轉速值 的英文怎麼說

中文拼音 [zhuǎnsùzhí]
轉速值 英文
rpm level
  • 轉 : 轉構詞成分。
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 轉速 : speed; revolution; rotation rate; speed of revolution; rotating speed; rotational speed轉速指示器...
  1. In pumping fluid with gas, pressure boost can be improved by enhancing the pump rotation speed, thereby improving the performance of the pump to a certain degree ; when the gas content is constant, by increasing the inlet pressure, the pressure boost can be enhanced and the pump efficiency be improved remarkably ; when the gas content is rather high, there will be a problem of matching between the gas pressure and the fluid pressure ; the performance of the multiphase pump can also be improved by means of rational design of buffer vessel and homogenizer

    試驗分析認為，氣液混輸工況下，提高泵轉速可以提高增壓，在一定程度上能改善多相泵的工作性能；含氣率一定時，增加進口壓力，可使多相泵增壓值增大，泵效明顯增加，最大含氣率點后移，但含氣率很高時，存在氣液壓力相匹配問題；改進緩沖罐和均化器的設計，有利於氣液互相夾帶，避免氣囊產生，可改善多相泵的輸送性能。
  2. The series 500 actuators are designed for the entire mid - range of torques and operating speeds

    500系列電動執行機構適用於需要全部扭矩和運轉速度的中間值的場合。
  3. On the basis of this equation, the general differential equations of coupled bending, torsional and pendular nonlinear vibration about rotor with unbalance character and rubbing character are deduced. the bifurcation and chaos behavior especially the influence on bifurcation and chaos behavior of impact and rubbing fault rotor system

    應用數值方法研究了碰摩轉子的彎扭擺耦合振動相應的復雜動力學行為，重點研究了轉子轉速、偏心量等系統參數對碰摩轉子彎扭擺耦合振動的分岔和混沌行為的影響以及扭轉振動和擺動振動對彎曲振動的影響。
  4. The algorithm of svpwm that is adopted by the system implements motor speed - regulation by control of magnitude and phase of motor flux. it can generate less harmonics in the output current of power inverter and less losses of ac motor, reduce pulsant component in output torque and raise availability of dc supply voltage

    系統採用的svpwm演算法通過對空間磁鏈矢量幅值和相位的控制來調節電機轉速，減少了逆變器輸出電流的諧波，降低了脈動轉矩，提高了電壓的利用率。
  5. The controller includes two control loops which are outer speed loop ( variable parameter pi adjustment ) and inner current loop ( single - chop current delta - control ). in order to improve system performances, design of digital control system based on dsp is presented. the proportional parameter and integral parameter can be obtained through the design

    整個系統採用變pi參數轉速調節（外環）與單斬電流滯環調節（內環）相結合的雙閉環控制方式，為了得到既快速又穩定的恆速系統，本文還給出了基於dsp的雙凸極永磁電機數字控制系統的設計方案，通過此設計方案可以得到轉速環的比例參數kp和積分參數ki的參考值。
  6. The results of the experimental tests show that nh4cl and k2hpo4, kh2po4 are the most available nutrents to our isolates when they are degrading oils. the most suitable experinment condition is : temperature being 30 c, initial ph being 7 - 8, the shaking rate of the culture flasks is 180 r / min, the concentration of nacl is 1 %. the biodegradation results have shown that our 6 isolates have the effective degradation capability to crude oil ; within 6 days the transforing rate of oil by each single strain is more than 60 %

    本研究分離出的6株菌，初步鑒定結果為： sy1為微桿菌屬、 sy2為諾卡氏菌屬、 sy3和sy5為假單胞菌屬、 sy4和sy6為芽孢桿菌屬；實驗結果表明， 6菌株的最佳氮源為氯化銨（ nh _ 4cl ） ，最佳磷源為磷酸氫二鉀和磷酸二氫鉀的混合物，最適生長條件為：溫度為30 ，初始ph值為7 8 ，搖床轉速為180r min ，鹽（ nacl ）濃度為1 ；通過降解實驗得出6株菌對原油都有較強的降解能力，單一菌株在5天後的原油降解率都高於60 ， 6株菌對原油的生物降解反應符合一級反應動力學特徵。
  7. According to pump performance curve shown we can get that the distance h is changed with the rotate speed n in the same point q, and the flux q is changed with the rotate speed n in the same point h. from the curve we can get the rule that the distance and rotate speed are in direct with ratio at the same flux point, and the rotate speed and the flux are also in direct with ratio at the same distance point

