過度淬火 的英文怎麼說
中文拼音 [guòdùcuìhuǒ]
過度淬火
英文
overquenching-
In this paper, 6013al / sicp / gr metal matrix composite ( mmc ) was produced by spray codeposition, by means of changing the medium of quenching, influence of five types of heat treatment system ( furnace cooling, air cooling, water quenching, dry ice quenching, liquid nitrogen quenching ) and different aging temperature on the damping was studied systematically
本文採用噴射共沉積方法制備了6013al sicp gr金屬基復合材料（ mmc ） ，通過改變淬火介質，較為系統地研究了五種熱處理制度（爐冷、空冷、水冷、乾冰冷及液氮冷）以及不同時效溫度（ 120 、 150 、 170 、 190及210 ）對6013al sicp grmmc阻尼性能影響。Based on the analyses on mechanical properties, microstructure and fracture of - the microalloyed steels socrv with various heat treatment technique, it can be affirmed that various fractures arttribute to various mechanism, we can draw conclusion that the strength and toughness of microalloyed steels 50crv will be increase simultaneously by optimal heat treatment technique. to illustrate the mechanism of the strength and toughness of microalloyed steels socrv, we designed the comparative experiment and observed the microstructure of the sample which occurred at different quench and tempering temperature and different tempering time. the last experiment results were determined by the four factors : fined microalloyed elements grains, the decompound of martensite, martensite transformation of remnant austenite and the second phase precipitation
為解釋微合金化50crv鋼強韌化機理，本文通過對不同淬火溫度，回火溫度，回火時間下的力學性能指標的對比及顯微分析，認為微合金元素的細化晶粒，馬氏體的回火分解，殘余奧氏體的轉變，第二相的沉澱析出共同決定了微合金鋼的強韌化情況，特別是由於微合金元素的存在，其細化晶粒及其碳氮化物的沉澱析出，導致鋼的良好的強韌性，並且如果工藝滿足第二相的沉澱析出強化大於回火馬氏體分解引起的軟化效應，會在硬度曲線中產生明顯的二次硬化現象。Induction heated oil tempered spring wire is a kind of new technical material which has been developed since 1980s. it can be heated by means of eddy induced into itself through electromagnetic coil and this method is mainly used in surface quenching. with correct designing and reasonable current frequency, induction coil and heat treatment process selected, as well as plc controlling applied, the wire can be uniform heated along cross - sectional and longitudinal direction and can be quenched and tempered continuously
應加熱油淬火-回火彈簧鋼絲，是二十世紀八十年代發展起來的新技術材料，在國外稱為itw induction heat oil tempered spring wire 。是通過線圈電磁感應鋼絲本身產生的渦流進行加熱，通常主要用於表面淬火。經正確設計，選擇電流頻率，合理的感應線圈及熱處理工藝，並實施plc控制，可使鋼絲整個截面及長度上得到均勻加熱，進行連續整體淬火和回火。Mathematical model for temperature distribution calculation during wheel quench heating process is established and used in the simulation of a certain type wheel
摘要根據馬鋼車輪淬火加熱爐的實際狀況，建立了車輪淬火加熱過程溫度場計算模型。Smooth tempered glass is manufactured by heating up float glass to swiftly and uniformly, with this special heat treatment and quenching process which increases glass strength up to four to five times vs, annealed glass, in case stresses beyond its capacity, smooth tempered glass simply disintegrates into innumerable small pieces, significantly reducing the risk of serious injury
鋼化玻璃是將浮法玻璃經過物理性淬火處理，使其表面形成均勻的壓應力，而內部則形成張應力，從而有效的提高了玻璃的抗彎和抗沖擊性能，強度達到了普通玻璃的3 - 4倍，當其破碎時則分裂成均勻純角不易傷人的小顆粒，使其成為一種現代生活中理想的安全玻璃。Abstract : the structure and the properties of the grinding ball made of the composite cast iron have been researched in this paper. the result indicates that added trace boron and a proper quantity copper to this kind of composite cast iron can increase its quench - hardening ability, and raise its hardness and impact toughness
文摘:研究了一種復合鑄鐵磨球的組織和性能，結果表明，化學成分和淬火工藝對這種復合鑄鐵磨球的組織和性能有很大影響，微量的硼和適量的銅可以明顯地提高磨球的淬透性，經過余熱淬火得到貝氏體或馬氏體基體組織，從而提高磨球的硬度和沖擊韌性。Moreover, a method for iterating thermal and magnetic analysis is put forward. in chapter 5, the distributed characteristics of eddy and temperature fields in induction heating process are simulation by fem respectively, including the distributions of eddy and temperature fields during the whole induction heating process, the influence of frequency and magnetic disperse, and the prediction of hardened depth
