進水閘門 的英文怎麼說
中文拼音 [jìnshuǐzhámén]
進水閘門
英文
entrance gate-
A fracture dynamics analysis is given to an accident on a gudgeon link of the miter gate of a dam
摘要對某水壩船閘人字門拉桿斷裂事故進行斷裂動力學的定性與定量分析。Secondly, on the base of the analyzing design characteristic, this paper presents theoretical basis according to " design specification about steel gate in water conservancy and hydropower engineering " ( thereinafter for short specification ). it introduces module design means of hmvcad system. in the light of this means, it develops the module that can design the gate according to original data and specification automatically, the module of making the original design by user ' s experience, the module of majorized adjustment, the module of alarm device
其次，本文在分析了弧形閘門設計特點的基礎上，按《水利水電工程鋼閘門設計規范》 （ dl t5039 - 95 ，以下簡稱《規范》 ）給出了設計的理論依據，介紹了hmvcad系統的模塊設計方法，據此研製了能根據原始資料自動按規范設計的程序模塊，以及據用戶經驗進行初步設計、優化調整、預警裝置等功能模塊。Based upon the present regulation, the design and construction check and structure strength check, the electric power generation water inlet anchor gate crane platform ' s hydro - engineering structure of fushui power plant were conducted and an analysis for the reasons of building structure fracture was carried out
摘要進行了富水電廠發電進水口閘門啟閉機平臺安全檢測，依據現行規?對其建築物進行了設計與施工復核、結構的強度復核和建築物的裂縫成因分析。The common areas, including corridors, lifts and lift lobbies, back staircases, the gates of entrances to the building and letterboxes were disinfected yesterday. water storage tanks were also cleaned
大廈的公用地方包括走廊、電梯及電梯大堂、后樓梯、大廈入口閘門及信箱等已於昨日進行消毒，貯水箱亦已作清洗。So according to the technology regulation of reclamation engineering, hydraulic calculation must be carried out in the design of final closure. this paper firstly introduces the progression and present situation of reclamation engineering, emphasizing on the features of present reclamation and on the experiences and theories of home and abroad ; using fortran perfects the hydraulic calculation program of the closure and makes the program to meet different conditions ( such as considering flood, the variation of time interval, multi - entrance, multi - reservoir capacity ), and after comparing and analyzing a great deal of schemes, the reasonable computation scheme was brought up ; the interface of the program was carried out by the programming language vb to make the process of calculation become easier and more distinct, so the result can be analyzed and handled more directly ; vb is used in the later management of the result to plot the graphic chart of the isoline of the maximum of hydraulic element ( the velocity of flow, the drop height and the rate of flow ) automatically ; finally it was applied in the reclamation project of dongbidao of fuqing
本文首先介紹圍海工程的發展進程與國內外圍海的開發現狀，重點介紹了我國目前圍海工程的特點及在圍海工程實踐中積累的經驗和理論；利用fortran語言完善堵口工程龍口水力計算程序，使程序可以滿足圍海工程復雜工況下（如考慮內港洪水、計算時段的變化、多口門、多庫容、多水閘）的龍口水力計算，並進行大量方案的比較和分析，提出合理計算方案；利用面向對象的可視化編程語言vb進行界面開發，使計算過程有良好的人機界面，更直觀地對計算結果進行分析和處理；計算結果的后處理採用vb編程實現龍口水力要素最大值等值線圖的繪制；並運用所編軟體對福建省福清市東壁島圍墾工程進行龍口水力計算，為堵口合龍提供科學依據。Seawall and sluice are the parts constructed in advance, while final closure is the last part in construction. the hydraulic condition during the final closure process is worse than that during any other processes. and with the compressing of the entrance, the hydraulic condition becomes badly, the drop height of entrance can reach 2 to 3 meter, the maximum velocity of flow even reaches 6 to 8 meter per second and flow condition also becomes complex
