輥距 的英文怎麼說
中文拼音 [gǔnjù]
輥距
英文
roll(er) spacing-
The mill consists mainly of rolls, frame, bearings, roll nip adjusting screws, heating and cooling devixe, emergency stop, lubrication system and such sctions as electrical controls and, etc. the mainelectric motor arives the front and rolls to rotate oppositly through reducer, drving gears and friction gears
本機主要由輥筒機架軸承調距裝置加熱冷卻系統事故停車裝置潤滑系統和電氣控制系統等部分組成。Conveyor belts - determination of minimum transition distance on three idler rolls
輸送帶.三個導輥的最小變換距離的測定Discussions on the distance between holding rollers in long - distance rubberized tape conveyors
長距離膠帶輸送機的托輥間距探討Short - pitch transmission precision roller and bush chains, attachments and associated chain sprockets
短節距精密傳動輥子鏈和套筒鏈附件和輔助鏈輪The effect of carding feed plate and taker - in on card sliver quality
梳棉機給棉板與刺輥隔距對梳棉質量影響Conveyor belts - determination of minimum transition distance on three idler rollers
輸送帶.三個導輥的最小變換距離的測定Conveyor belts. formula for transition distance on three equal length idler rollers. for coal mining
煤礦用帶式輸送機滾筒與相鄰槽形.托輥組之間的距離計算公式Belt drives. v - ribbed belts. determination of measurement of pitch, angle and cord position
皮帶傳動裝置. v形加筋皮帶.輥距角度和繩索位置的測定Too much space between licker in covers and feed plate
刺輥、罩板和送料板間隔距小。Influence of gauge of carding feeding plate and linker - in on carding quality
梳棉機給棉板與刺輥隔距對梳棉質量的影響Wider setting between licker - in and cylinder
刺輥與錫林間的隔距太大。Characteristics of structure : this machine adopts shaft type speed reducer drive which covers less space and can be conveniently repaired. upper supporting roller adopts clamping type fixu which can be conveniently installed. furthermore, it can well regulate deflection of conveying belt ; holdback is set for speed reducer with reliable performance to prevent back - slippign of the glusive belt ; dumper has three types : pneumatically actuated, electric and manual ; course of direction - change roller of the rail has three types : 300, 500 and 800
2結構特點:該機採用軸裝式減速器驅動,佔用空間尺寸小,安裝維修方便上托輥採用夾緊式固定,安裝方便調整輸送帶跑偏能力強,減速器內設逆止器,防止膠帶倒滑的性能可靠卸料器有氣動電動和手動三種驅動型式尾部改向滾筒張緊行程有300 500 800三種,用戶可接輸送距離的1100選取。Abstract : this article is based on the theory of fuzzy optimization design. the running speed and width and initialtensileforce and interval distance of roller are its design variable. the objective function is the minimum power loss of the traction motor. it constructs the fuzzy optimization mathematical model of the two - way running belt conveyer ' s main parameters
文摘:以模糊優化設計理論為基礎,以雙運帶式輸送機輸送帶的運行速度、寬度、初張力及托輥間距為設計變量;以牽引電機運行的最小功率消耗為目標函數,構造出了雙運帶式輸送機主參數的模糊優化數學模型。Based on the application of long belt conveyor, introduced in brief the design essential - layout of the whole machine, requirements of the start - stop control and the caculation of dynamic analysis ; summarized on emphasis collocation and requirements of the main components ( including drive device, turn - over device, tension device, cleaning device, cylinder and supporting roller ) and introduced the start - stop control and measures of deflection - proof
摘要針對國內長距離帶式輸送機的應用情況,概要介紹了長距離帶式輸送機的主要設計環節整機總體布置、起制動控制要求、動態分析計算;重點總結了其主要部件(包括驅動裝置、翻轉裝置、拉緊裝置、清掃裝置、滾筒、托輥)的配置方式和要求;並就其啟制動控制和防偏措施進行了的歸類總結。Concentric roll a perfectly round roll ; a roll having all point on the circumference equidistant from the axis of the roll
中心輥?相當圓的輥子。周圍所有的點和中心軸都等距。Size reduction is attained by shearing stress and pressure, which are generated by high torques at the crushing roll
在由破碎軋輥長距進行緩慢圓周運動時所產生的壓力和切力的The results indicate that the time of press influences sawtooth distortion greatly, but infects sawtooth less. root of the sawtooth made by the method of static simulating rolling have no changes hardly, and from the upper distance the changes became, then on the top the sawtooth curves to the opposite direction
結果表明:壓制時間對齒形的變形影響較大,對齒型的影響很小;模擬軋輥壓制的鋸齒,根部一段幾乎沒有變化,是從一段距離開始變形,然後在頂端向相反的方向彎曲;壓製成型后,鋁板厚度的變化很小。Estimating the distance between rollers of belt conveyor
帶式輸送機托輥間距的確定分享友人