    根據相似定律：流量與轉速的一次方成正比；揚程與轉速的二次方成正比；功率與轉速的三次方成正比。即在降低轉速，調低水泵出水揚程的同時，功率下降的幅度非常大，從中可以節省相當大的電能。完全應在高水位時降低水泵機組轉速，從而使電機的輸出功率隨著轉速下降值與轉速原值商的三次方關系下降。
  8. Fist ly, use mass equivalent method to predigest the original rotor system. secondly, use transfer matrix arithmetic to have finished the relative program to calculate the critical speed of flexible multi - tray rotor bearing system by matlab language. thirdly. finish program the unbalance response using riccati - transfer matrix arithmetic and finity buck arithmetic. fourthly, answer to the high vibration of uncontroled system when cross the critical speed, come out to adopt changing clearance damper bearing to control the viberation

    本文對多柔盤轉子-支承系統的振動現象做了以下初步探索：用質量離散化方法把原轉子系統簡化；採用matlab語言編制了對傳遞矩陣法計算多柔盤轉子-支承系統的臨界轉速；用matlab語言對riccati傳遞矩陣法和有限元法編制了程序計算系統的不平衡響應；並針對其過臨界轉速時振動較大的現象，提出採用變間隙控制油膜剛度和阻尼，從而使原系統的在特定轉速（臨界轉速）的一段范圍內不平衡響應減小；並從被動控制與主動控制兩方面進行數值模擬，取的了較好的控制效果。
  9. The possible factors including the deviation of temperature in length and breadth of rod, the changes of transfiguration resisting force under the changes of temperature, the adjustment of roll gap, the variation of rolling pressure, the changes of roller speed during dynamic adjusting press, the unmatched of seconds - flux under the dimension fluctuation of the coming sample and so on. the whole system was a closed loop which factors in it interacts each other

    可能的影響因素有:沿軋件縱橫向溫度變化、由溫度引起的軋件變形抗力變化、軋機輥縫值變化、負載變化、電機調節系統由不穩定向穩定過渡過程中軋輥轉速的變化（如咬鋼過程中的動態速降后的回復階段） 、來料尺寸波動造成秒流量不匹配等，整個模擬系統是各個因素相互影響關聯的一個閉環系統。
  10. Part that needs frequency control adopts control technology of computer and universal electromotor and controls the transducer according to the formula that is voltage / frequency = const, which can adjust the speed of electromotor and accordingly control the working condition of ventilator

    變頻調速部分採用計算機和通用電機控制技術的結合，按照電壓與頻率之比等於常值的方式對變頻器進行控制，達到調節電機轉速的目的，從而控制通風機的工況。
  11. The stator of aceg is connected to the grid and the three symmetrical excitation windings in the rotor are fed by converter. the magnitude and frequency and phase and phase sequence of excitation voltage can be controlled, so the magnitude and position of excitation mmf as well as the speed of rotor can be controlled. therefore, acegs have superior performances by contrast with conventional synchronous generators and induction generators, such as upstanding stability, power generation of variable speed constant frequency ( vscf ), adjusting active power and reactive power independently, and absorbing lag reactive power deeply

    交流勵磁發電機的基本結構與繞線式異步電機相同，其定子側接電網，轉子上採用三相對稱分佈的勵磁繞組，由變頻器提供對稱交流電勵磁，且勵磁電壓的幅值大小、頻率、相位、相序都可根據要求加以控制，從而可以控制發電機勵磁磁場大小、相對于轉子的位置和電機的轉速，使得交流勵磁發電機具有良好的穩定性及轉速適應能力、獨立的有功與無功調節能力和較強的進相運行能力，性能超越傳統同步發電機和感應發電機，因而有著廣闊的應用前景。
  12. Compare to other kindred products, besides adjustment of speed, the new calibrater can adjust teeth number and voltage of fanout. the new calibrater can also output a pulse one cycle which simulate cylinder top dead center

    這種標定器與國內外同類產品相比，除了轉速可變外，還有一些創新之處：齒數可調、輸出幅值可調、同時可以輸出每周一個的上死點參考信號。
  13. The software of the system have been compiled on the base of data sampling. the system used double - closed loop and pid method, one loop is speed control, the other is curret control

    系統軟體中，以中斷響應方式，實現電機轉速和電機電流實時採集、處理和控制；通過常數值切換法，實現電機的變結構控制。
  14. Abstract : the responses of shaft bow and their relationships with unbalanceresponses and mechanical or electronic run out are analyzed based on the theory of rotor dynamics. the responses of shaft bow are separated from the unbalance responses successfully by making use of vibration information under different rotor runs. an identification method of thermal bend is presented based on the 2d - holospectrum technique. experimental results show that when bow phase is steady and amplitude is variable, the tangent of initial phase point on the 2d - holospectrum is parallel, which can be effectively used for diagnosis of bent shaft

