過熱分散 的英文怎麼說

中文拼音 [guòrèfēnsǎn]
過熱分散 英文
demolization
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 散 : 散動詞1. （由聚集而分離） break up; disperse 2. （散布） distribute; disseminate; give out 3. （排除） dispel; let out
  1. Through preparative experiments and optimized experiments on cu ~ zn ultrafine powders that are prepared by the method of thermal spray and ball milling, the author finds that dispersants concentration, dispersing time, ph, temperature and adscititious ions have significant influences on dispersing effects

    西安理工大學碩士學位論文通過對熱噴塗球磨法制備的超細銅鋅粉的分散性進行預試驗和優化試驗，發現分散劑濃度、分散時間、 ph值、溫度和外加離子濃度對分散作用效果有重要影響。
  2. That is the premise of the bg / ha electrophoresis codeposition. the laws of the electrophoresis deposition of the bg and ha partic les were found by the study on each of their deposition under the different conditions. the electrophoresis codeposition of the bg and ha particles had been studied and the bg / ha graded coating, which is compact in the bottom layer and porous near the surface layer, had been prepared on the surface of the dental implant after the low temperature heat treatment ( about 740 ) and fast firing ( 50 - 80 / min, heat preservation time was 5 - 8min. )

    以bg微粉和ha微粉作為塗層原料，通過研究bg和ha微粉在非水介質中的分散情況和帶電特性，選擇冰醋酸為介質，使分散在其中的bg顆粒和ha顆粒表面均帶上正電荷，為電泳共沉積提供前提條件；通過對不同條件下bg 、 ha各自電泳沉積的研究，探索出了兩者電泳沉積的規律；通過對bg和ha在冰醋酸中電泳共沉積以及后續低溫（ 740左右）快燒（ 50 ? 80 min ，保溫5 ? 8min ）熱處理的研究，在鈦合金牙根種植體基體上成功制備出了底層緻密而表層多孔的bg ha梯度塗層。
  3. Firstly, the surface characteristic of polystyrene particle is changed from water detesting to water intimity by using special techniques and admixtures so mat the compound quality with inorganic materials is insured. secondly, the contradiction between the weight and strength is solved through optimizing the particle size and using composite fiber and the best heat conductivity is achieved under the condition that the necessary strength is met. in the research process, the author solved the problem of fiber dispersing in insulating materials so that the contraction of the material is controlled

    課題研究中，首先採用特殊的改性工藝及外加劑實現對聚苯乙烯顆粒表面的成功改性，使其表面由憎水轉化為完全親水，確保與無機材料的復合質量；其次，通過採用優化骨料級配及使用復合纖維等措施解決了保溫材料的輕質與強度的矛盾，使保溫材料在滿足必要的強度的前提下，導熱系數降至最小；並且，課題研究中成功解決了纖維在保溫材料中均勻分散的問題，達到了抑制保溫材料收縮的目的；最後，通過採用復合外加劑、合適的膠凝材料及合理的配比等措施確保該保溫材料具有良好的和易性，滿足施工的要求。
  4. Scattered effect having inspected the active agent of first cousin ' s face at hydrothermal course to the anything small and roundish has been defined that the active agent of optimum surface is : dosage joined is the citric acid : 0. 05 - 0. 1g / 50ml

    實驗考察了三種表面活性劑在水熱過程中對顆粒的分散效果。考察了在水熱過程中表面活性劑對顆粒的分散效果，確定了最佳表面活性劑為：檸檬酸，加入的劑量為： 0 . 05 ? 0 . 1g 50ml 。
  5. In addition, that building experiment setting is used for experiment and analyzed performance of the heat pipe radiator that using five different working substance

    並為該熱管散熱器建立了試驗臺，通過使用五種不同的工質對該種熱管散熱器的性能加以試驗及分析。
  6. It will provide us to further study the function of xanthophyll cycle in photoprotection. the major results are as following : two cdna sequences encoding violaxanthin de - epoxidase were cloned from japonica rice ( jrvde ) and indica rice ( irvde ) with the full - length of 1887bp and 1647bp, respectively. the homology of the open reading frame is 98 % identity between two rvde genes, and more than 60 % identities with those of other species

    本論文從水稻和菠菜中克隆了編碼vde酶的基因，並通過轉基因植物進一步研究了葉黃素循環在熱耗散方面的作用，主要獲得了以下結果：首次從兩個水稻亞種（秈稻和粳稻）中克隆了rvde基因（分別命名為irvde和jrvde ）的全長cdna序列，分別長1647bp和1887bp ，兩者開放閱讀框的同源性為98 ，與其它已知vde基因的同源性在60以上。
  7. In this investigation carbon black - filled electrical conductive composites of poly ( ethylene terephthalate ) / polyethylene were first prepared through the single - screw melt - blended extrusion, then drawing, followed by the quenching and subsequent press molding. the relationships among the influencing factors including composition, hot stretching ratio and compatibilizer, morphology and properties of composites were systematically investigated. positive temperature coefficients effect and crystallization behaviors of composites were preliminarily analyzed

