轉矩試驗 的英文怎麼說

中文拼音 [zhuǎnjǔshìyàn]
轉矩試驗 英文
torque testing
  • 轉 : 轉構詞成分。
  • 矩 : 名詞1. （畫直角或正方形、矩形用的曲尺） carpenter's square; square2. （法度; 規則） rules; regulations 3. [物理學] moment
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 試驗 : trial; experiment; test
  1. Then following reality constituent of engine and connecting component interface, a nonlinear signal cylinder engine model has been created, though fire interval and fire order, a control - oriented four cylinders engine is build. following dynamometer is seen as load, performance of engine is simulated and researched under the condition of constant torque and speed, validation of the math and simulation model have been confirmed by comparison result between simulation with test result of engine performance simulation software dyno

    按照發動機的實際組成，根據各部件的介面類型連接模型庫中的部件，建立了單缸發動機非線性模型，在此基礎上，依據發動機實際發火間隔和順序，建立了面向控制的四缸汽油機模型，並以測功器為負載，通過恆轉矩和恆轉速方式進行了發動機性能模擬和研究，模擬結果和發動機動力性能模擬軟體dyno測試結果的對比驗證了數學模型和模擬模型的正確性。
  2. Regarding the serious smoke ejection of 75 diesel engine series, this paper points out that this problem could be solved by modifying certain parameters and employing gyrating regression design. the actual experiment on 375 diesel engine series shows that, after innovation, the maximum of smoke ejection of gyrating moment falls by 24. 2 percent, and then the rating is demarcated, the smoke ejection falls by 53. 8 percent

    本文針對75系列柴油機排煙嚴重的問題，通過改變噴油嘴及相關調整參數，利用多因素正交旋轉回歸設計安排試驗，取得了較好效果.在375型柴油機上的實驗結果表明：進行優化匹配調整后，最大扭矩點煙度下降24 . 2 ，標定工況時煙度下降53 . 8
  3. Thirdly, the basic configuration plan of a ship undocking assisted by different number of tugs is given. the relationships among the gyroidal moment, gyroidal time and drag forces of tugs in the process of ship undocking are analyzed. the margin of the tugs " towing forces during the ship undocking and turning process is studied

    三、制定了不同數量拖輪協助船舶出塢時的基本布置形式，給出了不同拖輪協助船舶出塢時的拖輪布置示意圖，並試驗分析了船舶出塢回轉力矩與回轉時間和拖輪拖力之間關系，並確定了用於船舶出塢回轉的拖輪拖力的余度大小。
  4. Standard test method for torque - tension relationship of adhesives used on threaded fasteners lubricity

    螺紋緊固件用膠粘劑的轉矩拉力的標準試驗方法
  5. Standard test method for plastic properties of coal by the constant - torque gieseler plastometer

    用恆轉矩gieseler塑性計測試塑性的標準試驗方法
  6. The experiment can obtain the driver and the torsion of the screw propeller of relative speed and is an important method to analyze the efficient part of push

    船模自航試驗可獲得對應航速螺旋槳推力和轉矩，是分析各種推進效率成分的重要手段。
  7. En 28233 thermoplastics valves. torque. test method

    熱塑料制閥門.轉矩.試驗方法
  8. Using the perturbation transfer matrix method as well as the tested data in the laboratory, the 1st and 2nd order perturbed identification of dynamic parameters of the rotor of a boiler pump is made

    摘要利用攝動傳遞矩陣法，結合實驗室的試驗，對某電站鍋爐給水泵轉子的動力學參數進行了一階和二階攝動識別。
  9. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  10. Fin stabilizer is a kind of active stabilizer, which is designed on the principle of torque counteraction. fin stabilizer applied at present is an angle feedback system which calculate the controlling torque through the fin angle. because the relationship between the lift produced by fin and the fin angle is mainly determined by the hydrodynamic experiment, so there are some defects

