輥軋成形機 的英文怎麼說
中文拼音 [gǔnyàchéngxíngjī]
輥軋成形機
英文
roll former-
Rolling - cutting biscuit shaping machine is new equipment of making soda biscuit, good toughness of thin biscuit and super - thin biscuit. it ' s high production efficiency, low noises, safe operation, convenient, beautiful outer shape. this machine can press and roll rough flour 3 times and equiped with remaining flour recycling machine, also equiped with double - rolling cutting shaped equipement, in the mean time, it can produce two biscuit embryo of differnt shape. 3 times pressing - rolling machine can adjust different thickness and biscuit rough surface. it can roll rough flour and do not stick to rough flour embryo, correctness rate of adopting mould to cut margin of flour embryo reaches 100 percent so that avoid deforming of embryo due to deviation. this machine is one equipment which adopting advanced and won first technical rewarding for its independently control operation, beautiful outer appearance
滾切式餅干成型機是連續製作梳打餅、韌性和薄餅超薄餅的新型設備，具有生產效率高、噪音低，操作安全、方便，外型美觀等優點，本機具有三道軋輥制皮和余料回收機，配備雙滾切成型裝置，同時能生產兩種不同形狀的餅干胚不停機，三道軋輥能同時調節不同厚度和餅皮具有軋輥不粘皮、採用印模切邊一次同步進行準確率100 % ，避免偏差而造成餅胚變形，該機具有獨立控制操作，外形美觀，是目前國內較先進而獲得技術一等獎的設備。Drawing module, which is graphic system of 1c ad, consists of geometric and three - dimensional parameterization model design of work roll, backup roll, mill framework and finishing mill
繪圖模塊由智能cad的圖形處理部分組成，包括工作輥、支撐輥、機架和精軋機的幾何建模和三維參數化設計。The possible factors including the deviation of temperature in length and breadth of rod, the changes of transfiguration resisting force under the changes of temperature, the adjustment of roll gap, the variation of rolling pressure, the changes of roller speed during dynamic adjusting press, the unmatched of seconds - flux under the dimension fluctuation of the coming sample and so on. the whole system was a closed loop which factors in it interacts each other
可能的影響因素有:沿軋件縱橫向溫度變化、由溫度引起的軋件變形抗力變化、軋機輥縫值變化、負載變化、電機調節系統由不穩定向穩定過渡過程中軋輥轉速的變化（如咬鋼過程中的動態速降后的回復階段） 、來料尺寸波動造成秒流量不匹配等，整個模擬系統是各個因素相互影響關聯的一個閉環系統。Safety of machinery - safety requirements for tube forming and rolling mills and their finishing line equipment ; german version en 13675 : 2004
機械安全.管成形輥軋及其精整線設備的安全要求The configuration of conventional backup and work rolls for revamped 1700 tandem cold rolling mill at wisco was proved unreasonable by systematical test as the cause of work roll edges contact during thin strip rolling and unsatisfactory flatness of product
摘要通過現場跟蹤測試和生產實踐發現武鋼1700冷連軋機組「酸軋聯機」改造工程中存在常規凸度輥形配置方案不合理，由此引起了薄規格軋制的工作輥「壓肩」現象和軋制過程欠穩定導致成品板形質量欠佳等問題。And relying on this, our laboratory proposes a new cladding method. by means of large dynamic explicit fem code ansys / ls - dyna, the numerical simulation was carried out in bimetal forming process. during the simulation of the forming process, the large deformation of the strip should be considered, as well as geometrical and material nonlinear, the contact between the roller and the strip, the contact between two metal sheets and the load. as for these problems, we can use node to surface contact and relative parameters, biso model is introduced, the load is applied as array
本文採用ansys / ls - dyna計算程序為分析工具，對鋸齒形雙金屬復合板成型過程進行計算機數值模擬，在對軋制過程模擬時，針對軋件變形的幾何非線性和材料非線性特點、軋輥與軋件間的接觸、軋件間的接觸以及模型的加載等問題，給出了在ansys / ls - dyna中相應的解決方法：應用nodetosurface接觸方式，設定相應參數，選用雙線性等向硬化模型，載荷作為array施加在剛體質心。Model hv - 207a colored steel tile forming machine consists of decoiler and its base, coil sheet building equipment, roll forming system, pressing equipment, post - cutting equipment, hydraulic station, and controlling system. product feature and usage : the colored steel tiles produced by this line look beautiful, elegant and noble. they are widely used as the roof of garden - like factory, hotel, exhibition center, villa, civil construction, etc
經該機輥軋沖模成型的仿古玻璃瓦具有外形美觀古樸典雅造型考究別致品位高貴等特點，可廣泛用於花園式工廠，旅遊風景區，亭臺樓榭，賓館別墅，展覽館，度假村，家庭等建築及室外裝飾。A 2 dimensional varying thickness finite element model of roll system deformation was built to simulate and analyse rolling process, and then a vcr ( varying contact backup roll ) was designed for the rolling conditions of pl - tcm ( pickling line combined with tandem cold rolling mill ) and has been app - lied to 1700 tandem cold rolling mill at wisco after industrial test
採用二維變厚度有限元方法建立輥系彈性變形模擬模型，研製了酸軋聯機條件下的vcr變接觸支承輥，經過工業軋機現場軋制已成功投入1700冷連軋機實際應用。分享友人