通信干擾器 的英文怎麼說

中文拼音 [tōngxìngānrǎoqì]
通信干擾器 英文
communication jammer
  • 通 : 通量詞（用於動作）
  • 干 : 干Ⅰ名詞1 （事物的主體或 重要部分） trunk; main part 2 （幹部的簡稱） short for cadre Ⅱ動詞1 （做...
  • 擾 : Ⅰ動詞1 （擾亂; 攪擾） harass; trouble 2 （客套話 因受人款待而表示客氣） trespass on sb s hospital...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 通信 : communication; communicate by letter; correspond
  1. Chapter two is data sample of system. it will discuss the data conversion theory, 24bit e - a data conversion, mux - channel switch sampling technology, and emc design. among them, we will introduce the principle and application of ads 1251, application of photomos technology in mux - channel switch sampling, and emc design with hardware and software of gas feed controller, which has good performance in reliability

    第二章介紹系統的數據採集，該部分包括24bit -采樣原理、多路信號切換採集技術和電磁兼容設計，其中，主要介紹了ads1251晶元的工作原理和應用， photomos技術在多路信號切換采樣中的應用，以及配氣控制器在硬體、軟體等方面所做的電磁兼容設計，通過這些設計使得系統具有很好的穩定性和抗干擾性。
  2. Interference. gps signals are received by the antenna, amplified within the antenna assembly, and then relayed via cable to the oncore receiver module for processing

    這種天線的設計反映了motorola對高標追的追求，即使再有電磁干擾的情況下操作， gps信號通過天線接收，在天線內置放大通過線纜傳輸到oncore接收器上進行數據處理。
  3. For the leakage often occured on condenser brass pipe of hanchuan power plant, using differential inner insert detecting coil the on - line multi - frequency eddy current check technology effectively restrains interferance source signal from support board, etc, improves measuring sensitivity and the measuring result gets more reliable

    摘要針對漢川電廠凝汽器銅管在運行中多次發生泄漏，利用差分內插式檢測線圈，通過多頻渦流檢測技術對凝汽器進行渦流在役檢測，有效地抑制了支撐板等干擾源信號，提高了檢測靈敏度，使得檢測結果更可靠。
  4. The subject derives from electronic equipment bureau of electronic information industry of department of general equipment of china. the subject researches dds ( direct digital frequency synthesizer ) signal source of the frequency agile signal generator. it plays a good role in the important pre - research project that is the test technology of tactics anti - jamming for communication transceiver synthesis

    本課題是總裝備部電子信息部電子裝備局下達的預研項目? ? 《戰術抗干擾通信電臺綜合測試技術》中的信號源部分（捷變頻信號發生器中的dds信號源部分） 。
  5. The automatic identification of the modulation types has been applied to many fields such as source identification, interference identification, radio interception, - electronic countermeasures, etc. the modulation recognizer based on the decision - theoretic approach and the constellation diagram is proposed and the signal ' s kurtosis is used as the indicator to differentiate the analogue modulation from the digital modulation

    通信信號調制類型的自動識別廣泛應用於信號確認、干擾辨識、無線電偵聽、電子對抗和信號監測等領域。本文提出基於決策論與星座圖的綜合調制識別器，使用信號的峰度區分調制類型是模擬調制還是數字調制。
  6. A common data acquisition card can be used on laboratory virtual instrument engineering workbench through designing the external interface between labview and common date acquisition card on the software design ; used the idea of the double buffer and direct memory access, a real time data acquisition and logging about the succession, big capacitance leakage current is realized ; a digital filter is designed to filter high frequency signals

    在軟體設計上，設計了與普通數據採集卡的介面，實現了在labview環境中應用普通數據採集卡的功能；運用雙緩沖和內存直接映射的設計方法實現對連續、大容量泄漏電流信號的實時採集和存儲；設計了數字濾波器對採集后的原始數據濾去高頻干擾。
  7. Through analysising the characteristics of the power system with floating neutral point deeply, the paper puts forward a new plan of single - phase to ground fault line selection on the base of s ' s signal injecton method and gives the hardware and software design. in this design, the high speed sampling and data processing is carried out through using dsp processor ; the large electrice current is drived through the application of a high - performance audio power amplifier and transformer ; the communication between host computer and detectors is realized through rs485 bus technology ; the difference multilevel frequency - selected amplifier is designed and the feeble signal of space is sampled on the base of the theory of magnetic induction ; the interface between dsp and exterior chip and rs485 interface logical is designed through using fpga ; the using of lcd module and keyboard interfacing chip makes the interface between human and machine ; the programme of host computer and detectors is designed through using blocking design method

    在本設計中，採用高速的dsp處理器，實現了對故障特徵信息的高速採集與處理;採用大功率的功放晶元與變壓器配合的方法，實現了大電流信號的驅動輸出;採用485總線技術，組建了裝置主機與多探測器之間的主從式通訊網路，實現了多干擾條件下裝置主機與多探測器的可靠通訊;設計了差分式多級選頻放大電路，採用磁感應的方法實現了對空間微弱信號的接收;利用fpga技術，實現了控制器與多外設的介面及數字信號的串並轉換;採用了先進的lcd液晶顯示模塊及鍵盤介面晶元，設計了人機信息交互的介面;採用了模塊化的軟體設計方法，開發了裝置主機及探測器的軟體程序。
  8. A temporal - spatial filter is designed for noise removing of clinical eeg signals, the first filtering is temporal filtering using band - pass filter, and the second filtering is spatial filtering with ica - based spatial filter

