輸出控制策略 的英文怎麼說

中文拼音 [shūchūkòngzhìcèlüè]
輸出控制策略 英文
export control policy
  • 輸 : Ⅰ動詞1 （運輸; 運送） transport; convey 2 [書面語] （捐獻） contribute money; donate 3 （失敗） l...
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 策 : Ⅰ名詞1 （通「冊」 古代寫字用的竹片或木片） bamboo or wooden slips used for writing on in ancient ...
  • 略 : Ⅰ名詞1 （簡單扼要的敘述） summary; outline; brief account; résumé: 節略 memorandum; aide mémoire;...
  • 輸出 : 1 （從內部送到外部） export 2 [電學] output; outcome; outlet; out fan; fanout; 輸出變壓器 output ...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  • 策略 : 1 （制定的行動方針和斗爭方式） tactics 2 （講究斗爭藝術） tactful 3 [數學] （對策） policy; strat...
  1. In order to eliminate the influence of the output filter capacitor current on the grid current, a novel control strategy for the grid - connected inverter in grid - tied and off - grid modes is proposed. the control strategy can also realize seamless transfer between grid - tied and off - gird modes. the grid - connected inverter can supply power to the critical load when the grid is off

    本文針對傳統並網控制策略進網電流受輸出濾波電容電流影響的問題，提出了一種新的並網控制策略，該控制策略能基本消除輸出濾波電容對進網電流的影響，實現獨立與並網兩模式之間的無縫切換，對關鍵負載起不間斷供電的作用。
  2. This strategy effectively solves the power distribution between the apu and batteries during the drive of the heb. the power control model and multi - torque switching strategy of the driving motors control the charging - recharging current of the batteries within a wide range, which contribute to the improvement of the efficiency

    該策略很好的解決了車輛行駛時輔助動力系統與蓄電池組之間的功率分配，並且驅動電動機採用功率控制模式以及多級動力輸出切換策略，有效的控制了蓄電池的充放電電流，從而提高了整車效率。
  3. While adopts bang - bang control to realize semi - active control of vehicle suspension system equipped with electrorheologic damper, the coulomb damping force of electrorheologic damper is fixed, as the bang - bang control is two - value control actually. the bang - bang control cannot make full use of performances of the electrorheologic fluids

    由於開關控制是一種二值控制，採用開關控制策略實現對電流變液阻尼器半主動控制懸架系統的控制時，電流變液阻尼器輸出的庫侖阻尼力無法連續變化，不能充分發揮電流變液的特性。
  4. Based on the study of transferring characteristics of the lcc - type resonant voltage, the parameter combinations, which make widths and magnitudes of voltage pulses of resonant network adjustable, arededucedo when the following requirements are met : fn > 3, k > 3 or cp / cs > 8, the above circuit is of natural voltage - stabilized characteristics, thus open - loop control method for bucking voltage is presented and the experimental results verify that the method is feasible.,

    實測整機在額定負載時效率達到88以上。在研究lcc諧振網路電壓傳輸特性的基礎上，推導出滿足可變寬度和幅度的諧振網路輸出電壓脈沖列的參數組合。設計f n 3 、 k 3或c _ p / c _ s 8時，諧振網路具有自然穩壓特性，因此本文提出並實驗驗證了一種整機為降電壓時的開環控制策略。
  5. In this paper, a coordinated recovery strategy for multi - infeed hvdc system is proposed

    提出了一種針對多饋入直流輸電系統的協調恢復控制策略。
  6. Compared with the pid controller in the real - time experiment and off - line simulation, it shows that not only the output of system is small overshoot and rapid respond time when the logical rule controller acts, but also its control strategy is easy to be performed

    與傳統的pid控制器作用相比，離線模擬和在線實驗表明，邏輯規則控制器作用下的系統輸出不僅超調量小，響應時間快，而且控制策略簡單易行。
  7. He finds the pitch range after calculated the three important parameters through the bladed for windows software, then presents an optimized control strategy that regulate the pitch angle in terms of the wind speed. it must control the output power because the variational output power brings the variational loads. he confirms and optimizes the control strategy that the output power is the control target, the output power is divided into three parts