    文摘:依據轉子動力學理論分析了柔性轉子彎曲響應的特徵，在此基礎上討論了它與不平衡響應及機械與電氣跳動量之間的關系，並利用轉子在不同起車情況下的振動信息，有效地分離了彎曲響應和不平衡響應，求解出彎曲量與不平衡量的比值.提出了轉子在恆定轉速下，基於二維全息譜技術的熱彎曲故障識別方法.研究結果表明，當彎曲量相位穩定而其幅值變化時，轉子響應的二維全息譜初相點的切線是相互平行的，由此可以有效地實現轉子熱彎曲故障的識別與診斷
  15. The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement

    研究結果表明，增大砂輪軸向進給速度和減小工件轉速，採用粗粒度砂輪有利於提高磨削矽片的材料去除率，砂輪軸向進給速度對材料去除率的影響最為顯著；適當增大砂輪轉速，減小砂輪軸向進給速度，採用細粒度砂輪可以減小磨削表面粗糙度；在其它條件一定的情況下，砂輪速度超過一定值會導致材料去除率減小，主軸電機電流急劇增大，表面粗糙度變差；採用比# 2000粒度更細的砂輪磨削時，材料去除率減小，矽片表面粗糙度沒有明顯改善。
  16. The best dosage of dispersant and disperse medium, and the best time of ultrasonic disperse. secondly, the bp neural network process parameters model which describes the relationship between the important process parameters of the preparation of superfine quartz powder and the important evaluate guidelines was built, based on experimentation data. the forecast of the important guidelines was achieved with this model

    其次，本文以試驗數據為基礎，基於bp神經網路建立了球磨法制備超細石英粉體的關鍵工藝參數（轉速，時間，裝樣率，料球比）與粉體的關鍵評價指標（中值粒徑，粗端粒徑，均勻性系數）之間多目標多變量的bp網路工藝參數模型，該模型的建立實現了粉石英制備的關鍵指標預測。
  17. Several characteristic parameters are extracted from the angular velocity curve and the acceleration curve of crankshaft instantaneous rotation, and the quality of them is evaluated by use of the gray relation analysis method and the method for inspecting the consistency of the extremum cylinder number

    在瞬時轉速曲線和角加速度曲線上提取幾個特徵參數，再用灰色關聯度分析方法和極值缸號一致性檢查法對特徵參數的優良性進行評價。
  18. Using method of sumt and powell, the thesis carries out optimization design for air rocket with double - push accelerated velocity and spin - rate regularity, which dramatically decreases air rocket dispersion. in the end, some valuable conclusions are achieved for application

    綜合利用雙推力加速度，轉速規律，同時採用內點罰函數法和powell共軛方向法，對航空火箭彈的主要參數進行優化設計，實現了大幅度減小航空火箭彈散布的目的，得到了一些有應用價值的結論。
  19. The results showed that the color difference was decreased, at the same time, the loss of the soluble protein and amino acid contents were decreased with increase of sample moisture and decrease of barrel temperature ; when increased the revolving speed, the color difference was decreased as a whole meanwhile the contents of soluble protein and amino acid were increased at the beginning and decreased in the end

    結果顯示，提高進料水分，降低機筒溫度，有利於降低擠壓蛋黃粉的色差值，並能減少可溶性蛋白質和氨基酸的損失；螺桿轉速提高，擠壓蛋黃粉的色差值呈總體降低趨勢，而可溶性蛋白和氨基酸的含量呈先提高后降低的趨勢。
  20. In basic action layer ' s designing, it uses a fuzzy - pid control algorithm that brings the system with a good dynamic and static performance. in the whole decision - making process, the protean situation on the competition ground is expressed by an artificial intelligence method for describing the state space that is constituted by selecting a small number of discrete representative states. desired actions are set for every robot based on the tasks of the system and the strategy

    其中在進行基本動作層的設計時，採用了模糊控制與pid控制相結合的智能控制演算法，使系統具有良好的動、靜態品質；而在進行整體決策時，採用了人工智慧的狀態空間表示方法，在比賽場上瞬息萬變的態勢中選擇少量的具有代表性的離散狀態來構成狀態空間，再根據系統需要完成的任務，為機器人確定有限的動作集合，並通過決策推理，給每個機器人選擇合適的動作，從而決策得出機器人的左右輪轉速值，實現對系統的實時控制。
分享友人
分享到 Line

分享到臉書