    為了有效去除臨床腦電信號的噪聲和干擾，設計了一種時空濾波器，分兩個階段對腦電信號進行濾波預處理：第一個階段是時域濾波，用傳統的帶通濾波器實現；第二個階段是空域濾波，用基於獨立分量分析（ ica ）的空域濾波器實現。
  9. Rejecting harmonic interference in twacs using iir notch filter based on all - pass filter

    陷波器抑制工頻通信中的諧波干擾
  10. By calculating parameters including the link length, the azimuth angle, the elevation, the optical power that the inter - satellite optical cdma communication system will receive, the variation range of the azimuth angle and the elevation from the optical antenna of atp are understood well. by analyzing the factors to impact bit - error - rate ( ber ) from the received power, multi - user disturbing, background noise, wavelength, bit rate etc, measures to guarantee high performances of the system are obtained, especially those for smoothing the fluctuation of the received optical power from host platform vibration

    分析研究了衛星光cdma通信系統中衛星仰角、方位角和距離，給出了探測器能夠接收到的光功率以及atp子系統捕獲及跟瞄的范圍;對衛星光cdma通信系統性能模型和基於衛星振動系統性能模型的研究，分析了多用戶干擾、接收光功率、背景光噪聲、振動偏差以及碼速率對系統誤碼率的影響，給出了相應的改進措施。
  11. This paper mainly focuses on the noise limiting by means of the direct sequence spread spectrum ( dsss ) and the analysis of the transmission performance of the plc and some digital modulation technology. the contents of the paper is as follows : 1 ) the technical feasibility is proved after simulating noise limiting principle of dsss by means of systemview, the simulation software ; 2 ) a kind of band pass filter ( bpf ) is realized according to the requirement of filter and the principle of butterworth approximation, which satisfies the index of performance of dsss. 3 ) the low voltage plc system includes the sc1128, the specific modulation / demodulation ic, the bpf filter and other circuit components, furthermore, the control function of system is realized by means of the personal computer and the microcontroller

    本課題在對低壓電力線的傳輸特性和數字調制技術進行分析的基礎上，將通信理論中的直接序列擴頻技術（ dsss ）用於解決低壓電力線通信的干擾問題，主要研究內容如下： （ 1 ）用通信模擬軟體systemview對dsss技術的通信和抗干擾原理進行模擬分析，分別對時域和頻域下採用dsss技術前後接收信號的頻譜進行分析，驗證dsss技術在本系統中的可行性； （ 2 ）由dsss技術對濾波系統的要求，根據濾波理論分析了巴特沃思型濾波器的逼近原理並設計了合適的濾波電路； （ 3 ）用調制解調晶元sc1128和自行設計的濾波器加之輔助外圍電路，構造出低壓電力線載波通信系統，並採用atmel公司的單片機設計了接收和發射電路的微控制器； （ 4 ）分別對採取抗干擾措施前後輸入和輸出信號進行對比實驗，並對結果進行分析，驗證了dsss技術對干擾信號的抑制作用。
  12. The criteria for site selection were very strict. because of the sensor s high sensitivity, there should not be electromagnetic interference and building obstructions around the site. there is also the need for appropriate communication lines at the site

    閃電監測站之選址要求嚴格：由於探測儀器非常靈敏，附近不能有電磁噪音干擾，四周必須極少阻擋，並且要有相應的通信線路配合等。
  13. We use equipment covered with dgt approval stickers. we have passed all kinds of their radio licence examinations. we receive and do not transmit, hence no interference

    我們採用貼滿交通部電信總局核準貼子之臺掃:器材，亦考取其各式各樣無線電人員執照。僅接收，未發射，即無干擾。
  14. The paper lays a strong emphasis on discussing the realization of the autocontrol of raster scanning of the scanner in x - y dimension, the " tapping " of the cantilever of the tappingmode afm by a direct digital synthesizer. then a method of parallel communication between dsp and pc in epp mode is given. finally, the author discussed the digital pid closed loop control of the scanner in z - direction, the automatic approaching of the tip using step - motor, and also some electro - magnetic interferences

    論文首先簡單介紹了掃描探針顯微鏡的發展、分類、工作原理及應用；接著對ti公司的tms320vc5402dsp的特點及外圍擴展作了簡單介紹；然後分章節重點講述了利用vc5402dsp實現掃描探針顯微鏡的核心部件? ?壓電陶瓷管的x向和y向的光柵掃描控制；藉助直接數字集成器（ dds ）實現輕敲式原子力顯微鏡的微懸臂的「輕敲」 ； vc5402dsp的主機介面（ hpi ）與pc機在增強并行口（ epp ）模式下的通信；論文最後還介紹了掃描管z向的數字pid閉環控制，步進電機的自動進針，並對實際出現的一些電磁干擾問題作了討論。
  15. In this thesis, first, we present the theory of sess system, the generation of the sess spreading code and its characteristics and the acquisition theory of conventional spread spectrum communication system. an efficient acquisition scheme based on periodically transmitting the synchronization head, which is composed of binary chaotic codes, using the matched filter and automatic decision threshold - level control based on a so - called constant false alarm criterion for sess system is present. the acquisition model of sess system is built and simulated in the awgn channel, the raleigh fading channel and imulti - address interfere condition

