通信操作指令 的英文怎麼說

中文拼音 [tōngxìncāozuòzhǐlìng]
通信操作指令 英文
coi communications operating instructions
  • 通 : 通量詞（用於動作）
  • 操 : Ⅰ動詞1 （抓在手裡; 拿; 掌握） hold; grasp 2 （做; 從事） act; do; operate 3 （用某種語言、方言說...
  • 指 : 指構詞成分。
  • 通信 : communication; communicate by letter; correspond
  • 操作 : 1 （按照一定的程序和技術要求進行活動） operate; manipulate; handle 2 （所進行的若干連續生產活動的...
  • 指令 : 1 （指示; 命令） instruct; order; direct2 （上級機關對下級機關的指示） instructions; order; direc...
  1. About two - thirds of scientists read operating instructions in english and three - quarters of the worlds correspondence are written in this language

    全球大概有三分之二的科學家閱讀以英文書寫的操作指令，同時世界上四分之三的通信語言也是英語。
  2. Before the connectting between moden and other equipments, it works at the cammand mode, the cammand that is send to moden is used to set or manipulate the mode, after the connectting between moden and other equipments, it works at connectting mode, at that time, the cammand send from the computer is send to another computer which will pass the moden and telephone line. the moden control cammand is called " at " cammand, all the control manipulation is realized by sending the ascii character to moden, after the moden received the " at " cammand, it firstly judges the cammand, secondly, it analyses and executes the cammand, finnally, it executes a response by sending back a ascii character, during the deseign of below - computer, we introduce in detail the deseign of system hardware and system software, below - computer system hardware and system software, below - computer is made up of microchip collecting and controlling system, which finish the strobe and water level data collection, display and disposal, deal with the communication with the above - computer, the microchip is the centre of data dealing with, the peripheral equipments are made up of data collecttion module, control cammand input module, display module, execute output module, and long - distance communication module

    在moden控制軟體的設計中，詳細敘述了moden正常工作時的幾個重要函數：初始化函數、撥號處理函數、應答處理函數、掛機處理函數，設計並調試了四個函數的通信程序，數據機工作時存在兩種模式，命令模式與連線模式，命令模式是針對功能設置的模式，連線模式是數據傳輸的模式。當數據機未與其他設備連接時，其處于命令模式，這時候下達給數據機的指令是作為數據機本身設置或操作用的；當數據機已經與其他設備連接時，其處于連線模式，所有在此時由計算機送至數據機的信息都將經由電話線傳送到另一部計算機上。專門使用於控制數據機的指令集被稱為「 at指令集」 ，對moden的所有操作（如撥號、應答、掛機等）都可以通過給moden發送ascii字元串來實現， moden在收到at命令后，先對命令進行判斷，接著分析和執行命令緩沖區中的命令，最後以自身的ascii字元對命令作出響應。
  3. In communication system software ( such as ibm ' s acf / vtam ), pertaining to a resource that has not been activated or has not been deactivated by a ( vtam ) operator command

    在通信系統軟體（如ibm的acf / vtam ）中，指沒有通過通信系統操作員命令激活或釋放的資源。
  4. The video phone system designed by us is mainly the real - time implement of a - v codec the implement of h. 323 protocol stack and the implement of the network communication protocol for example pppoe smtp and pop3 etc. so we not only ensure that the qos of the a - v codec ' s datum, but also develop the increment services for example e - mail system and browser etc. the paper will emphasis on the graft and realization of the internet protocols h. 263 video codec rate control algorithms for video encoder and optimization methods of the codec based on tm1300. h. 323 sip, h. 264 and psos + are also simply introduced

    本文主要針對作者在實現ip可視電話系統中所從事的研究工作而展開的，將重點放在ip可視電話系統中tcp ip協議棧在psos +上的移植、網路通信協議如pppoe 、 ppp 、 smtp 、 imap 、 pop3 、 dns 、 dhcp等協議的實現、 h . 263視頻編碼及其碼率控制演算法研究、視頻編碼中基於程序結構和7m1300dsp專用指令的優化方法，同時初步介紹h . 323 、 sip 、 h . 264及嵌入式系統中的實時操作系統（ rtos ） psos + 。
分享友人
分享到 Line

分享到臉書