運動后圖形 的英文怎麼說
中文拼音 [yùndònghòutúxíng]
運動后圖形
英文
postexercise tracing-
Dish in breakthrough evidence just appeared on attempt of pattern day wire dish in move general relatively dovish, dish in a flaw is banker hits share price again rarely all price lower part moves, not was necessary to make this motion that day, if discover dish in hit downward low all valence is answered smoke faint when, should take care whether open quotation configuration is one leads much movement, the essentials that spots this movement is after luring polymorphous condition open quotation one hour, drop downward necessarily broken all price goes low, indication banker is protected involuntarily dish, make quake of purpose
盤中形態日線圖上剛出現突破跡象的個股盤中運行一般都較為穩健，盤中一個破綻就是莊家很少將股價再打到均價下方運行，當天沒有必要做這個動作，假如發現盤中向下打低均價回抽無力時，要小心是否開盤形態是一個誘多動作，識別這個動作的要領是誘多形態開盤一小時后必然向下跌破均價走低，顯示莊家無心護盤，有意作震蕩。Firstly, given the seed point of the interesting region, it detects the edge points that has the shortest distance to seed point in some directions, takes these points as the control points to form the initial b - spline active contour
該方法是一種圖像兩步分割方法，給出位於感興趣區域內的種子點后，首先用canny運算元檢測出各個方向上與種子點最近的棱邊點，以這些點為控制點，形成初始的b樣條活動圍道。At the same time, based on weld pool image characters, a method for image processing is presented, in which gray - scale morphological operators is used to process weld pool images. by this method, the important geometrical parameters of weld pool are measured
同時結合實際的焊接自動化中熔池圖像的特點，詳細介紹如何利用灰度形態學，設計基於com的形態處理運算元，並且實時提取熔池的最大寬度、半長、後部面積、后拖腳等重要的幾何參數。The measurement system can automatically control the movement of servo motor and communicate with vna through gpib bus to setup the measurement variable automatically, measure the phase of s parameter. it also can progress the measurement data on the background, display the results by graph data, store them in the data files
系統自動控制伺服電機的運行，對測試探頭完成指定的移動定位;通過gpib總線與矢量網路分析儀器通信，自動完成相關測量參數的設置以及s參數的相位測量;對測得的數據進行后臺處理，將結果以圖形、數據文件的方式顯示、保存。In this paper, with the help of the idea of software engineering, the object - oriented developing technique, structured software development method, the inter - process communications in windows and the fortran / c + + mixed programming technique, the windows version of the pre - processor and the post - processor module are developed : the pre - process module is parted as four function modules. the part of graphic display codes of the pre - processor and the post - processor module are translated and modified as background processes. the interactive graphic interface in windows style is designed as foreground processes
基於軟體工程思想，本文綜合運用面向對象技術、結構化程序設計方法、 windows進程間通信技術、 fortran c + +混合聯編技術，對sheet - forming的微機版本中的前、后處理器模塊進行了研製：將前處理器模塊進一步劃分為四個功能模塊；優化編譯前、后處理器的圖形顯示部分代碼並將其作為后臺程序；設計windows風格的前臺互動式圖形界面；利用本文設計的中介程序實現后處理前臺界面和后臺程序之間的通信。( 3 ) in this study, after building correct model and executing rational calculation, the results, which included stress - strain curve, bent chart, displacement vector chart, cracks location, loaded - displacement curve and animations about the movement of components
（ 3 ）本文通過合理的建模和有效的計算，得出結構在爆破后構件的應力應變情況、路徑圖、位移變形值、裂縫示意圖及構件運動動畫等結果。This thesis is a fem analysis of opening process of the folded horizontal tail wing of some aircraft, and the work includes modeling the detailed mechanic assembly of the tail wing, and computing its elastic dynamic process by large - scale fem software system, ansys and ls - dyna3d, as well with the postprocessor tool - lspost to take the computational results into visualization
本文運用大型有限元cae軟體ansys和ls - dyna3d對某具體飛行器水平折疊尾翼的機構運動進行了細致的有限元建模和動力學計算分析，運用lspost對計算結果進行了詳細的后處理，運用可視化技術對數值分析結果進行了圖形及曲線描述。On the bases of these, we give computer graphics models of some basic physical variables, such as time, mass, force, velocity and acceleration, etc. thus we can build an integrate system. then we can do some research work about the models " behavior properties, such as collision, collision response and invert kinematics, and so on
在此基礎上，對經典力學中的基本物理量如時間、質量、受力、速度、加速度等進行計算機圖形學建模，以期建立一個完整的理論體系，然後在這個體系基礎之上研究模型的行為屬性，如干涉、碰撞以及碰撞后的響應、 .關聯物體的運動等。Much research work has been done on improving post - treatment of 3 - d fem numerical simulation. and a software package running in windows98 system has been compiled which is used for analysis of geostress field in oil field. it can calculate the transform of vector in 3 - d space
5改進了三維有限元模擬后處理分析，編制了在windows系統下運行的油田應力場地質分析程序，形成了軟體包，實現了矢量的三維空間變換及結果的可視化及自動成圖，提高了分析的自動化水平。Based on the above study, this topic has realized simulator run environment. after the start - up of simulation running environment with loaded object code, each simulation component shall harmonious run under the logic control of application software, so as to support the software commission and test verification
支持從構件庫中選取需要的模擬構件，以可視化圖形編輯的方式構造模擬目標硬體環境;加載目標碼的模擬運行環境啟動后，各模擬構件能在應用軟體邏輯的控制下協調運行，從而支持嵌入式系統軟體的調試和測試驗證。分享友人