通用噴嘴 的英文怎麼說

中文拼音 [tōngyòngpēnzuǐ]
通用噴嘴 英文
all-purpose nozzle
  • 通 : 通量詞（用於動作）
  • 用 : Ⅰ動詞1 （使用） use; employ; apply 2 （多用於否定: 需要） need 3 （敬辭: 吃; 喝） eat; drink Ⅱ名...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 通用 : be in common use; be current; apply or be used universally
  1. This paper deriving the theory work inflection point in the static stage characteristics curve of small measurement range linear dimension measurement. by the way of high pressure and back pressure pneumatic measure and designed the parameter of the mainly and measure spray head, which are the key component in the spray head - baffle pneumatic sensor. the different groups for the main - spray head and the measure spray head, will effect the dynamic and static stage characteristic parameter. the author have done contrast experiment and optimization design to test and verify the theory derivation whereby made the rang of show valve of pneumatic measure system measure range up to 40 u m, the sensitivity up to 100mv / u m, resolution up to 0. 05 p m, the uncertainly of measure is less than 0. o2 u m, satisfaction of requirement of groups the carboy hatch thickness size precise measure of soft shims

    對高壓背壓式氣動測量用於小量程線性尺寸測量的靜態特性曲線的理論工作拐點進行了推導，對氣動測量系統中的噴嘴-擋板型氣動傳感器中的關鍵部件? ?主噴嘴和測量噴嘴的參數進行了理論設計，對主噴嘴和測量噴嘴的不同組合，將影響測量系統靜、動態特性指標的噴嘴參數進行了對比實驗和優化設計，並通過實驗驗證了理論推導，從而使氣動測量系統量程的示值范圍達到40 m ，靈敏度達到100mv m ，解析度達到0 . 05 m ，測量不確定度小於0 . 2 m ，滿足了壓縮機缸蓋軟體墊片厚度尺寸精密測量分組的要求。
  2. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  3. Regarding the serious smoke ejection of 75 diesel engine series, this paper points out that this problem could be solved by modifying certain parameters and employing gyrating regression design. the actual experiment on 375 diesel engine series shows that, after innovation, the maximum of smoke ejection of gyrating moment falls by 24. 2 percent, and then the rating is demarcated, the smoke ejection falls by 53. 8 percent

    本文針對75系列柴油機排煙嚴重的問題，通過改變噴油嘴及相關調整參數，利用多因素正交旋轉回歸設計安排試驗，取得了較好效果.在375型柴油機上的實驗結果表明：進行優化匹配調整后，最大扭矩點煙度下降24 . 2 ，標定工況時煙度下降53 . 8
  4. G ) the convertion of si 1126 data into ktva input data file : ktva ' s values, definition, unit and format are tested many times. h ) the result of simulation computation is visualized and analyzed, i ) the study on sll 126 parameters ; by altering the ajustment data, their performance changes are studied

    本文首次應用kiva模擬平臺，對s11126柴油機進行了模擬；通過主要參數（噴油量、轉速、噴嘴安裝高度等）的改變，分別計算出多項主要性能指標曲線和圖形，並對其進行分析，從而總結出以上參數的改變對性能的影響，驗證了kiva模擬平臺的強大功能。
  5. It can change adhesive ' s placement via change spray nozzle, such as dot type, single line, multi - line type, spiral type

    通過噴嘴的更換可實現、點狀、條狀、多條狀、螺旋狀等不同類型施膠的應用。
  6. Through the controls of geometric dimension of micro - nozzle and driving frequency to obtain the volume of droplets in the grade of pico to femto litre, which is applicable to make high density micro - array

    通過微噴嘴幾何尺寸控制和驅動頻率控制獲得從飛升到皮升級樣點體積，可以用於製作高密度的微陣列。
  7. Based on the analysis of the combustion in cylinder, the thorough research of multiparameters ( engine speed, load, ignition timing, injection timing, injection nozzle type, compression, ignition pattern etc. ) on methanol engine combustion cyclic variations is made on a 1130 single - cylinder diesel engine fueled with methanol

    在燃用甲醇燃料的1130單缸柴油機上，通過缸內燃燒分析，對影響甲醇發動機循環變動的各種因素（轉速、負荷、點火提前角、噴油提前角、噴油嘴類型、壓縮比、點火方式等）進行了詳細的研究。
  8. 1 washers shall be color coded at hose nozzle outlets and mounted inside the fume hood and controlled from the exterior with color - coded index handles

    水龍頭在噴嘴處用顏色標示，並安裝在通風櫃內部。其控制開關在通風櫃外面，用不同顏色標示把手。
  9. The polyamide to easy generation salivate ( pa ), through choosing form of a powerful person hot nozzle also can realize hot flow path to shape

    對易產生流涎的聚酰胺（ pa ） ，通過選用閥式熱噴嘴也能實現熱流道成型。
  10. As to the work about experiment study, at first, the paper makes certain the prominent affecting factors to the automating and humidifying property of this kind of nozzle by orthogonal experiment. by jicha analysis method and fangcha analysis method, the paper got that the nozzle aperture, the initial water temperature and the spraying pressure have prominent effect to the humidifying property while the effect of the original air state is small

