速度場 的英文怎麼說

中文拼音 [sùdùchǎng]
速度場 英文
velocity fields
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 場 : 場Ⅰ名詞1 （平坦的空地 多用來翻曬糧食 碾軋穀物） a level open space; threshing ground 2 [方言] （...
  • 速度 : 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. （快慢的程度） speed; rate; pace; tempo
  1. The velocity field has been designed in this article on defect of rolling workpiece surface about cross wedge rolling technique in the process of forming axial symmetry spare parts by result of simulated experiment of consult document [ 4 ]

    摘要依據文獻[ 4 ]的模擬實驗結果，擬定了楔橫軋工藝成形階梯軸類件時軋件表面出現表面缺陷（蛇皮狀或魚鱗狀缺陷）時的金屬流動速度場。
  2. The influence of inflow velocity, the baffle body height and the clapboard position on the flow velocity, flow equilibrium between the two sides of the clapboard, particle distribution, rich / lean concentration ratio and flow resistance characteristic are studied numerically

    文章研究了來流速度，撞擊塊高度、隔板位置等因素對氣相速度場、隔板兩側配風均勻性、顆粒濃度、濃淡分離比和燃燒器內阻力特性的影響。
  3. In this paper, using phoenics software to compute and analyze the variety rule of the convecting transfer heat at the basis of computing and analyzing the temperature and velocity field of one underfloor supply air room with a focus hot source, and concluding that the number of the hot source and the supply air outlet > the intensity of the hot source and the volume of supply air will influence convecting transfer heat, and obtained its correlativity formula

    本文針對一下部有集中熱源的地板送風空調小室，利用phoenics軟體，在計算分析小室內氣流的速度場及溫度場的基礎上，對對流熱轉移量的變化規律做了計算分析，最後得出對于下送風小室的對流熱轉移量與熱源的個數、送風口個數、熱源強度、送風量等因素有關，並且得出了其相關關系式。
  4. Present - day crustal movement speed field of ch

    網研究中國大陸塊體現今地殼運動速度場
  5. Firstly, simulate flow field of rear smoke channel, plot velocity magnitude and ash concentration distribution in section of entry of heat pipe air preheater, compare with data which were measured in guiyang power station, verify simulation to be reasonable and right. secondly, simulate all kinds of factors which affect flow field ' s uniformity such as length, thickness, location of diffluent board, ash concentration, ash diameter, and so on, find the chiefly factors. thirdly, install guide board in curve channel in rear smoke channel, then simulate its " flow field, plot velocity magnitude and ash concentration distribution

    在此基礎上模擬在冬夏兩季不同情況下，不同流速對熱管空氣預熱器壁面溫度的影響；然後對影響整個流場分佈的各種因素：包括分流板長度、厚度、偏離中心流道位置的偏離度、飛灰濃度、飛灰粒徑等因素進行數值模擬；最後提出在分流煙道轉彎處加裝導流板，並模擬加裝導流板后的流場分佈，得到下級空氣預熱器出口、熱管空氣預熱器進口處的斷面速度場分佈、濃度場分佈，以論證加裝導流板能達到流場均勻化的作用。
  6. Simulates and analyses the velocity and temperature fields inside the external respiration double skin facade of a building

    摘要對某建築外呼吸雙層通風玻璃幕墻內的速度場和溫度場進行了模擬分析。
  7. The simulation result showed that : variety of impact acceleration field has great influence on lower extremity injuries ; using safety belt has prominent efficiency to reduce lower extremity injuries ; using knee bolster with lower stiffness can reduce the loads to femur, knee and tibia ; the right foot placed on the brake pedal will increase the risk of foot injury evidently ; variety of footwell intrusion induced by impact deform of car forepart will influence lower extremity injuries severity to a certain degree

    模擬結果表明:加速度場的改變對下肢損傷有非常大的影響;佩戴安全帶對降低下肢損傷風險有顯著的作用;膝墊採用較低剛度的材料可以較好地降低大腿，膝部以及脛骨的受力和損傷;右腳放在剎車踏板上會使得右腳損傷風險明顯加大;車體前部碰撞變形產生的腳艙侵入量對人體下肢的損傷會產生一定的影響。
  8. In this paper, the microbus " s temperature field and velocity field is researched through numerical simulation and experiment for the first time

    本文首次採用數值計算和試驗相結合的方法對微型麵包車車室內溫度場、速度場進行了研究。
  9. Experimental study on two - phase velocity field in counter - flow spray saturator

    逆流噴霧式飽和器內兩相速度場的實驗研究
  10. The typical velocity field and the pressure on the step surface of the stepped spillway are measured using the laser doppler anemometer and the piezometer tube respectively

    採用多普勒激光測速儀和測壓管分別對階梯溢流壩面典型速度場和階梯表面壓力進行詳細測量。
  11. First, in order to verify the correct of this retrieval month, by using the data of three - dimensional wind field, raininess field and temperature field that are output by mm5 numerical simulation, we climate the radial velocity field and echo intention field in the in - phase observation area of dual - doppler radar, then, on the base of the upwards retrieval theory and using the radial velocity field and echo intention field in the in - phase observation area of dual - doppler radar, we retrieve the atmospheric three - dimensional wind field