    目前使用的減搖鰭是一個角度反饋系統，它通過鰭的轉角來計算控制力矩，這樣就存在一些不足之處，因為鰭上產生的升力和鰭角的對應關系主要靠鰭模的水動力試驗來求得。
  11. On the basic theory of transfer heat, tribology of rolling bearings and rotor dynamics, taking gdz48a electrospindle as an example, the paper puts forward the spindle bearing ' s quasi - dynamics analysis model with the influences of the friction heat and preloadings analyzes the friction moment, velocities, contact loads, friction heat and stiffness and studies the influences of the friction heat, structure and application parameters on the speed and dynamics

    本文以傳熱學、滾動軸承摩擦學和轉子動力學為理論基礎，以gdz48a型電主軸為例，建立了考慮摩擦熱和預緊方式影響的主軸軸承擬動力學分析模型，分析了軸承的摩擦力矩、運動、載荷和剛度，研究了軸承的熱特性、設計和應用參數對速度和動力學性能的影響，並進行了試驗驗證。
  12. This research was also supposed to provide a valuable reference for the construction of 500kv eastern hangzhou transformer substation project. to guarantee the rationality of the torsion and bending load application, a set of experimental equipments was transformed from a traditional one by exerting tangential force on the brim of the fan board and conducting broad - billed roller application. in the actually fulfilled experiments on the capabilities of the members under different ratios of torsion and bending, the equipments proved to be well qualified in load applying to large - tonnage members

    試驗中，為保證扭轉及彎矩荷載施加的合理性，在浙江大學工程結構試驗室原有的加載設備的基礎上，分別採用在扇形板邊緣施加切向力和寬軸承滾軸加載的方法，改造並調試出一套可專門用於大噸位構件施加扭轉荷載及組合作用的試驗設備，並利用這套設備進行了離心鋼管混凝土構件在不同彎扭比的組合作用下的試驗研究。
  13. Effectiveness of the proposed control method is verified through simulation

    模擬試驗證明所提出換相轉矩脈動抑制技術的有效性。
  14. Standard test method for determining the drive torque for film and fabric ribbon cartridges

    膠片暗盒和織帶盒傳動轉矩測定的標準試驗方法
  15. The platform can analog rolling and swaying motion of ships. the moment of inertia, damping and restoring force can be adjusted

    該試驗臺架能夠模擬船舶的橫搖運動和橫蕩運動，試驗臺架的轉動慣量、阻尼力矩和恢復力矩可調。
  16. To test the performance of anti - rolling tank more conveniently, the paper sets up the test platform of two freedoms. the platform can analog rolling and swaying motion of ships

    該試驗臺架能夠模擬船舶的橫搖運動和橫蕩運動，試驗臺架的轉動慣量、阻尼力矩和恢復力矩可調。
  17. Standard test method for thermal flow, cure, and behavior properties of pourable thermosetting materials by torque rheometer

    用轉矩流變儀測試可澆注的熱固材料的熱流性固化性及性能特性的標準試驗方法
  18. The experiments show that ultrasonic motors can operate under vacuum condition, but the performance is different from that under general condition, its unloaded speed decreases significantly, while the stall - torque increases a bit

    試驗結果表明，超聲電機可以在真空環境下工作，但性能較常態環境下有所變化，其空載轉速明顯下降，堵轉力矩有所增大。
  19. Thus it is necessary to study moment resistance, rotation stiffness and rotation capacity of the joints. in this paper, six specimens on end - plate composite beam - to - column joints and two specimens on end - plate composite beam - to - column joints were designed to subject to static load. the factors of m - characteristics about semi - rigid composite joints, including bolts, profiled steel sheeting, beam, column, stiffen rib and reinforcement, are studied

    本文設計了6個端板型鋼-混凝土組合樑柱節點與2個端板型純鋼樑柱節點，通過對這些試件的靜力荷載試驗，重點研究了端板型鋼-混凝土組合節點的彎矩-轉角性能的影響因素，包括高強螺栓、壓型鋼板、型鋼梁、型鋼柱、加勁肋，以及混凝土板內縱向鋼筋配筋率等。
  20. Standard test method for comparing metal removal fluids using the tapping torque test machine

    使用攻絲轉矩試驗機比較除金屬流體的標準試驗方法
分享友人
分享到 Line

分享到臉書