」 ，尤其是在低載荷、細磨料磨損條件下，復合材料表現出更好的而寸磨性，即使與高鉻鑄鐵（ cr28 ）相比也有很大程度的提高。4. to get the motor ' s performance by calculation with known formulas, as a result an adjustment for the motor ' s configuration can be practised. when a combined method of altering the length of armature, the number of turns in the winding and the dimension of permanent magnet is used. 5. to get the motor ' s performance when it is driven by the power converter. finally, the calculated data are compared with the experimental measurements, so as to verify the rationality and reliability of the method
Q採用數值分析直軸負載磁場和交軸電樞反應磁場的方法來計算，得到較為準確的結果；根據電機工作特性的計算公式計算電機性能，由計算結果調整電機的結構，而調整工作使用改變電機鐵心長度、繞組匝數和永磁體尺寸相結合的方法，這樣可以得到較為理想的結果；對變頻電源供電時電機的工作特性進行計算，以檢驗其變頻時的性能。Concerning the tests, analyses, design and calculation of performances for light gauge steel framing, this paper focuses on following items : ( 1 ) the calculation of light gauge steel framed compound bearing walls ( lgsfcbw ) in compression and bending. based on north american specification and commentary for the design of cold - formed steel structural members, which was published by the american iron and steel institute, the detailed design requirements of wall stud assemblies are given considering the structural contribution of the attached sheathings and shear diaphragm is discussed briefly. then the calculational theoretic and method for sheathing braced wall stud assemblies complying with national code is brought up in compression and bending
本文圍繞輕鋼龍骨體系結構性能的試驗、分析、設計和計算，主要進行了以下四方面的研究工作： （ 1 ）輕鋼龍骨復合承載墻體的受壓、受彎計算：以美國鋼鐵協會發行的北美冷成型鋼構件設計規范及其規范說明為依據，重點考慮罩面材料對墻龍骨設計的影響，給出了目前對承重墻龍骨設計的具體要求，並對剪力蒙皮進行了簡要討論；然後提出了符合我國規范術語的剪力蒙皮作用的輕鋼龍骨復合承載墻體（即罩面支撐墻龍骨）受壓、受彎的計算理論和方法；最後對提出的計算進行簡化，使之完全與我國規范相符。Polymer networks have been produced in a variety of liquid crystal phases in cells without surface treatment. the liquid crystal / monomer mixtures are prepared using a ferroelectric liquid crystal and a diacrylate monomer. the polymerisation of the monomer is carried out by uv curing the mixture when it was kept in a specific phase which can be obtained by controlling the temperature of the ferroelectric liquid crystal. both the monomer and the polymer network will depress phase transition temperatures. the effects of the polymer network on the packing arrangement of the ferroelectric liquid crystal molecules are examined by means of optical microscopy. the molecular packing arrangement of the ferroelectric liquid crystal in a specific mesogenic phase is frozen on the formation of a polymer network in the ferroelectric liquid crystal in that phase. the existence of the diacrylate based polymer network can improve the electrooptical switching of the ferroelectric liquid crystal
在灌裝于未經表面處理的樣品盒內處于不同狀態的液晶中制備聚合體網路.液晶/單體混合物由鐵電液晶和雙丙烯酸單體製成.單體的聚合通過維持該混合物處在一定的液晶態的條件下經紫外線固化來完成.不同的液晶態可通過控制鐵電液晶的溫度來獲得.雙丙烯酸單體或聚合體網路的存在會導致鐵電液晶載體的相變溫度降低.通過光學顯微鏡可觀察聚合體網路對鐵電液晶分子組合排列的影響.結果發現:在某一液晶態中鐵電液晶分子的組合排列可被在該液晶態中聚合而成的聚合體網路所穩定，雙丙烯酸基聚合體網路的存在可改良鐵電液晶的電光開關特性分享友人