    本文擬採用單螺桿熔融共混擠出?熱拉伸?淬冷的新的成型方法制備炭黑填充的pet pe復合導電材料，熱拉伸的目的是使材料的分散相（ pet相）在加工過程中原位形成纖維，而炭黑基本分散在纖維中或纖維的表面上，使炭黑粒子間間距減小，形成更多的導電通路，從而提高材料的導電性能，同時保持或提高材料的力學性能。
  8. The diffusion carrier concentration profile and junction depth were measured and compared with conventional furnace processing diffusion ( cfd ). it presented following conclusions : 1 ) the temperature distribution in quartz chamber of rtd furnace is uniform because square resistance is uniform after rtd ; 2 ) the diffusion velocity of rtd furnace by a factor of three compare to conventional furnace processing diffusion ( rtd ) ; 3 ) if diffusion temperature and doping phosphorus are equivalent, doping phosphorus of rtd are more than of cfd in equivalent distance to the silicon surface

    實驗研究了快速熱擴散（ rtd ） ：通過旋塗磷膠和印刷磷漿兩種方式考查了2 4和103 103單晶硅的快速熱擴散特性，發現： 1 ）此樣機的溫度場在空間分佈上是均勻的； 2 ）快速熱擴散可以比傳統擴散快3倍的速度進行擴散； 3 ）在擴散溫度和摻雜磷源相同的條件下，與傳統擴散相比，快速熱擴散將雜質向結更深的地方推進。
  9. Nano - alkali metal hydrides and lanthanide hydrides can be prepared easily by the direct hydrogenation catalyzed by ticl4 in tetrahydrofunan ( thf ) under normal pressure. lanthanide powder of nanometric size in a finely dispersed active form was generated by the thermal decomposition of organolanthanide in vacuum. 1

    本文應用絡合催化法，在常溫常壓下，在萘/ ticl4催化體系作用下合成納米尺寸堿金屬氫化物（以nah為代表） 、納米尺寸鑭系金屬氫化物（以smh3為代表）和鑭系金屬有機化合物（以蒽鑭為代表） ，並通過真空熱解鑭系金屬有機化合物得到高分散度的納米尺寸鑭系金屬粉末（以la為代表） ，主要考察如下三個方面的內容。
  10. With the method of adding nano - particles during extracting stage, dry uhmwpe gel fiber dispersed with nano - particles is prepared, after multi - step hot drawing, modified uhmwpe fibers are prepared

    採用萃取加入的方式製成了納米粒子均勻分散的uhm認甲e干凍膠纖維，然後經過多級熱拉伸，製成納米粒子改性uhm從甲e纖維。
  11. Combined with the practical situiation in distribution network, it ' s suitable to select graph algorithm as the theoretical algorithm base. based on structure variable dissipated network theory, this thesis detailedly discusses the transforms of base - to - shape, shape - to - base, vertex - to - arc, arc - to - vertex, over - heated arc dectection, load allotting, load balancing and optimum restoration

    本論文基於變結構耗散網路理論，詳細討論了基形變換、形基變換、點弧變換、弧點變換、過熱弧搜尋、負荷分配、負荷均衡化以及優化恢復非故障停電區域供電等一系列與饋線自動化功能相關的處理演算法。
  12. The question for study is a part of subsystem of production process control system of application & demonstration project of cims of fuzhou man - made board plant under the " 863 program ". the whole system is a multi - grades distributive process control system in which the advanced process control ( apc ) technologies are applied to control the two key sectors, namely the drying sector and the heat milling sector, of the production processes of the man - made board plant

    2 、本課題為國家863計劃福州人造板廠cims應用示範工程中生產過程式控制制分系統的一部分，整個系統為多級分散式過程式控制制系統，在此將先進控制技術應用於人造板生產過程中乾燥系統和熱磨系統這兩個關鍵工段的控制。
  13. Through analyzing the effect of temperature and nitrogen on crude oil viscosity the influences of different nitrogen injection volume and injection modes on steam displacement are contrasted, the mechanism of nitrogen - assisted steam stimulation is clarified, which includes : heat carrying capacity is raised, the saturation of remaining oil is reduced after nitrogen - assisted injection is made ; crude oil flow is enhanced because of nitrogen compression and dispersion and the change of oil flow shape ; water back - production rate is improved by expanding the steam sweep volume and compensating in - situ energy ; steam distillation effect is enhanced

