進給速度 的英文怎麼說

中文拼音 [jìngěisùdù]
進給速度 英文
feed rate
  • 進 : 進構詞成分。
  • 給 : 給Ⅰ動詞1 （送對方某物; 使對方得到） give; grant 2 （用在動詞后 表示交與 付出） pass; pay 3 （叫; ...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 速度 : 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. （快慢的程度） speed; rate; pace; tempo
  1. The effect of axial feed velocity on hydroforming tri - branch tube by fem

    軸向進給速度對內高壓成形三通管影響的有限元分析
  2. Influences of feed rate on machining precision during grinding metal ceramics blade by diamond grinding wheel

    進給速度對磨削金屬陶瓷刀片精度的影響
  3. In the thesis, the general situation of the domestic and abroad developments in the field of the numerical control interpolation algorithm for aspheric surface machining is reviewed firstly, for the poorness of recent numerical control interpolation algorithm, an numerical control interpolation algorithm that based on the genetic algorithm ( ga ) and neural network ( nn ) is introduced

    在數控系統中，它是生成加工軌跡的一個最基本的子程序，在很大程度上決定了數控機床的加工精度和最大進給速度。本文首先綜述了國內外非球曲面超精密加工中所運用的插補演算法的發展概況。
  4. Design of shear feed rate fuzzy controller in machine tool

    機床切向進給速度模糊控制器的設計
  5. Regulation method for feed speed of fully hydraulic drilling machine

    全液壓鉆機進給速度調節方式探討
  6. Rapid traverse rate of feed

    快速橫向進給速度
  7. Main cutting speed

    進給速度
  8. With plc controlling feed speed automatically, this machine, occupying little space and enjoying configuration, is easily operated

    本機床結構緊湊，佔地面積小， plc自動控制進給速度，操作簡便。
  9. A new method, which named reverse shrinking surplus method, has been pointed out based on the fem in order to optimize the speed curve of the spindle

    摘要在基於有限元數值模擬的基礎上提出了反向最小余量法，用以優化芯輥進給速度曲線。
  10. The optimized speed curve can bring a steady press - down dimension in the process of the ring rolling which could assure high quality products

    優化后的芯輥進給速度曲線能保證輾擴過程中始終有理想的每轉壓下量，從而降低缺陷的發生，提高零件質量。
  11. The feedrate in tangential direction was adjusted by the fuzzy velocity controller for reducing the worst burrs and defects to obtain better quality contour

    而模糊速度控制器被用來調節工具進給速度，從而徹底清除較大的毛刺，避免損害工件和刀具，得到理想的加工表面。
  12. A control method is presented where least square arc approximation and timed interpolation are employed. using it, the number of segments of fitted curves is made minimum while the accuracy is guaranteed, so that data transmission between cad and cnc systems is decreased and setted feeding rate can be realized. this method has already success fully been used for flame cutting and controlling saddle - backed curve for pipe connection when feeding rate is required to be higher

    提出了一種採用最小二乘法圓弧逼近及定時插補控制方法，在保證精度的前提下，可使擬合圓弧段數最少，從而減少cad系統與cnc系統的數據傳送，可實現給定進給速度.該方法已成功地應用於要求較高進給速度的接管馬鞍型曲線火焰切割擬合控制
  13. The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement

    研究結果表明，增大砂輪軸向進給速度和減小工件轉速，採用粗粒度砂輪有利於提高磨削矽片的材料去除率，砂輪軸向進給速度對材料去除率的影響最為顯著；適當增大砂輪轉速，減小砂輪軸向進給速度，採用細粒度砂輪可以減小磨削表面粗糙度；在其它條件一定的情況下，砂輪速度超過一定值會導致材料去除率減小，主軸電機電流急劇增大，表面粗糙度變差；採用比# 2000粒度更細的砂輪磨削時，材料去除率減小，矽片表面粗糙度沒有明顯改善。
  14. By using a wafer - rotating grinding machine, the influence of the main process factors including grit size of diamond grinding wheel, rotating speed of the wafer chuck table, rotating speed and the down feed rate of the cup grinding wheel on the material removal rate, spindle motor current and wafer surface roughness in grinding large size wafer are experimentally investigated

    摘要利用基於自旋轉磨削原理的矽片超精密磨床，通過試驗研究了砂輪粒度、砂輪轉速、工件轉速及砂輪進給速度等主要因素對材料去除率、砂輪主軸電機電流以及磨削后矽片表面粗糙度的影響關系。
  15. Renewal made of the mould, advanced high - speed machining center, with the high rotational speed, so high as to enter for the speed, high precision and high efficiency to replace profile modelling to mill, namely process and replace simulation to process with the data, from the three - dimensional data mould three - dimensional structure numerical control cnc form of the products, all appear with the data

    模具製造的更新，先進的高速加工中心，以高的轉速高的進給速度高的精度和高的效率取代了仿形銑，即以數據加工取代模擬加工，從產品的三維數據模具三維結構數控cnc程式，全部以數據顯現。
  16. These machines and tools have a rich adjustment merit ability, and his two - way riveting bit, riveting pressure and advance to speed can be transferred to riveting capacity, and system pressure also can be transferred, and fully pledges optimum riveting effect

    該機具有豐富的調整功能，其雙向鉚接位鉚接壓力進給速度鉚接量都可調校，系統壓力也可調，充分保證最佳的鉚接效果。
  17. The spkm ( serial - parallel machine tool ) is a new type of machine tool developed in the recent years. it is consisted of serial and parallel mechanism which increases spkm " s displacement and rotary angle, as well as stiffness, accuracy and feed speed

    混聯機床不僅繼承了並聯機床高剛度、高精度和高進給速度等優點，還具備了串聯機床大移動行程和大旋轉運動角的特點。
  18. To raise machining efficiency and make nc machine working in a perfect state, manipulator would constantly adjust feed rate and main spindle speed trim knobs in the operate panel

    為了提高加工效率，操作者在加工過程中根據加工狀況不斷地調整操作面板上的進給速度、主軸轉速這兩個參數的修調旋鈕，使機床工作在較理想的狀態。
  19. By using the general jigs for the general tools, it is difficult to get terrifically slow feeding speed, stable machining quality and smart micro profile. the overall frame of the control system on micro fabrication process of excimer laser was analyzed and instituted based on its unique characteristics

    在微細加工中如果採用傳統的數控加工機床，由於其體積龐大，夾持工具粗重，難以獲得極低的加工進給速度、穩定的加工質量和靈活多變的微小加工輪廓。
  20. For instance : nowadays use the small and exquisite paint - spray robot abroad, can scan the size of specification of the work piece and programme by oneself automatically, whole craft circulation go on in succession, according to accurate to is it stock give speed to control procedure have, all parameters of spraying paint in the angle and distance etc., use the painting amount to obviously reduce

    如：當今在國外使用小巧的噴漆機器人，能自動掃描工件的規格尺寸並自編程序，整個工藝循環連續進行，按程序精確控制進給速度噴漆角度和距離等所有參數，用漆量明顯減少。
分享友人
分享到 Line

分享到臉書