轉矩臂 的英文怎麼說
中文拼音 [zhuǎnjǔbèi]
轉矩臂
英文
torque arm-
By constructing the geometrical model of a certain underground single arm type pantograph and applying the translation of pantograph - head balancing bar and the perpendicular displacement of pantograph in the direction of the movement of locomotive while raising pantograph as the objective which must satisfy the demands of locomotive ' s stable current collection, this paper applied the multi - objective optimization based on the genetic algorithms to design the pantograph mechanism
摘要在建立某地鐵單臂受電弓簡化幾何模型的基礎上，根據列車平穩受流對受電弓提出的各項要求，以受電弓升弓時機車前進方向上的縱向偏移量和弓頭平衡桿的平動為目標，以受電弓正常升弓所需升弓轉矩等為約束，運用基於遺傳演算法的多目標優化技術，對該型受電弓機構進行了優化，得到了使受電弓運動性能達到最優的幾何參數。The content of this thesis comes from the fujian natural science found following research task 。 it studies on a space cantilever single beam attached to a moving support 。 inertia forces which are brought by the support ' s movement ， are acceded to the equivalent initiative forces and the equivalent initiative moments 。 when we consider the relation of the forces and deformation ， we change the method of material mechanical analysis to the elastic mechanical analysis 。 further more ， we discusses the feasibility of the method which uses the multi - rigid - body discrete model to simulate the dynamic characteristic of a elastic body 。 first ， the finite segment method is adopted to establish the models of the beam 。 based on kane ' s equations ， dynamic math - model for the beam are derived 。 and by use of c - language and runge - kutta procedure ， the computer - oriented procedure can give the whole responses of the beam 。 second ， with compare to the numerical examples ， the method which uses the multi - rigid - body discrete model to simulate the dynamic characteristic of a elastic body which is under the condition of movement is verified to be feasible 。
本論文為福建省自然科學基金后續研究課題，以已知支撐運動的單個空間懸臂梁為對象，在等效主動力與等效主動力矩中加入支撐轉動引起的慣性力，並在考慮力與變形關系時，用更一般的彈性力學分析代替材料力學分析，進一步研究用多剛體離散模型來模擬其動力學特性的可行性。首先，用有限段建立機械臂的多剛體離散模型，用kane動力學方法建立其動力學方程。並用c語言編制演算法程序，採用了四階runge - kutta積分程序求解微分方程組，給出構件的全部動態歷程。Torque arm. to reduce wear on packing rings, to enable better sealing and to reduce torque
轉矩臂。有利於減少密封環上的磨損，改善密封性能，減少扭矩。Lower operating torque due to non - rotating stem. torque arm prevents rotation, indicates position and actuates limit switches
由於沒有旋轉閥桿，所以工作扭矩更低。轉距臂防止旋轉，顯示位置和限制開關的啟動。At last, with the stiffness method, the effect of diaphragm density on restraining the distortion of thin - walled bar is analyzed. with different load cases of uniformly load and concentrated load and different boundary conditions of two fixed ends and two simply supported ends and cantilever, the distortion and torsion of the same rectangle thin - walled girder is examined
在均布和集中兩種反對稱荷載情況下，按兩端固定、兩端簡支和懸臂三種不同的支承情況，採用剛度法對同一矩形截面薄壁桿件的畸變和剛性扭轉分別進行分析。分享友人