海堤和水閘的修建都是圍海工程先期施工的部分，堵口則是海堤修築的最後階段，堵口合龍成敗關繫到圍海工程成敗，由於此階段所遇到的水力條件十分惡劣，口門落差可達2 3m ，流速最大可達到6 8m / s ，且水流極其復雜，根據我國《圍海工程技術規范》規定圍海堵口必須進行龍口水力計算。According to the actuality of the studied water power station, the thesis combine the advanced fieldbus technique, ethernet and the traditional hydraulic technique together, and use them to design the supervise controlling system of the water power station. base on the gate - controlling request of the water power station, designed the gate ' s hydraulic hoist system
文章從結合所研究的水電站的實際需要出發，將先進的現場總線技術、以太網技術與傳統的液壓技術相結合，並應用到水電站閘門監控系統的實際設計過程中。論文根據所研究水電站閘門控制的具體技術要求，設計了適合該水電站的液壓啟閉機系統。The researches including discharge capacity, pressare properties, cavitation characteristics at some key positions, hoisting load of the gate, configuration of energy dissipator at the exit dentated - sill, and downstream scouring were performed by hydraulic model tests
藉助系列水工模型試驗對水布埡放空洞的泄流能力、壓力特性及關鍵部位的空化特性、閘門啟閉力、出口鼻坎消能工體型及下游沖刷等進行了較深入的研究、分析。Abstract : using a series of model tests, the properties of discharge capacity in the closed conduit due to inflow in gate shaft is studied and a method for estimating reducing discharge capacity is provided to designers
文摘:通過系統模型試驗，研究了泄水道因進口閘門井進水減小泄流能力的特性，並提出了估算方法，可供設計應用。Chapter two ascertains main technological factor of dong gou lock reconstructing, including forecast the cargo and volume through the lock to reason about representative type of vessel designed for through the lock and its operation organize. chapter three design the renovate engineering through ascertaining the main technological factor scale of the lock, dimension, designed water level and altitude, including design of structure of the lock, lock chamber and lock gate, and select the main technological factor and pattern of headstock gear. chapter four draws a comprehensive compare of the two design scheme of the renovate project with engineering project economy evaluation method, and makes out the recommended scheme, and furthermore, to calculate the economic evaluation index of the recommended scheme and makes the economic sensitivity analysis of the scheme and finally demonstrate economic feasibility of the scheme
本論文共分四章：第一章主要介紹了原東溝船閘的地理位置和營運現狀，說明了船閘在航道建設和水資源綜合利用中的作用及東溝船閘改造的必要性；第二章東溝船閘改造的主要技術因素確定其中包括東溝船閘過閘貨種和貨運量發展的預測，並確定東溝船閘的設計代表船型及營運組織；第三章東溝船閘改造工程設計本章通過船閘改造工程主要技術參數：船閘規模、尺度、設計水位和高程等的確定，設計了二個船閘改造方案，包括鋼筋混凝土整體塢式閘首結構、閘室和閘門的設計，並選定了啟閉機的主要技術參數和型式；第四章採用了工程項目經濟評估方法對東溝船閘改造工程二個設計方案進行全面綜合比較后，確定了推薦方案。According to the demands of the enterprises, combining with the actuality, this dissertation has designed a hydraulic control system for inlet hatch, in order to meet the waterworks " requirements - cutting off the inlet in time when an electrical failure should occur. this system benefits the safety and well - running of waterworks. besides, with the simulink in matlab, it has simulated the dynamic characters of the system to optimize the parameters, components and system
根據企業需求，結合現狀，本文設計了速閉閘液壓控制系統以滿足水處理廠遠程控制閘門及在斷電時快速切斷進廠水源的迫切需要，有利於保證水處理廠的安全、正常運行：利用matlab提供的simulink軟體包對速閉閘控制系統的動態特性進行模擬，來達到優化參數、元件、系統的目的。The stability analysis and structural optimization design of the hydraulic automatic tilting gates with connecting lever and rolling wheel were carried out in the paper to make them not only be better applied in all kinds of water conservancy but also be wildly applied in ship project, city environmental protection, and other correlative project, further to better the social and living condition