    本文首先概述了自編碼擴頻通信的原理、自編碼擴頻序列的產生方法及其特性和擴頻通信系統編碼同步的理論，然後針對自編碼擴頻通信系統提出了擴頻序列捕獲方案:周期性地加入混沌序列同步碼，並採用恆虛警率匹配濾波器捕獲法;在加性白高斯噪聲通道、瑞利衰落通道和多址干擾情況下進行了模擬，分析了各種捕獲性能:在選擇性能最優的混沌序列、適當的序列長度、虛警概率及門限值的情況下，可以獲得較短的捕獲時間和較大的捕獲概率。
  16. In the system, the low voltage power line is the first signal tunnel without any other relay equipments between customer terminal and substation collector, public telephone line serves as the second signal tunnel between substation and management center computer. as a breakthrough of conventional concept of electricity meter, this thesis initiate a new concept, namely, intelligent power customer terminal ( shortly, customer terminal ), which is developed with spread spectrum plc communication functional and possesses many advanced functions, such as, in addition to electric energy acquisition, guarding against electricity pilfering, preventing wrong connection, protecting malfunction, remote communication ( for example, remote power supply or halt, remote configuration of electricity meter, remote load control, etc ), and so on

    本文首先系統地總結了目前國內外低壓電力網數據傳輸技術的研究現狀和存在的問題，在此基礎上，從理論上論證了在低壓電網上應用擴頻載波數據通信技術的可行性和優越性，並重點論述了擴頻載波技術抗電力線噪聲干擾的機埋；本文提出了一個新穎的基於低壓電力線擴頻載波通信技術的集中遠抄系統的總體方案，即由用戶終端、集中器和電能管理系統所組成的網路系統，其中，用戶終端到配變集中器用低壓電力線作為通道，中間無需其他硬體中繼設備，集中器到電能管理系統用公用電話網作為通道。
  17. Thirdly, the range switch circuit and filter circuit are designed in the analog input channel. to realize the safe high speed acquisition, the interface circuits are separated from the function circuits, and the isolation power with high performance and digital isolator is used to restrain the common mode disturb and noise of the input

    3 .模擬輸入通道設計有量程切換電路和濾波電路，並且採用了屏蔽、浮置技術和磁耦隔離技術，使用了高性能的隔離電源和磁電耦合器，有效地抑制了輸入信號的共模干擾和噪聲，實現了安全、高速的數據採集。
  18. Through some research in depth on soct, this thesis proposes a scheme of star - type vsat ( very small aperture terminal ) network based on overlap back transmission, and do some research on key techniques involved with the scheme and their partial realization with fpga ( field programmable gate array ), such as spread spectrum techniques, a non - coherent de - spreading spectrum and demodulation technique and adaptive interference cancel

    本文在深入研究衛星重疊通信技術的基礎上，提出了一種基於重疊回傳的星形vsat網方案。並在衛星重疊通信涉及的幾種關鍵技術及其部分核心器件的fpga實現等方面進行了一些研究，包括：擴頻技術、非相干解擴解調技術、自適應干擾抵消技術等，並將它們用於基於重疊回傳的星形vsat網方案。
  19. Based on whole design, this essay adopts gps technology to make the key component in taximeter - orientation module, compiles corresponding software, and makes adjustment and experiment. also it has done a profound research in district - identification arithmetic, that is improved radian arithmetic, and it is verified by matlab. we adopt anti - interference measures in both hardware and software to ensure communication reliability and working stability

    在確定總體設計方案的基礎上，本文採用gps技術研製具有區域識別功能出租車計價器中的關鍵部件? ?定位模塊，編制了相應的運行軟體，並進行了調試和試運行試驗；對區域識別演算法進行了深入研究，提出了區域識別的演算法?改進弧長法，並運用matlab軟體進行了演算法驗證；為了保證通信的可靠性和工作的穩定性，從軟、硬體兩個方面採取了抗干擾措施。
  20. ( 2 ) the disturbances are analyzed which are caused when signals with a few work frequencies are inputted. and the influence in the realization are also discussed such as calculation period and the quality of multibeamforming. they are solved by software and hardware methods - array processing with multiple dsp and low - passed re - filter

    （ 2 ）根據本系統的多個工作頻率的特點，分析了各個工作頻率的輸入信號波束形成時造成相互干擾，以及對波束形成演算法的影響（如在dsp處理器中的實現的運算量、波束結果的質量等） ，提出相應的軟體和硬體解決方案? ?多dsp陣列處理和二次低通濾波，並進行了理論模擬。
分享友人
分享到 Line

分享到臉書