輸出槽 的英文怎麼說

中文拼音 [shūchūcáo]
輸出槽 英文
output magazine
  • 輸 : Ⅰ動詞1 （運輸; 運送） transport; convey 2 [書面語] （捐獻） contribute money; donate 3 （失敗） l...
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 輸出 : 1 （從內部送到外部） export 2 [電學] output; outcome; outlet; out fan; fanout; 輸出變壓器 output ...
  1. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  2. To select a cylindrical plane cathode ; to design proper focus electrodes in order to control the formation of beam in methods of solving equations, electrobath and simulation aided by computer. to correct effects of anode hole and work out curves of designing guns ; to discuss plasma cathode guns at last

    選用圓形平面陰極;設計恰當的聚束極形狀以控制電子束的成形，並使用解析法、電解槽法和數值方法三種方法進行設計;考慮陽孔效應對電子束傳輸的影響，修正陽孔效應，給出電子槍設計曲線;最後討論一下等離子體陰極電子槍。
  3. All photoelectric isolates between each channel, input or output plug and play input output i o card, six card slots users use the interface

    各通道之間輸入或輸出之間全部光電隔離即插即用輸入輸出i o卡， 6個卡槽
  4. Abstract : a new waveguide which can change the wide wall of a rectangular waveguide into a symmetric arc wall is named as a cam - rectangular waveguide. comparing to sectoral waveguide, the new waveguide has the same voltage characteristics and is easier to be produced and fixed. an approximate formula of the dominant mode fields and the normalized conductance of a longitudinal resonant slot cut in the curved wall of a cam - rectangular waveguide are given. a resonant slot linear array in c & x band is designed, in which the slot voltage distribution is equiphase and the input is matched. the input voltage stationary ware ratio and the h - plane pattern of the antenna are measured. the experimental results show the conformance with theoretical results

    文摘:把常用的矩形波導一個寬面改成圓弧形構成的波導稱為圓突-矩形波導.這種波導與扇面波導相比：電性能相當；波導管結構更加簡單，容易加工，便於安裝.文中給出圓突-矩形波導中主模場，圓曲面上縱向槽歸一化諧振電導近似公式.設計了c和x波段波導曲面縱向諧振縫隙線陣，縫隙電壓相位為同相分佈，輸入端匹配.實際測量了天線輸入端電壓駐波比和h面方向圖，理論與實驗相吻合
  5. One forward optical transmitter module takes one slot, inside power double - amplification, low driving level 80dbuv, output optical power 4 20mw

    一個正向光發射模塊佔有一個槽位，內置功率倍增驅動放大。驅動電平低80dbuv ，輸出光功率420mw
  6. However, according to ann ' s theory, making use of visual basic development tool, friendly - interface single output three layers " artificial neural network generator base on improved bp algorithm has been developed by the author, and after constructing the model, the value of d _ ( cmax ), finally the gross bed - load transport rate of non - uniform sediment with a wide distribution in flume experiment of stead sediment transportation have been forecasted

    筆者採用的途徑則是根據人工神經網路理論，利用vb開發出界面友好、基於改進bp演算法的多輸入單輸出三層神經網路生成器軟體，並採用該生成器建模，對平衡輸沙狀態下的水槽輸沙試驗的d _ （ cmax ）和總輸沙率進行預測計算。
  7. The flow - measuring system adopts the khafagi flume as the first sense organ to realize the flow / head signal conversion. the head signal is picked up and converted into voltage signal by the buoy - level mechanism and the magnet - resistant angle measuring sensor

    該流量測量系統採用卡發基水槽作為一次敏感器件實現了流量水位的信號轉換，並通過浮子?杠桿測量機構和磁阻式角度傳感器對水位信號進行拾取並轉化為電壓信號輸出。
  8. One forward optical receiver module takes one slot, after power double - amplification inside, send out 1 way rf signal 104dbuv and 1 way level checking signal, or two - distribution output

    一個正向光接收器模塊佔一個槽位，內置功率倍增放大，輸出1路射頻信號104dbuv和1路電平檢測口，或二分配輸出
  9. Can print chinese s receipt printer. . . - built - in chinese about 13052 words and can contact to rs - 232 interface. . . - have lock function and printing speed about 50mm sec. . .

    熱感應機心，可列印中文之發票機，內建13052個中文字，並可連接電腦之rs - 232串列介面或並列介面，輸出24v ，儲存槽具有加鎖功能，支援繁體中文，列印速度達每秒50厘米
  10. Based on the analysis of the kinetic track of the scallion during planting, basic relationships ' among the characteristic parameters of the transplanter with two flexible metal disks, including the velocity of the transplanter, the rate of transplanting, the spacing between seedlings, the angle of releasing seedlings, the diameter and length of seedlings, have been set up in this paper, and then a mathematic model of optimum design for the transplanter with the final planting angle of seedlings ( y = 90 ) has been formulated and solved with good results. according to the optimum solutions, a new type of transplanter with two flexible metal disks has been developed and the field tests of the transplanter have been conducted

