進氣彎管 的英文怎麼說

中文拼音 [jìnqìwānguǎn]
進氣彎管 英文
ansaugkruemmer
  • 進 : 進構詞成分。
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  • 進氣 : air admission; admission; inlet; onflow; charging; access of air; admittance; air in; air intake;...
  1. The saw - tooth profile at the bottom of the barge board now features two ' teeth ' bending upwards to dramatically reduce turbulence, and therefore improve both cooling and airflow management close to the sidepods

    破風板底部呈現鋸齒狀，現在其中兩個牙齒向上彎曲，戲劇性地減低了亂流，也因此增進了冷卻的效率和側箱附近氣流的管理。
  2. Firstly, simulate flow field of rear smoke channel, plot velocity magnitude and ash concentration distribution in section of entry of heat pipe air preheater, compare with data which were measured in guiyang power station, verify simulation to be reasonable and right. secondly, simulate all kinds of factors which affect flow field ' s uniformity such as length, thickness, location of diffluent board, ash concentration, ash diameter, and so on, find the chiefly factors. thirdly, install guide board in curve channel in rear smoke channel, then simulate its " flow field, plot velocity magnitude and ash concentration distribution

    在此基礎上模擬在冬夏兩季不同情況下，不同流速對熱管空氣預熱器壁面溫度的影響；然後對影響整個流場分佈的各種因素：包括分流板長度、厚度、偏離中心流道位置的偏離度、飛灰濃度、飛灰粒徑等因素進行數值模擬；最後提出在分流煙道轉彎處加裝導流板，並模擬加裝導流板后的流場分佈，得到下級空氣預熱器出口、熱管空氣預熱器進口處的斷面速度場分佈、濃度場分佈，以論證加裝導流板能達到流場均勻化的作用。
  3. Concerning big leakage of the mine slurry at the seal of the phosphorite wet miller inlet and feed syphon, the mine materials in the siphon is easy to be blocked, the imported seal structure is amended to the labyrinth structure

    摘要針對磷礦濕磨機進口與進料彎頭密封處漏礦漿嚴重、彎管內礦料易堵塞的情況，將進口密封結構形式改為迷宮式密封，並在進礦彎管上增開壓縮空氣管介面。
  4. In order to improve the prediction accuracy, the sensitivities of pipe friction coefficients, pressure loss coefficients in bents, wall temperatures and heat transfer coefficients in pipes and cylinders on the volume efficiency are investigated

    為提高充氣效率的計算精度，由模擬計算和相關試驗，分析了管道的摩擦系數、彎管的壓力損失系數、進氣管壁和氣缸壁溫度及其傳熱系數對充氣效率的影響程度。
  5. The results show that the heat transfer in intake manifold and cylinder has obvious effects on the volume efficiency, while the pipe friction coefficients and bent pressure loss coefficients have less effect

    結果表明，進氣管和氣缸的傳熱對充氣效率的影響較顯著，而管道摩擦系數和彎管壓力損失系數對充氣效率的影響較小。
  6. Each of these sanitary fitments is fitted with a trap including u shaped water trap, bottled trap or anti - syphonage trap to prevent foul smell and insects in the soil pipe from entering into the premises

    上述生設備都各設有隔氣彎管包括u形樽形或反虹吸隔氣彎管，防止污水管的臭味和昆蟲進入樓宇內。
  7. Each of these sanitary fitments is fitted with a trap ( including u shaped water trap, bottled trap or anti - syphonage trap ) to prevent foul smell and insects in the soil pipe from entering into the premises

    上述?生設備都各設有隔氣彎管（包括u形、樽形或反虹吸隔氣彎管） ，防止污水管的臭味和昆蟲進入樓宇內。
  8. The design and research work on the inlet turning tube had been carried out mainly based on the experiment results and working experience. with the development of computational fluid mechanics ( cfd ), it is quilt possible to simulate the flow inside the inlet turning tube accurately and get a better understanding of the flow phenomena in the flow field to guide the design, in this paper, detained simulations of the flow fields inside two different compressor inlet turning tubes have been presented

    過去國內對它的設計和研究主要藉助于經驗和利用實驗手段來進行，本論文使用先進的三維氣動計算技術，藉助功能強大的流場計算軟體，對壓氣機進氣彎管內部流動情況進行了詳細和準確的數值模擬，為壓氣機進氣彎管的優化設計提供更為準確的理論依據及指導原則。
  9. Petroleum and natural gas industries - induction bends, fittings and flanges for pipeline transportation systems - part 3 : flanges iso 15590 - 3 : 2004 modified ; english version en 14870 - 3 : 2006

    石油和天然氣工業.管道輸送系統用進氣彎管配件和法
  10. Petroleum and natural gas industries - induction bends, fittings and flanges for pipeline transportation systems - part 2 : fittings iso 15590 - 2 : 2003 modified ; english version en 14870 - 2 : 2004

    石油和天然氣工業.管道輸送系統用進氣彎管管件和法
  11. The performance of modern internal combustion engine for locomotives often depend on the improvement of the supercharge performance. as part of the main component of the compressor, the inlet turning tube will affect the performance, especially the surge margin, of the compressor directly

    現代內燃機車柴油機的功率和性能的提高在很大程度上取決于增壓器性能的提高，壓氣機進氣彎管作為增壓器的組成部分之一，直接影響壓氣機的性能和喘振裕度。
  12. Then the pro ? models have been input into pro ? m, an automatic mesh generating software, to create the mesh system for numerical simulation. after defining some proper boundary condition, the flow analysis have been performed through the use of star ? d, a powerful cfd software. with some careful analysis of the simulation results and comparison of the two models, some guiding principles for the design optimization of the compressor inlet turning tubes have been concluded

    論文主要工作包括：通過對壓氣機進氣彎管幾何形狀的深入分析，利用三維建模軟體pro / e生成其三維幾何模型；利用網格自動生成工具pro - am ，根據pro / e生成的三維幾何模型生成了數值模擬所用的計算網格；對壓氣機進氣彎管內部流動進行了詳細的氣動計算，對原進氣彎管與新型進氣彎管的計算結果做了對比分析，對其結構的優化設計提出了指導原則。
  13. We describe a case of unexpected kinking of ett intraorally while craniotomy was underway

    在此，我們描述一例在開顱手術進行中，氣管內管在口腔內非預期彎折的病例。
分享友人
分享到 Line

分享到臉書