第五章:用ansys軟體對感應加熱過程中工件內渦流場、溫度場的一些基本問題進行模擬及分析，主要包括:加熱過程中工件渦流功率密度及溫度分佈規律;頻率與磁力線逸散對加熱效果的影響;同時對感應淬火淬硬層深度進行了模擬預測。Abstract : a new simulating method is established for the calcul ation of the hardness profile of high - carbon - concentration deep - carburization, on the basis of analyzing this process and taking into account the influence o f carbide solution and dissolution, carbon - concentration and temperature on the diffusion behavior, and the influence of the environment factor on carbon trans fer through the gas - solid interface
文摘:在對高濃度深層滲碳的特點進行分析的基礎上，考慮到碳化物的析出與溶解、溫度及碳濃度對擴散行為的影響，氣氛環境對相界面碳傳遞過程的影響，淬火烈度對滲碳層冷卻效果的影響，提出了一種新的模擬高濃度深層滲碳滲層硬度分佈的方法。Analysis which was based on the fracture mode of mould in wire - cutting processing, and the results show that the partial - quenched of mould, the non - uniformity of blank temperature and the carbide segregation inside the material are the main reasons of deformation and cracking
摘要通過分析在線切割加工中模具的破壞形式表明：模具不完全淬火、坯料溫度的不均勻分佈、材料內部的碳化物偏析是模具變形與開裂的主要原因。Analysis is done to the situation and gap of the carding clothing both at home and abroad in regarding their design, material selection, manu precison and quenching durobility for the requirement of modern machines. references is given to chinas manafacture of the same
根據當代清梳聯高產梳棉機對關鍵梳理元件的要求，從配用的錫林、道夫針布齒條的設計、原材料選用、製造精度、淬火硬度入手分析了國內外的現狀及差距，並通過對國外知名針布公司的相關介紹，為我國針布齒條製造技術進步提供了可靠的依據。Abstract : analysis is done to the situation and gap of the carding clothing both at home and abroad in regarding their design, material selection, manu precison and quenching durobility for the requirement of modern machines. references is given to china ' s manafacture of the same
文摘:根據當代清梳聯高產梳棉機對關鍵梳理元件的要求，從配用的錫林、道夫針布齒條的設計、原材料選用、製造精度、淬火硬度入手分析了國內外的現狀及差距，並通過對國外知名針布公司的相關介紹，為我國針布齒條製造技術進步提供了可靠的依據。In chapter four, in our experiments, we selected four representative mould steels as samples. after laser heat treatment, the hardness of samples was measured by special instrument, microstructure was also photographed to be analyzed carefully. through these experiments, we also debated on the theories which explain the new phenomenon occurring in laser overlapping treatment
第二章：介紹了工業中的各種激光加工技術和激光加工系統，詳細說明了本實驗所使用的高功率激光加工系統；第三章：詳細敘述了激光淬火的機理和熱傳導數學模型；第四章：通過實驗，分析激光淬火后的模具鋼的硬化帶的硬度分佈及金相組織特性，同時對激光交疊熱處理的特點及形成機理都作了深入的探討。We studied the effect of laser quenching ( harden by phase transformation ) on some representative mould steels. through measuring the rigidity on the surface of samples treated by laser heat treatment, and through photographing microstructures of the steel surface, we find many reasons attribute to high hardness. these reasons include ultra - fine grains, high density dislocation and more content of carbon in martensite
我們研究的是激光淬火對幾種典型模具鋼的作用，通過對熱處理后的試樣的硬度分佈的測定，用金相和電鏡觀察金相組織的變化，認為激光熱處理產生高硬度的原因是晶粒細化、高的位錯密度和高的馬氏體含量。Second, on the numerical arithmetic of the quench - induced residual stresses ground, the quenching process of 7075t73 aluminum plate is simulated, the effect of material characteristics along with the plate temperature varying in quenching is considered, and on conditions of the different water temperature and different plate thickness, the quenching processes are compared
2 、建立了航空鋁合金板材淬火過程的彈塑性力學模型，對航空鋁合金板材溫度場與應力場進行了數值模擬，模擬過程考慮了材料特性隨溫度變化的影響，並對不同的淬火影響因素進行了分析。Fourth, according to the actual aircraft frame part, the scale component is machined, and the quenching process of the scale component is simulated, which obtain temperature field and residual stress field in the frame scale component
4 、建立了某軍用飛機隔框零件比例件三維淬火過程有限元模型，模擬得到其三維瞬態溫度場與應力場。The effect of plastic deformation and elastic strain energy induced by pre - strain on the nucleation of martensitic transformation of low alloy ultra - strength steel sosimncrmov had been studied by pre - strain quenching in austenite state. the control over deformation magnitude and deformation temperate as well as loading pattern was performed to adjust the storage of elastic strain energy in steel before martensitic transformation, using the type of geeble - 1500 thermal analogue test machine
使用gleeble - 1500型熱模擬機，對低合金超高強度鋼30simncrmov實施奧氏體預應變淬火處理，通過控制形變量、形變溫度和加載方式，調整鋼中馬氏體相變前的彈性應變能儲備，研究了預應變所造成的塑性變形與彈性應變能對馬氏體相變的影響。These precipitation - hardened aluminum alloys gain their high strengths through heat treatment involving a severe quenching operation, which introduces a very high level of residual stresses
這些鋁合金為獲得高強度，必須進行固溶與時效處理，其中在淬火過程中會產生很大的殘余應力。分享友人