輥軋 的英文怎麼說

中文拼音 [gǔnyà]
輥軋 英文
rolling輥軋成形 roll forming; 輥軋梁 rolled girder
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  1. Through examining the roll strength in the leaf blade special - purpose rolling machine, this article has confirmed the feasibility of rolling leaf blade in the new rolling machine

    摘要通過對葉片專用輥軋機軋輥的強度進行校核，驗證了在新型輥軋機上軋制葉片的可行性。
  2. A wise king winnows out the wicked ; he drives the threshing wheel over them

    26智慧的王、簸散惡人、用碌碡輥軋他們。
  3. There are sever kinds of strap mills : horizontal mills - - two roll strap mills and four roll strap mills, and vertical mill with upper drive and bottom drive

    帶鋼軋機有二輥帶鋼軋機和四輥帶鋼軋機，都是水平輥軋機，還有上傳動立輥軋機和下傳動立輥軋機。
  4. The development of heavy plate mill and the common characteristics of the mill revamping were summarized, and the production technologies, such as control links of tmcp, appliction of edger mill and the processing of steckel mill for plate were introduced

    綜述了厚板軋機的發展及其技術改造的特點；介紹了厚板生產tmcp技術的控制環節，立輥軋機的應用以及卷軋中板的生產工藝特點。
  5. Responding to the call of industrial policy adjustment in our country, yaoyu special steel company has started replacing hot - rolling with cold - rolling in the production of electric steel since 2003. it entrusted xinye gaoke group to make design and build the production line of cold - rolled electric steel with annual output of 200 thousand tons. after three years of construction, it has achieved the successful trial production of 20 - roll mill and continuous annealing and coating machine imported from germany

    耀宇特鋼從2003年開始，響應國家產業政策調整的號召，開始電工鋼以冷代熱技改工程，委託新冶高科集團原冶金部鋼研院設計，進行年產20萬噸冷軋電工鋼生產線的建設，經過近三年的建設，目前從德國引進的20輥軋機及連續退火塗層機組均已試產成功，為提高產品的性能和質量，同時提升我國電工用薄鋼板的生產作出了卓越的貢獻。
  6. The rolls pulled up on pour front lawn ; the chauffeur hauled up in front of us

    在傾盆大雨的時候輥軋機在草坪前面停下；司機在我們前面。
  7. A wise king scattereth the wicked, and bringeth the wheel over them

    26智慧的王，簸散惡人，用碌碡輥軋他們。
  8. A wise king winnows the wicked, and drives the threshing wheel over them

    箴20 : 26智慧的王、簸散惡人、用碌碡輥軋他們。
  9. The reason that the internal defects little occur at the center points and fissure takes an annular form during three - roll rolling was expounded based on the state of stress and strain at the center of rolled pieces

    根據軋件內部的應力應變狀態，闡述了三輥軋制軋件中心點缺陷產生可能性較小和斷裂呈環向裂紋的原因。
  10. Automatic rolling control system for four - high mill in citi

    公司軋鋼廠四輥軋機自動軋鋼系統
  11. Works on the bending roll system of four - roll rolling mill, the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys, the maximum deformation of the work roll was calculated, and the curve of the gap adopting the least - squares method was fitted, which set the base of the further calculation of load - gap shape

    摘要以四輥軋機的彎輥系統為研究對象，利用有限元分析軟體ansys研究彎輥力和輥間接觸應力引起工作輥形狀的變化，計算工作輥彎曲的最大變形量，並用最小二乘法對輥縫曲線進行擬合，為進一步計算有載輥縫形狀提供可靠的理論依據。
  12. Improvement of assistance of assel mills

    三輥軋管機輔助設備的改進
  13. Specification for rolled zinc

    輥軋鋅規范
  14. Research of non - uniform wall thickness of heavy - wall tube rolled by three - high tube mill

    三輥軋管機組厚壁管軋制壁厚不均研究
  15. Roll forming machine

    輥軋成形
  16. Specification for drawn or rolled iron - chromium - aluminum alloys for electrical heating elements

    電加熱元件的拉伸或輥軋鐵鉻鋁合金規范
  17. Safety of machinery - safety requirements for tube forming and rolling mills and their finishing line equipment ; german version en 13675 : 2004

    機械安全.管成形輥軋及其精整線設備的安全要求
  18. A wheel diameter is based on 610mm 915mm, suitable for grinding large - scale shaft, for example, automobile axle, rolls and large motor core shaft of steel plant papermaking factory

    砂輪直徑以610 915為主，適用研磨加工大型軸承，例如：汽車車軸鋼廠和造紙廠之輥軋滾輪大馬達芯軸。
  19. On the base of the development of thick film pastes technology, ru - based thick film resistor pastes have been studied due to select conductive phase and inorganic binder. state - of - the - art techniques such as rolling, screen printing and sintering were used for sample preparation. effects of ingredients, printing parameters and sintering parameters, microstructure on the properties of thick film resistor ( trf ) have been analyzed with xrd, sem, dsc and electrical tests

    本文在跟蹤國內外厚膜漿料技術發展的基礎上，以釕酸鉍/銀系厚膜電阻漿料為研究對象，通過選用合適的功能相和無機粘結相成分，以三輥軋制、絲網印刷和高溫燒結等制備工藝為技術特徵，採用xrd 、 sem 、 dsc等分析方法和電性能測試手段，系統的研究了漿料中各相的成分配比、制備工藝參數，以及膜層微觀結構對厚膜電阻性能的影響規律。
  20. Considering different microstructures and properties of metal of hardened layer and the core of back - up roller, the distributions of shear stress below surface and the contact stress between work roller and back - up roller of a four - high - mill were simulated with nonlinear fem

    摘要考慮軋輥表面淬硬層與其心部金屬材料組織性能的差別，採用非線性有限元方法對四輥軋機的工作輥與支撐輥間接觸應力及輥內剪應力分佈進行模擬，並將模擬結果與傳統強度校核方法進行了對比分析，研究了軋輥淬硬層厚度對輥間接觸應力的影響規律。
分享友人
分享到 Line

分享到臉書