    將功率作為系統控制的目標，將功率分成三段進行控制，在低風速區，載荷是有限的，以功率最大化作為控制目標；在額定風速附近，由於處在升力曲線斜率的變化點，功率變化較大，應盡快調整槳距角進入失速區工作，減少載荷的波動，該額定風速區的上下工作點要通過現場試驗的手段來確定；在額定風速以上，使功率維持在額定輸出，減少功率波動，並通過bladed軟體的模擬計算對控制策略進行了驗證。
  8. The control tactics of space voltage vector are investigated, and the simplified algorithm which judges the sector location of reference vector and calculates switch operation time is put forward. by analyzing the current hysteresis control, the relation between switch frequency, and hysteresis bandwidth and input inductance of pwm rectifier is deduced. by applying instantaneous power theory, the principle of pwm rectifier power control is analyzed, and the direct power control by matlab toolbox through estimating active power and reactive power with virtual flux is realized, and the simulation results prove that it is correct

    對常用空間電壓矢量控制策略進行分析，提出了給定參考矢量所在區間判斷的簡化方法，以及電壓矢量作用時間的求取方法；分析了電流滯環控制策略，推導出開關頻率與滯環帶寬以及整流器輸入電感之間的關系；應用瞬時功率理論分析pwm整流器功率控制原理，通過虛擬磁鏈估計有功功率和無功功率，用matlab實現了直接功率控制，並驗證了該控制方法的正確性。
  9. Due to the complexity of the structure and control of cycloconverter - type three - phase hf link inverter for soft - switching based on phase - shift - controlled full - bridge mode, a simple and optimized vvvf control strategy is proposed. this control strategy includes : produced pwm by space voltage vector ( svm ) and equivalent carrier frequency fe = 1 / te are introduced into the pdm control of the cycloconverter ; softened equivalent pwm wave is generated at the notches of hf voltage pulses ; the harmonious control between regulating pulse width by phase - shifted angle and regulating voltage of equivalent pwm is to minimize the harmonics content of output voltage of the inverter

    西安理工大學博士學位論文針對這種前級移相全橋軟開關周波變流型三相高頻鏈逆變器結構和控制的復雜性，提出了一種實現簡單而整體優化的vvvf控制策略:將空間電壓矢量產生p姍的方法svm和等效載波頻率fe = 1 / te引入到周波變流器的pdm控制;按高頻電壓脈沖前後沿軟化等效p翎波;用移相調節高頻脈沖寬度和等效p姍調壓協調控制逆變器輸出電壓，在滿足輸出電壓條件下使諧波最小。
  10. Furthermore, it is easy to use different control strategy in the digital inverter, so different pwm control can be used, in order to optimize the design of output filter and improve the output performance

    同時，在數字變換器平臺上可以方便地實現各種控制策略，達到進一步優化輸出濾波器參數、提高輸出電能質量、提高變速恆頻電源整體效率等目的。
  11. Using torque vector control method can increase motor ' s output torque, and can upgrade motor ' s dynamic characteristic. finally, the thesis gives and analyses running results of the motor control systems after using different control methods

    步進電機轉矩矢量控制策略能夠提高電機輸出轉矩的穩定性和幅值，也提高了電機的穩態和動態特性。
  12. The goal of this paper is, by serial / parallel combination technique of two - transistos forward converters ( ttfcs ), to keep the merits of the ttfc, and to overcome the shortages of it. the interleaving technique is adopted, while in combining ttfcs. the interleaving technique lowers the net ripple amplitude and raises the effective ripple frequency of the overall converter without increasing switching losses or device stresses