本文對連桿滾輪式水力自動翻板閘門進行穩定性分析和結構優化設計，使得它們不僅能更好地應用於各類水利水電工程中，而且能廣泛應用於航運工程、城市環境保護和其他相關工程中，將會對社會的發展和生活環境的改善有著重要的意義。Mixture mixing : install and debug the mixing equipment before construction, take the trial mix according to the mixture ratio, and find out the turning on location of every hopper strobe as well as the relation among material flow of every kind, draw up the curve, and if there is adjustment because of factors like material batch, difference of moisture content and so on, it need to be confirmed by the laboratory so as to ensure the mixture ratio of construction meet the design requirement
混合料拌和：施工前首先安裝、調試好拌和設備，根據確定的配合比進行試拌，找出各料斗閘門開啟位置與各種材料流量的關系，並繪製成曲線，如因材料批次、含水量不同等因素而調整，須由試驗室確定，以確保施工配合比符合設計要求。And some suggestions for gate vibration study are made
並對進一步做好水工閘門的振動研究工作提出了建議。According to the research development of flow - induced gate vibration in recent years, the paper presents a retrospect and a summary on the relationship between hydrodynamic loads and gate vibration characteristics, the hydrodynamic load characteristics and controlling means, the optimum design methods for gate anti - vibration, the dynamic stability analysis of the radial gate ' s arm, the methods to simulate the gate ' s hydro - elastic vibration, as well as the simulation analysis of flow - induced gate vibration
摘要從水動力荷載與閘門振動特性的關系、水動力荷載作用特點及其控制方法、閘門減振優化設計方法、弧形閘門支臂動力穩定性分析、閘門水彈性振動模擬方法以及閘門流激振動模擬分析等方面，對水工閘門流激振動的研究進行了回顧。The thesis analyzed the development of the gate ' s hoist and its controlsystem, and the localization of the gate ' s operating machine ' s traditional hydraulic system, according to today ' s control technique, especially the characteristics of the profibus fieldbus, the thesis put forward the project that " the gate supervise controlling system base on the profibus control and ethernet technique ", according to that project, completed plc control procedure and the procedure of the supervise and control ( supervise and control software and man - machine interface ), at last the thesis set up a ethernet network for the monitor and the plc correspondence of a place of honor machine and plc and a fieldbus network for the far i / o mold and the plc, made the gate supervise and control by network
文章對閘門啟閉機及其控制系統的發展狀況和傳統液壓啟閉機控制系統的局限性進行了詳細分析，並結合當前控制技術，特別是profibus現場總線控制技術的特點，針對所研究的水電站的實際情況提出了「基於profibus現場總線控制和以太網技術的閘門監控系統」的技術方案。並根據該方案完成了下位機（ plc控製程序）的編制和上位機（監控軟體和人機界面的組態）的組態。最後通過組建上位機與plc的通信以太網路和遠程i o模塊與plc之間的總線網路，實現了整個閘門監控系統的網路化。Abstract : the outflow through gate controlled multi - opening spillway of yinhe reservoir was analyzed. the analysis results were checked by the site observed data
文摘:分析了音河水庫多孔有閘門控制的溢洪道出流，並用出流的實測資料進行了檢驗。The system is designed to collect the height of water of the measured points, control the slacker of the river and process the data in the distance
該系統主要用於實現對河流沿岸各測點處的水位數據採集、閘門狀態的遠程測量和對各測點處的水閘進行遠程控制。The network can control the opening, shutting and surveillance the circulate of the eight gates, which stand in different positions, and make the system satisfied the various requests of that water power station ' s production, and still guaranteed the system had very advanced at the same time
通過該監控網路，可實現對該水電站分居於八個不同壩段的閘門的運行及運行狀態的控制與監視，從而使得該監控系統在滿足水電站實際生產的各項要求，同時還保證了該系統具有相當的先進性。Being been produced upon advanced design and technology at home and abroad and fitted with advanced manual and electric actuators and accordance with the standard of 《 cj / t3006 - 1992 cast iron gate valve for water - supply and sewerage 》, our valves are strong in sealing capability, good in antifriction, easy to mount, flexible for opening and closing and long in service life
本公司的閘門系列產品符合cj / t3006 - 1992 《供水排水用鑄鐵閘門》標準，該產品綜合國內外先進的結構和工藝，並採用國內先進的手、電動控制裝置，使得閘門具有密封性強、耐磨性好、安裝方便、啟閉靈活、壽命長等特點。分享友人