    為了實現大蔥機械化移栽，作者分析了國內各種移栽機的結構特點，確定了以撓性圓盤式栽植器為研究對象，在分析撓性圓盤式栽植器的運動軌跡和特徵參數的基礎上，完整地確立了撓性圓盤式移栽機的基本參數：栽植頻率、栽植株距、機組前進速度、輸送帶上秧槽的間距、撓性圓盤半徑、撓性圓盤的轉速、夾苗株數以及傳動比之間的相互關系，並建立了以蔥苗栽植傾角= 90為目標的優化設計數學模型，提出了撓性圓盤式大蔥移栽機的優化設計方法。
  11. In this paper, we study the most serious damming section of the east - one main canal, which is from the entrance of the hao wan flume ( chainage12 + 123. 6 ) to the exit of shang tian yuan tunnel ( chainage24 + 091. 1 ). the main content is analyzing the flow characteristic of the canal, setting up mathematical model of the discharge condition of the east - one main canal, according to the survey section and actual roughness factors, building, bend and so on, we divided the canal into more than loocaculation segments. each segment is calculated by microsoft excel electrical table through computer as permanent transition flow of non - prismatic channel

    本論文研究的渠段為陸渾灌區東一乾渠壅水最為嚴重的渠段，從郝灣渡槽進口（樁號12 + 123 . 6 ）至上天院隧洞出口（樁號24 + 091 . 1 ） ，其主要內容是，分析渠道水流特徵，建立東一乾渠輸水狀況的數學模型，根據測量斷面及實際糙率、建築物、彎道等因素的不同，將渠道劃分成120多個計算段，每段按非稜柱體恆定漸變流，運用microsoftexcel電子表格進行編程計算。
  12. Influence of dc - rail zero - voltage notch on the output of the inverter is investigated, and an important conclusion is obtained that the direction of output current of the inverter is not effected by the voltage deviation produced by dc - rail zero - voltage notch, on the basis of which, a new simple correction approach is put forward. experiment results show that the proposed correction method is effective

    探索了直流母線零電壓凹槽對逆變器輸出特性的影響，得出了母線零電壓凹槽形成的輸出電壓偏差與逆變器輸出電流方向無關這一重要結論，在此基礎上，提出了一種簡便的校正新方法，通過試驗驗證了該校正方法的有效性。
  13. The hybrid method can simulate accurately both the imaging and polarization - dependent diffraction characteristics of a concave grating. to meet the growing need for flattened passband in a practical wdmsystem, three design methods, namely, the tapered output waveguide structure with air - slots, the three - focal - point method and the analytical method of spatial phase modulation, are introduced to achieve a passband - flattened diffraction grating device

    針對實際光通信應用中對通帶帶寬的需求，本文提出了「結合空氣槽的漸變輸出波導結構方法」 、 「三焦點方法」及「顯式公式空間相位調製法」三種使平面集成型衍射光柵波分復用器件獲得平頂型頻譜響應的優化設計方法。
  14. A linear theory of rbwo with inner - slot coaxial structure is analyzed detailedly, and the equation of dispersive relation is deduced and computered numerically. 4. particle simulation is used in rbwo respective with coaxial and partial structure. in the simulation, the output parameters of rbwo such as phasespace, contour, vector, voltage, current, output power, interaction efficiency and microwave radiation

    4 .對同軸和偏心返波管分別進行了粒子模擬，通過改變電壓、電流、電子注位置、磁場等參數來觀察返波管加了內開槽前後相位空間、等位線、矢量、電壓、電流、輸出功率、工作頻率的變化。
  15. We design inversion control circuit with cmos figure pll cd4046 act as core and microprocessor 80c196kc act as assistant controller. adopting a control method that combine fuzzy controller and pll control, improve induction heating power succeed in startup. adopting electric current voltage pair closed loop feedback design, with trough route capacitance voltage and trough route electric current act as pair closed loop feedback signal, guarantee induction heating power output accuracy

    並對系統主電路的元器件參數進行了詳細的計算；設計了以cmos數字鎖相環cd4046為核心、以80c196kc作為輔助控制器的逆變控制電路；採用了模糊邏輯與鎖相環相結合的控制技術，提高了電源的啟動成功率；採用電流、電壓雙閉環反饋方案，採用槽路電容電壓和槽路電流作為反饋信號，從而保證了電源功率的輸出精度。
  16. Then, a power - combiner has an output power over 1watt and a power - combining efficiency of 83 % at 34. 2 - 35. 5ghz was realized. small - signal gain and saturated output power were measured under both continuous wave and pulse wave

    利用小功率晶元設計8路開槽波導功率合成器，給出了連續波工作狀態與脈沖工作狀態的測試結果，包括通帶內小信號增益及飽和輸出功率。
  17. Drive adapter for coupling blade and slot shaft with squared power take - off nf l 34 - 112

    帶功率輸出偶合刀片和方形帶槽軸用驅動轉接器. nf l 34 - 112
  18. The third, some groping researches are made on broadband coaxial line filter output circuit of klystron. a broadband output circuit - mode four coupling slots double - gap output cavity loaded with coaxial filter, which has a workable relative bandwidth bigger than 14 % and fits in with l - band multi - beam klystron, is designed. meanwhile some analysis of its stability and peak power capacity is made

    第三，對速調管同軸線濾波器寬帶輸出迴路進行研究和探索，設計出了一個適合用於l波段多注速調管、相對帶寬超過14的四耦合槽模強耦合雙間隙腔加載同軸線濾波器輸出迴路，並對其穩定性和峰值功率容限做了一些分析。
  19. The holding tank acts as buffer between inputs and output

    貯槽充當的是輸入和輸出之間的緩沖。
  20. Power take - off, shaft drive, blade and slot type. female part

    帶功率輸出軸驅動刀片和槽型.凹形件
分享友人
分享到 Line

分享到臉書