    組合式雙管正激變換器由雙管正激變換器串並聯構成，應用交錯控制策略，在保留雙管正激變換器功率開關管電壓應力低和可靠性高的優點同時，克服了等效占空比小、副邊二極體電壓應力高、輸出電流脈動大等缺點。
  13. Secondly, to achieve the independent regulation of active and reactive power output from the generator side which is designed for the purpose of tracing the maximum wind - energy capturing. the paper has analyzed the mathematic model of the ac excited doubly - fed machine and the stator field orientation control strategy of the motor as vscf wind power generator. thirdly, it has put forward and designed the dual pwm converter with the capacity of energy flowing bidirectional aimed at the demand of rotor energy bidirectional flow. the author constructed reliable and integrated experimental system and did a series of experimental study including no - load, cutting - in network and power generation at, below and above the synchronous speed

    論文首先分析了風機運行特性及其最佳風能利用原理，通過模擬及實驗驗證了採用直流電機的輸出特性模擬風力機的最大輸出功率曲線的可行性，並給出了模擬系統的硬體結構；然後為了實現交流勵磁發電機有功、無功功率獨立調節機理，分析了交流勵磁雙饋發電機的數學模型和在追蹤最大風能捕獲變速恆頻風力發電時必需的定子磁鏈定向矢量控制策略；針對雙饋發電機轉子能量雙向流動的要求，提出並設計了具有能量雙向流動能力的雙pwm交流勵磁用變頻器；最後為實現從理論到實踐的全面研究，研製出了一套小功率完整的雙pwm變頻器交流勵磁的雙饋風力發電機實驗系統，進行了空載、並網、同步速及上、下的發電運行等一系列的運行實驗；所完成的模擬和實驗研究均驗證了理論、模型和控制策略的正確性、可行性。
  14. Based on the investigation with several voltage control methods, such as venturini method, instantaneous double - voltage synthesis method and space vector modulation method ( svm ), three new control strategies are put forward. firstly, a time - varying modulation coefficient svm method is proposed to improve mc ' s anti - disturbance performance under the asymmetry input voltage. secondly, a 5 - state switching strategy is presented for mc controlled by the svm method, which reduces the commutation number and switching losses remarkably

    在分析了venturini控製法、瞬時雙電壓法、空間矢量法等電壓控制方法的基礎上，提出了在非對稱輸入條件下矩陣變換器空間矢量法的時變調制比改進控制策略，提高了變換器的抗干擾性能；對空間矢量法的開關策略進行了研究，提出了新型5狀態開關策略，在保證其他性能不受影響的條件下，減少了變換器的換流次數和開關損耗；提出了一種矩陣變換器單電壓合成的新方法，它不僅使得變換器的控制簡單，計算量減少，而且使得開關損耗達到最少。
  15. The ic modulation circuits and microprocessor are used in the control unit. on the side of input of inverter, the maximum power point tracking of solar module is well realized by using a kind of thought of self - optimizing control ; on the side of output of the inverter, a kind of approximate optimum v / f control strategy is used in order to optimize the match between the output of the inverter and load of motor - pump

    在逆變器輸入側，採用自尋優控制思想實現太陽能電池最大功率點跟蹤（ mppt ） ；在輸出側，採用了v / f近似優化的控制策略，以優化逆變器輸出與機泵負載之間的匹配。
  16. This paper expatiated that the mathematics models of ac motor is higher order, non - linear and closed coupling, multivariable input - output system. and introduces the principle and the algorithm of sine pulse width modulation ( spwm ), opened - loop space voltage pulse width modulation control ( svpwm ) and field oriented control ( foc ). finally, realized the control strategies of variable - frequency speed regulating using assembly and c language

    文中闡述了交流異步電機的數學模型是高階、非線性、強耦合的多變量輸入輸出系統，介紹了交流電機的正弦脈寬調制、開環電壓空間矢量的u / f控制和磁場定向控制的原理及控制演算法，並利用dsp構成控制系統，通過匯編語言和16位定點c語言混合編程的方法實現了上述的變頻調速控制策略。
  17. The dissertation refers to comparatively full literatures in the field of vsc, and the development history and characteristics of vsc are summarized, and the elementary concepts, elementary definitions, elementary properties, elementary principles and design methods are particularly introduced, and the causes of the chattering phenomenon are systematically analysed, and the study status of the chattering phenomenon and the main methods to eliminate the chattering are elaborated. for the deficiencies of traditionary methods, three improved methods are developed, which are improved exponent reaching law solution, variable boundary layer solution and the solution by adding an auxiliary continuous control term. for uncertain linear systems, an adaptive fuzzy integral variable structure control stategy ( afivsc ) is put forward to eliminate the chattering around the sliding plane, which introduces fuzzy logic to soften the non - linear discontinuous sig nal in the control variable and utilizes adaptive theory to adjust output membership function according to how much the uncertainty of the system is