    通過分析溫度、氮氣對原油粘度的影響，對比不同注氮量、不同注入方式等對蒸汽驅油效果的影響，弄清了氮氣輔助蒸汽增產的機理主要表現在：氮氣輔助后增加攜熱能力，降低殘余油飽和度，氮氣的壓縮膨脹作用分散和改變了原油流動形態，增強了原油流動性；擴大蒸汽的波及體積，補充地層能量，提高回採水率，強化蒸汽蒸餾效應。
  14. It is found that aggregating state of reflective materials shows decisive influence on the capability of reflecting solar heat of coatings in dry coatings through theoretical analysis and experiments

    本文通過理論分析和試驗證明，認為在乾燥塗層中，反射材料的分散聚集狀態對塗層的太陽熱反射能力有重要影響。
  15. As the content of vermiculite minerals increased, the content of the " intercalated " shape, in which crystal gallery breadth was about of 40nm, also increased. in the curing reaction processing of polybenzoxazine / vermiculite hybrid nanocomposites intercalated with bisphenol a type precursor. according to the content of vermiculite minerals, while different shape of crystal was forming, these crystals were retarding the heat ring - opening polymerization of bisphenol a type precursors in the nanocomposites

    通過對雙酚a型ben蛭石納米插層物固化過程的分析：不同蛭石含量的插層物，在形成不同納米分散狀態固化結構的過程中，蛭石晶片對雙酚a型ben的熱開環聚合有明顯不同的阻礙作用，蛭石含量為3的插層物160的凝膠化時間較純樹脂的延長約7min ，活化能高約8kj mol ，固化反應熱晗低約14j g ，使得固化物的固化程度較純樹脂低約10 ，阻礙作用最大，其它含量的次之。
  16. ( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )

    研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。
  17. The effects of interfacial resistance, superheating, free convection due to both temperature and concentration gradients, mass diffusion and thermal diffusion, and variable properties in both the liquid and gas - vapor regions were considered

    分析中，考慮了相間阻力、液膜波動、蒸汽過熱度、因溫度和濃度梯度引起的自然對流、質擴散和熱擴散以及物性的變化。
  18. In this paper we establish math modal of transient temperature and stress fields of the turbine " rotor with finite element method, develop rotor ' s thermal status online monitor system by distribute computer and visual software, realize online show and analyst of temperature and stress fields when all kinds of transient condition, and finally provide reasonable and optimized operation suggestions, improve safety and economic level of unit sets " operation

    本文採用有限元建立汽輪機轉子的暫態溫度場、應力場的數學模型，藉助計算機分散式計算、可視化等技術開發轉子的熱狀態在線監測系統，實現汽輪機在各種過渡工況下轉子溫度場、應力場的在線顯示與分析，提供合理的操作建議，提高機組運行的安全性與經濟性。
  19. The ratio of isopropyl alcohol and pure water and temperature in the process of freezing are considerated in the research of the preparation of the pt / c electrocatalysts with freeze - drying method. the result shows, when we use 300ml pure water to wash the carbon ( 40mg ) in isopropyl alcohol ( 20ml ) to alter the ratio of isopropyl alcohol and pure water, we get the electrocatalysts with high catalytic activity ; the use of the liquid nitrogen ( - 196 ) to freeze the suspension ( carbon and precursor solution ) can make the pt / c electrocatalysts in high dispersion

    採用300ml純水對20ml異丙醇中的40mg碳載體進行洗滌抽濾，來改變預凍液中的醇水比例，通過冷凍乾燥制備pt / c的性能較好;採用液氮對預凍液進行冷凍（預凍溫度為- 196 ）制備的pt / c催化劑性能較好;冷凍乾燥法可以有效地避免加熱乾燥過程中前軀體離子在碳載體表面的脫附和團聚，進而制備載量大、分散性好、粒徑較小的pt / c催化劑。
  20. Compared to current object - oriented software component for distributed computing, software agent has bigger granularity and more intelligence, which becomes the research hotspot of current software technology, i. e. software technology changes from procedure - oriented to object - oriented, component - oriented and to agent - oriented

    與當今分散式計算的軟體構件技術（ com / dcom 、 corba和rmi ）的面向對象技術相比，軟體agent的粒度更大，智能化程度更高。軟體agent的研究已經成為當今軟體技術的研究熱點，也就是說軟體技術由面向過程到面向對象、面向構件，再到面向agent設計。
分享友人
分享到 Line

分享到臉書