    首先，為檢驗此種反演方法的可靠性，我們使用mm5數值模式輸出的三維風場、雨強場、溫度場等數據，分別模擬生成兩部雷達同步觀測區的徑向速度場和回波強度場，然後根據以上的反演理論利用模擬的雙多普勒天氣雷達觀測到的徑向速度場和回波強度場反演出大氣三維風場。
  12. Some conclusions are drawn : 1 ) effect of inertial force from superstructures on the lateral seismic response of single pile can not be ignored ; 2 ) the lateral seismic response of single pile induced by far - field earthquake are mainly affected by acceleration mass of superstructure > site eigenperiod. it increases with the increment of accele ration and mass of superstructure. as the site characteristic frequency approaches the self - oscillation frequency of the pile, sympathetic vibration occurs and the value of lateral seismic response reaches maximum ; 3 ) as the stiffness ratio of pile to soil increase, the relative displacement of pile to soil increases ; 4 ) the lateral seismic response of fixed - head pile is much smaller than that of free - head pile

    將其解析解與具體的的抗震設防烈度和場地特徵周期結合起來，計算分析了成層地基中單樁的橫向地震響應，得到了以下結論： 1 ）上部結構慣性力對樁的橫向地震響應的影響不可忽略； 2 ）成層地基中的單樁的橫向地震響應主要受地震基本加速度、場地特徵周期、上部結構質量的影響，隨地震基本加速度、上部結構質量的增大而增大；場地特徵頻率越接近樁基自振頻率，樁基地震響應越大，等於自振頻率時，由於發生共振現象，樁基響應幅值最大； 3 ）樁土剛度比越大，樁土之間的相對位移的幅值越大； 4 ）樁頂固接的連接方式，可以有效地降低地震時單樁的橫向地震響應。
  13. In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production

    論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。
  14. The viscosity of the fluid has no direct effect on the velocity profile.

    流體的粘度對速度場沒有直接影響。
  15. Velocity field in ship waves on the viscous fluid

    在粘性流體中船行波的速度場
  16. Cfx software is used to simulate flow fields of water cushion pool. contour stream line, vortex and kinetic energy in water cushion pool are found and offered as visualization form. the results of numerical simulation and piv are analyzed and compared in this paper

    使用數值軟體（ cfx ）對此水工實驗模型的淹沒射流流場進行了數值模擬，得到水墊塘內的速度場、等流函數線圖，將這些計算結果以可視化結果的形式給出。
  17. Air is entrained as water jetting into water cushion pool, the gas - liquid two phase flows field are formed. the every phase velocity field are measured by using piv and ptv ( particle tracking velocimetry ) method in the course of jet angle 75and60 in gas - liquid flows of water cushion pool. image house of two phase flows are set up

    西安理工大學碩士學位論文使用數字圖像處理技術中的piv和ptv測速技術就射流入水角75度和60度兩種情況分別測量了水墊塘模型水氣兩相流流場的各相速度場，建立了相應的兩相流流態圖像庫。
  18. Using the post processing tools of this cfd software, this article analyses the temperature and velocity field in the vav air - conditioned office and finally evaluates the indoor air distribution, adopting air diffusion performance index ( adpi )

    利用cfd軟體的后處理工具對不同送風方式以及不同工況下的變風量空調室內的溫度場和速度場進行了分析，最後採用空氣分佈特性指標對空調室內的氣流組織進行了綜合評價。
  19. By means of analytical methods based on upper bound element technique ( ubet ), non - axisymmetric element, simulates the forming process of non - axisymmetric involute teeth spline has been introduced, formula of speed fields been derived and the deformation regularity of steady extrusion on the forming process successly described

    摘要本文運用上限單元技術（ ubet ） ，引入非完全軸對稱單元，模擬了非完全軸對稱零件漸開線齒外花鍵的成形過程，推導出了成形過程中的速度場公式，並成功地描述了擠壓過程中的變形規律。
  20. The research aims at the demonstration and the mend of the design on the new purifier and presents a calculation method for solving the two - phase flow in fluid machine by the finite element method. after analyzing the two - phase flow in the new purifier by means of the continuum model, poisson equation, navier - stokes equation and continuous equation are derived and solved by using the finite element method. the solution on pressure, velocity and particle concentration simulates the departure well between oil and water, which proves the accuracy of the design on the new purifier

    本文採用兩相流連續介質模型，由兩相分離流動理論得到控制方程，採用chorin的直接速度-壓力mac法的思路，對新型油水分離裝置內油水兩相流動作了細致的分析，同時首次把科氏慣性力引入兩相流模型中，進行分析和計算，將研究擴展到三維，並用有限元法分別解poisson方程、 n - s方程、連續方程的方法，對流場內壓力場、速度場、濃度場進行了分析和計算，較好地模擬了新型油水分離裝置內油水分離的現象，證明了設計方案的正確性。
分享友人
分享到 Line

分享到臉書