    比較全面地查閱了關于變結構控制理論的文獻，總結了滑模變結構控制的發展歷史和特點，詳細介紹了變結構控制的基本概念、基本定義、基本性質、基本原理以及設計方法；系統分析了變結構控制系統抖振產生的機理，並闡述了國內外目前對抖振問題的研究現狀以及消除抖振的主要方法；針對傳統抑制和消除抖振方法的不足，改進了傳統方法，得到了三種新的消除抖振的方法? ?即改進的指數趨近律法、可變邊界層法和附加連續項法；針對不確定性線性系統，在變結構控制策略中引入模糊邏輯和自適應理論來消除滑動平面上的抖振，提出了一種自適應模糊積分變結構控制方案（ afivsc ） ，利用模糊邏輯來柔化控制量中非線性不連續部分，採用自適應理論，根據系統不確定性大小在線調整模糊輸出量的隸屬函數，另外，鑒于模糊控制本質上是有靜差的，所以本文選擇了帶積分項的切換函數，由於積分項的存在使系統較正為無靜差系統。
  18. The paper analyzes the main reason of causing system oscillation when it is adjusted by original pid control method, and proposes control strategy of combining basic value of rotation rate with adjustment value to control pump rotation speed according to non - linear characteristic of the system and control request

    本文分析了原pid控制方案導致系統劇烈振蕩的主要原因，並且針對系統的非線性特點和系統控制要求，提出了將控制量基值與調節值相結合實現對輸油泵系統控制的控制策略。
  19. The thesis emphasis the way and arithmetic of the key equipment of walking reheating furnace : loader machine, unloader machine, walking system, series transfer roll, control system of burning and tracking of steel billet, . make use of the system, we can carry out the function of transferring measuring and weighting, detecting, loading and unloading tracking the steel billet, we can control process of burning and exchange data each other to track the steel billet and manage the process over all of product line. goals of reheating furnace ' s producing process such as high yield, low consuming and pollution, automatic operating mode are achieved

    本文著重研究了步進式加熱爐關鍵設備如：裝鋼機、出鋼機、步進梁、爐前爐后輥道、燃燒控制、板坯物流跟蹤等控制對象的具體控制軟體流程、速度控制曲線、行程計算等具體控制策略和演算法，完成了攀鋼1450熱軋加熱爐基礎自動化系統（ l1 ）和熱工儀表的一級控制，實現板坯輸送、測量、裝出料、物流跟蹤、加熱爐燃燒控制以及板坯庫的數據信息交換，通過plc和二級計算機系統進行順序、定時、聯鎖與邏輯控制，實現了操作自動化與物料系統的全線跟蹤管理。
  20. In the simulation experiment, the whole system model is founded by the software matlab / simulink. using the stator active power computed from the maximal output power of the wind turbine as the reference value of vector control system, the result of experiment approves that the control strategy is true. not only the frequency of stator current is constant, but the control of stator active and reactive are decoupled, and the output power tracks the maximal power of wind turbine

    在最後的模擬實驗中，本文利用matlab軟體建立了系統各部分的模擬模型，選用與風力機最大輸出功率對應的定子有功功率作為矢量控制的參考值做了模擬實驗，並給出了模擬結果，驗證了定子磁鏈定向矢量控制策略的正確性：既保證了定子輸出頻率的恆定，又達到了有功功率無功功率獨立解耦控制的目的，同時還較好地跟蹤了風力機的最大功率輸出。
分享友人
分享到 Line

分享到臉書