    試驗工作方面，首先通過正交試驗確定對撞針型高壓小孔徑離心式噴嘴霧化加濕性能影響顯著的因素，運用極差分析法和方差分析法，得到噴嘴孔徑、噴水初溫和噴水壓力對噴嘴的加濕性能影響顯著，而待加濕空氣初狀態的影響相對較小。
  11. Later, the paper ascertains how the prominent factors influence the humidifying effect by single factor experiment and got such solutions : when other situations do n ' t change, the nozzle flux will enhance with the increase of the nozzle aperture and spraying pressure. air ' s changing quantity of enthalpy and absolute humid, valid humidified quantity, humidifying efficiency and saturation efficiency will enhance with the increase of the initial water temperature. with the enhance of the praying pressure, the valid humidified quantity and air ' s changing quantity of enthalpy will increase first and decrease later, while the humidifying efficiency will drop

    然後通過單因素試驗確定影響顯著的因素如何作用加濕效果，得到：在其他條件不變的情況下，噴嘴流量隨噴嘴孔徑和噴水壓力的升高而增大，空氣焓變量、絕對濕度差、有效加濕量、加濕效率及飽和效率隨噴水初溫的升高而提高，有效加濕量和空氣焓變量隨噴水壓力的升高先增加然後有所下降，而加濕效率隨噴水壓力的升高而下降，焓變量和絕對濕度差隨水氣比的增加而增大。
  12. General specification for the water nozzle to control dusts in coal mine

    煤礦降塵用噴嘴通用技術條件
  13. It came true to take advantage of transfer standard to compare and analyze the naturalgas standards of measurement on site. the dissertation used the transfer standards to take the site comparative experiments to the sonic nozzle standard measurement of the nation crude oil great flux measure station carried by vehicle and the standard measurement of the general pertrifaction plant. it evaluated and analyzed the measure capability of these two standards, thus to keep them fulfilling the rules of the verification and the regulations of relative criterions

    本文通過使用傳遞標準，對國家原油大流量計量站車裝音速噴嘴標準裝置和大慶石化總廠計量站氣體計量標準裝置進行現場比對試驗，對這兩項天然氣計量傳遞標準裝置的計量性能進行了評價和分析，使國家站和大慶石化的天然氣流量計量標準裝置達到了檢定規程和相關標準的規定要求。
  14. The spray processes of throttling and normal pintle nozzles are investigated in this paper. the test results show that the better spray characteristics and spray quality can be achieved when the throttling pintle nozzle is used in small diesel engines

    本文對節流軸針式和普通軸針式噴油嘴的噴油過程進行實驗研究，試驗結果表明，節流軸針式噴油嘴應用在小缸徑柴油機上能取得良好的噴油特性和噴霧質量。
  15. Using compressed air and transformer oil as working substance, this paper studied the pressure characteristic of internal - mixing nozzle and acquired the experimental relation on the pressure in the mixing chamber of internal - mixing nozzle against the operation parameters and structure parameters according to the method of step by step regression

    摘要以壓縮空氣和變壓器油為工質對內混式介質霧化油噴嘴的流量特性進行實驗研究，並通過逐步回歸分析的方法獲得了內混式介質霧化噴嘴油、氣流量系數與運行及結構參數的實驗關系式，可供設計使用部門參考。
  16. This type of dryer was fitful for liquid drying in concurrent, counter - current or mixed air - flow. the dryer can produce powders, granules, hollow spherical particles and agglomerates products. the spraying capacity and particle size were changed by altering the parts assembled in the nozzle

    壓力噴霧乾燥裝置其霧化器的結構適用易調，可通過改變噴嘴的內部結構得到所需要的噴液量和霧滴尺寸，目前該型式乾燥機已推廣應用於食品、化工、醫藥、建材、環保等行業。
  17. In this dissertation, the author summed up the muti - technique in fluid dynamics, heat and mass transferring, mechanical designing and computational technique and studied the conventional pressure spray dryers with different air disperse structure and outlet equipment, at last put forward the theme i. e. the study on combined spin - flow pressure spray drying technology, the main contents were as follows : ( 1 ) the combined spin - flow pressure nozzle was designed whose novel structure has no report at present, and the structural designing parameters were obtained through analyzing the physical characteristic of materials and distribution of particles

    本文總結了國內外在壓力噴霧乾燥裝置的研究應用狀況，並分析了現有噴霧乾燥裝置設計方面的優缺點，運用流體力學、空氣動力學、傳熱傳質學、機械設計和計算機技術等多學科知識，綜合研究了傳統壓力噴霧乾燥系統的單噴嘴霧化裝置在併流、逆流以及混流乾燥中的應用和噴霧乾燥塔的不同布風裝置以及出風裝置的設置情況等，提出了新型旋流式組合壓力噴霧乾燥技術並對此進行了研究，其主要內容包括： （ 1 ）本文創造性地設計出旋流式組合壓力噴嘴的基本結構，並通過對料液的物化特性研究分析以及顆粒度的分佈要求，給出了噴嘴的不同結構設計參數。
  18. The present research and practical indicated that the effervescent atomizer may obtain the good atomization effect in the small alr situation, compares with the ordinary machinery and the medium spray nozzle, has the merits of saving the fuel, reducing pollution and so on, has the broad application prospect

    目前的研究及實用表明，氣泡霧化噴嘴可以在小氣液質量流量比情況下獲得較好的霧化效果，與普通的機械和介質霧化噴嘴相比，有節約燃料，減少污染等優點，具有廣闊的應用前景。
分享友人
分享到 Line

分享到臉書