退火硬度 的英文怎麼說

中文拼音 [tuìhuǒyìngdù]
退火硬度 英文
ammeal hardness
  • 退 : 動詞1 （向後移動） retreat; draw back; move back 2 （使向後移動） cause to move back; remove; wit...
  • 火 : fire
  • 硬 : 形容詞1 （堅硬） hard; stiff; tough 2 （剛強; 堅定; 強硬） strong; firm; tough; obstinate 3 （勉...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 退火 : [冶金學] anneal; annealing; back-out
  • 硬度 : hardness; solidity; scirrhosity （腫瘤的）
  1. The effects of baking temperature, baking time and prestrain on the bake hardenability and dent resistance of isotropic sheet steel and bh sheet steel produced by batch annealing were studied

    摘要研究了烘烤溫度、烘烤時間和預拉伸應變量對罩式爐退火工藝生產的各向同性鋼的烘烤硬化性的影響，並與力學性能相當的冷軋烘烤硬化鋼進行了對比。
  2. The company consists of three workshops, namely cold - rolled steel strip workshop, piping workshop, anode plate of electrostatic precipitator workshop. equipped with a 700 continuous pickling line, a 700 double tandem rolling and three sets of bright annealing furnace with electric tunnel, the cold - rolled steel strip workshop can produce cold - rolled steel strip in sizes of 3506300. 51. 5mm. the workshop is also equipped with a set of 750 slitters and 1000 transverse cutter so as to supply cold - rolled steel sheet, pickling sheet, and hard rolled sheet in different width and length

    冷軋車間裝有一條700連續式酸洗線，一條700二連軋生產線，三組電熱罩式光亮退火爐，可生產3506300 . 51 . 5mm的冷軋光亮帶，並配有一套750縱剪機組和一套1000平整塗油橫切機組，可提供各種寬度和長度的冷軋薄板卷酸洗板卷軋硬板卷。
  3. When the alioa content is increasing, the hardness of composites are also increasing and the temperature at which the hardness obviously reducing are increasing too

    隨著aizo 。含量的提高，復合材料的硬度越高，高溫退火后的硬度明顯降低溫度點也越高。
  4. 5. after high temperature annealing the hardness of the composites did not reduced obviously until 973k, this temperature greatly exceeds that of pure copper ( after cold machining, the temperature is 423k )

    本文制備的材料經高溫退火后的硬度明顯降低溫度點為973k ，大大超過了純銅（冷加工態）的423k ，而且熱穩定性能較好。
  5. S. the composite prepared has excellent heat stability and high - temperature property. during the course of high temperature annealing, the hardness of the composite does not reduce obviously until 973k, while the temperature of pure copper ( after cold machining ) is 423k in the same conditions

    制備的cr _ 2o _ 3 cu復合材料具有良好的熱穩定性及高溫性能，在高溫退火處理過程中，硬度顯著降低點的溫度為973k ，大大高於純銅的硬度降低點。
  6. Annealing could reduce hardness and raise toughness, which could be prone to mechanical machining. quenching and low temperature tempering could raise intensity and hardness of materials, not reduce toughness obviously. quenching on same temperature caused ticp / fe in situ composites having the best integral machine properties

    退火處理使材料的硬度降低，韌性提高，便於機械加工；淬火+低溫回火處理使材料的強度和硬度提高，而韌性無明顯的降低；採用等溫淬火工藝，可使tic _ p fe復合材料具有最好的綜合機械性能。
  7. Effect of annealing process parameters of x45nicrmo4 steel on hardness

    4鋼退火工藝參數對硬度的影響
  8. In view of the higher hardness of high cr - w white cast iron, a lot of experiments were carried out in relation to softening annealing process, and the microstructure transformation during annealing process was analysed

    摘要針對高鉻鎢鑄鐵硬度高這一問題，對其軟化退化工藝進行試驗，並對高鉻鎢鑄鐵退火過程中組織轉變進行分析。
分享友人
分享到 Line

分享到臉書