進口溫度 的英文怎麼說

中文拼音 [jìnkǒuwēndù]
進口溫度 英文
entry temperature
  • 進 : 進構詞成分。
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 進口 : 1 （船隻進港） enter port; sail into a port2 （外貿進口） import3 （入口） entrance; [機械工程] i...
  • 溫度 : [物理學] temperature
  1. Experimental studies on s1a - 02 gas turbine with water injection into compressor interstage / inlet as well as that on turbocharger self - loop test rig with inlet water injection are introduced. test results are in good accordance with simulation results, wet compression can lower compression work and increase engine power output so engine performance is enhanced, if engine power output is not changed, efficiencies of compressor and this engine become higher and turbine inlet temperature and fuel consumption become lower and if keeping t4 the same as that before wet compression is used, efficiencies become furthermore higher and engine power output increases greatly

    實驗結果和計算結果同樣表明：濕壓縮減少了壓氣機所消耗的壓縮功，增加了燃氣輪機的輸出功率，提高了燃氣輪機性能，如果保持發動機輸出功率恆定，濕壓縮可以提高壓氣機和整個燃氣輪機機組的效率，與此同時，渦輪進口溫度t _ 3 ~ *和燃油消耗率下降；如果保持渦輪排氣溫度t _ 4 ~ *恆定，壓氣機和燃氣輪機機組效率進一步提高，燃氣輪機輸出功率增加。
  2. Thermometer for fresh water inlet

    淡水進口溫度計
  3. This paper facous on the micro - computer control of the burning furnace system. taking to meet the requirements of the user ' s as basis, it is designed about computer in hardware and software it brings forward a scheme of intelligent & fuzzy - control based on 8098 single - chip micro - computer to get the best proportion of fuel oil and burning air, to realize the auto - contral of the temperature of flue gas in or out the burning furnace. so the accurate efficiency is received, this can ensure the ahf unit having a high production and low costs and energy

    在控制上以滿足新爐型的設計要求為基礎，進行了微機控制的硬體與軟體開發，提出了採用8098單片機進行模糊智能控制的設計方案，實現了燃料油與燃燒空氣最佳比例控制、燃燒爐出口煙氣溫度控制、燃燒爐進口煙氣溫度控制和安全聯鎖報警控制，提高了燃燒爐出口溫度的控制精度和燃料使用效率，為整個裝置提高產量和降低消耗提供可靠的保證。
  4. In this paper, the sensibility analysis of the factors affecting the temperature in well bore is relatively systematically made by using a large number of the data calculated with the borehole flow and heat transfer 3 ? d numerical model proposed by the author. the study shows that the thermophysical parameters of the drilling fluid and formation, etc. and the entrance temperature and circulating capacity, etc. of drilling fluid have a greater influence on the temperature in well bore. therefore, accurately mastering the thermophysical parameter values of penetrated formation and drilling fluid in well bore, considering the influence of the temperature and pressure on thermophysical parameters and accurately measuring such parameters as entrance temperature and discharge capacity of drilling fluid, etc. are of utmost importance for accurately simulating the temperature in well bore

    利用由作者提出的井內流動和傳熱的三維數值模型計算所得的大量數據，文章對影響井內溫度的諸多因素進行了較系統的敏感性分析，研究表明：鉆井液和地層等的熱物理參數以及鉆井液的入口溫度、循環排量等對井內溫度有較大影響，因此，準確掌握所鉆地區地層和井內鉆井液的熱物理參數值，考慮溫度壓力對熱物理參數的影響，準確測量鉆井液的入口溫度、排量等參數值，對于井內溫度的準確模擬至關重要。
  5. Influence of inlet temperature of cold media on ice - forming processes outside pipes

    冷媒進口溫度對管外結冰過程的影響
  6. The blade inner channel cooling is very important in the design of turbine blade, with the ever - increasing inlet temperature, the new heat transfer enhancement structures of higher performance are demanded. because of the complexity of the flow and heat transfer of the blade inner channel cooling, the numerical modulation is superior to the experiment. this thesis studied the blade inner channel cooling with the method of numerical modulation

    葉片內部通道冷卻在航空發動機葉片的設計中佔有重要的位置，航空發動機進口溫度的增高對其提出了更高的要求。由於葉片內部通道冷卻的流動與傳熱的復雜性，數值模擬較實驗的研究方法有其優越性，本文利用數值模擬的方法對葉片內部通道冷卻進行了研究。
  7. To improve the purity of carbon dioxide from the purifying column, a nonlinear model was established for describing the relationship between the carbon dioxide purity and the seven factors of feed purity, feed temperature, column top pressure, column top temperature, column reactor heating temperature, column reactor pressure and column reactor temperature built on the actual production data by using artificial neural network

    摘要為提高提純塔出口二氧化碳純度，根據實際生產數據運用人工神經網路方法建立了出口二氧化碳純度與進塔純度、進塔溫度、塔頂壓力、塔頂溫度、塔釜加熱溫度、塔釜壓力、塔釜溫度7個因素之間的非線性模型。
  8. Effects of different fuel - air ratios and different geometric parameters of dual - stage swirler ( such as inner diameters of the primary swirl and secondary swirl passages, outer diameters of the secondary swirl passages, vane angle of the primary and secondary swirler, the distance of the flare exit from throat etc ) on combustion performances are studied experimentally. the experimental results show that radial profiles of the outlet gas temperature 、 combustion efficiency 、 emissions of co2 、 co and nox and lean blowout are affected with different degrees by the different geometric parameters of dual - stage swirler and the arrangement of primary holes

    在不同油氣比下，不同的雙級旋流器幾何參數（例如:一級與二級旋流器出口內徑d 、葉片安裝角、二級旋流器出口外徑d 、二級旋流器的喉道到出口截面的距離l和喉道前後的圓弧半徑r以及主燃孔孔布局等）對單頭部環形燃燒室的出口溫度分佈、燃燒效率、貧油熄火油氣比以及污染物（ co _ 2 、 co和nox ）排放等燃燒性能的影響規律進行了研究。
  9. Great difference in pressure for two flow made pressure wave system and it help to extend the delay time for gas in chamber, which increases combustion effusion. second, to increase combustion effusion, the inlet temperature of air and gas should be enhanced in the range of heat releasing in chemical reaction. third, the first work condition is unburned absolutely and the second work condition is burnt in shear layer of inlet and the end of down wall zone in straight segment

    對于壓力差很大的兩股氣流，所形成的壓縮波系的結構可以增加燃氣駐留時間，提高燃燒穩定性;為了提高擴散燃燒的效率，在保證能放熱的化學反應溫度范圍之內，應適當提高燃氣及空氣的來流入口溫度;燃氣噴嘴應居於燃燒室軸線上，是改進超音速燃燒室結構的一種思路。
  10. Furthermore, the impacts of the geometric dimensions of the coils, the inlet temperature and the flow velocity of the secondary fluid on the charge / discharge modes were discussed. a comparison of the total freeze - up and the partial freeze - up has also been made

    研究了載冷劑進口溫度、流速和盤管材料的熱導率對蓄冰盤管傳熱性能的影響，並對完全凍結方式和不完全凍結方式的結冰和融冰過程作了比較。
  11. Turbine intake temperature

    渦輪進口溫度
  12. Nominal cooling capacity conditions : chilled water in 12, out7, cooling water in 30, out35

    冷量是依據冰水入口溫度12 ，出口溫度7 ;冷卻水進口溫度30 ，出口溫度35計算得出。
  13. The results showed that the material surface temperature in normal atmosphere was 100 during constant drying rate anyhow superheated steam temperature

    結果表明，常壓下無論進口溫度如何，恆速乾燥階段物料表面的溫度均為100 。
  14. Air systems are effective for space heating because a heat exchanger is not required and the collector inlet temperature is low throughout the day ( approximately room temperature )

    空氣系統對于空間供熱是有效的，因為熱交換器是不必需的，且收集器的進口溫度全天低（近似室內溫度） 。
  15. The effects of the flow rate, the inlet temperature, the inlet concentration and the system pressure, the temperature of cooling wall and the radius on the features of condensation process with binary ( tfe / nmp ) vapor were gained

    同時，也得出了進口流量、進口溫度、進口濃度、體系壓力、冷卻壁溫和管徑等參數對垂直管內部分膜狀冷凝過程參數分佈的影響規律。
  16. Fresh inlet temperature range which satisfies given error limits is achieved, and the effect of instrumentation precision on accuracy of test results is analyzed by calculating and analyzing uncertainties of sensible effectiveness tests

    通過對顯熱效率測試的不確定度的計算與分析，得出了滿足給定誤差限的新風進口溫度范圍，並分析了儀表精度對測試結果準確度的影響。
  17. At the same time, experimental study on boiling heat transfer by changing mass flow of refrigerant, mass flow of water, and inlet temperature of water was also finished. and then the performance of miniature evaporator was estimated

    本文完成了液單相、兩相熱平衡實驗和阻力特性實驗，研究了製冷劑在管內流動的壓降;同時進行了微型蒸發器流動沸騰實驗，通過改變製冷劑質量流量、水的質量流量、水的進口溫度等，實現了對微型蒸發器的性能評價。
  18. The experimental results showed that : in the summer operating mode, the refrigerating capacity and coefficient of performance of the system decreased with the increase of the temperature difference between supply and return ground - water and the water supply temperature ; in the winter operating mode, the refrigerating capacity and coefficient of performance of the system increased with the decrease of the temperature difference between supply and return ground - water and the increase of the water supply temperature. it also showed that, change the are of heat exchanger has great influence of refrigeration system

    本課題通過實驗測試井水進口溫度、進出口溫差以及在不同溫差下換熱器面積匹配對系統性能的影響。實驗結果表明，夏季工況下，隨著井水進口溫度的升高，進出口溫差的增大，系統製冷量減小，機組cop降低，系統運行性能惡化。冬季工況下，隨著井水進口溫度的升高，進出口溫差的減小，系統的制熱量增加，機組cop提高，系統運行性能優化。
  19. The following is the experimental investigations on solidification process of stearic acid. the influences which the inlet temperature and reynolds number of the cooling water have on the solidification process are presented. figures that display how heat flux change versus time has been drawn and analyzed

    然後是硬脂酸凝固問題的實驗研究，分析了換熱流體進口溫度、換熱流體re數大小對凝固過程的影響，繪制了凝固過程中熱流密度變化曲線，比較了螺旋肋肋寬對強化傳熱效果的影響。
  20. Increase of inlet temperature for gas turbines is an effective measure to enhance the thermal efficiency of gas turbine, but this is limited to a great extent by the structural, strength of thermal parts in the gas turbine, whereas adoption of advanced cooling technology is one of effective measures for enhancing the inlet temperature of gas turbines

    摘要提高燃氣透平進口溫度是提高燃氣輪機熱效率的有效措施，但這在很大程度上受到燃氣透平熱部件結構強度的限制，而採用先進的冷卻技術是提高燃氣透平進口溫度的有效措施之一。
分享友人
分享到 Line

分享到臉書