過熱鍋 的英文怎麼說

中文拼音 [guòrèguō]
過熱鍋 英文
overheat pan
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 鍋 : 名詞1. （炊事用具） pan; pot 2. （裝液體加熱用的器具） boiler; cauldron3. （某些器物上像鍋的部分） bowl （of a pipe, etc. ）
  1. Manufacturers ' data report for watertube boilers, superheaters, waterwalls, economizers

    水管鍋爐過熱設備爐壁水管排和熱力裝置的生產商數據報告
  2. Effect of economizer heat transfer design and retrofitting on superheated steam temperature for the utility boiler

    電站鍋爐省煤器設計與改造對過熱汽溫的影響
  3. Gaz - fired central heating boilers. type b11 and b11bis boilers fitted with atmospheric burners of nominal heat imput not exceeding 70 kw

    燃氣的集中供熱鍋爐.公稱輸入熱量不超過70kw的裝有氣體燃燒器的b11和b11bis型鍋爐
  4. This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation

    本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。
  5. Through measuring residual swhirling flow field in the flue duct of a real boiler, and analysing layout features of front and back platen supe - heaters in large - scale tangential firing boilers, the flue gas energy distribution regularity in horizontal flue duct of tangential firing boilers has been studied

    摘要通過對實際鍋爐煙道煙氣殘余旋轉流場的測量及大型切圓燃燒鍋爐前、后屏過熱器的布置特點分析，研究了切圓燃燒鍋爐水平煙道煙氣能量的分佈規律。
  6. Uncontrolled superheat boiler

    不可調式過熱蒸汽鍋爐
  7. Has designed one boiler superheat vapor temperature online fuzzy pid double model control method based on this, and has given the detailed design proposal

    基於此設計一種鍋爐過熱蒸汽溫度在線模糊pid雙模控制方法，並給出詳細設計方案。
  8. Connecting with the practice of a certain power plant in shanxi province, this paper analyzes on the mechanisms and reasons of the leakages caused by the burst of high - temperature superheater tubes of the boiler, and advances some feasible measures for guaranteeing the normal operation of the boiler superheater

    結合山西某電廠實際，分析了鍋爐高溫過熱器爆管泄漏的機理、原因，提出了一些可行的措施來保證鍋爐過熱器的正常運行。
  9. A nonlinear mathematical model is developed to determine the flow rate distribution in the parallel tubes of boiler superheater and reheater by depending on the relation of pressure drop among individual tubes and accounting for the static pressure variations in the inlet and outlet headers

    根據並聯管組各根管子進、出口壓力降之間的關系，並考慮到分配集箱與匯集集箱中流體的靜壓變化，建立了鍋爐過熱器、再熱器流量分配的非線性數學模型。
  10. Traditional control system for boiler superheated steam temperature regulates desuperheating water flow through testing the superheated steam temperature and its variation trend, thus keeping the temperature of superheated steam within a permissible range

    摘要傳統的鍋爐過熱蒸汽溫度控制系統通過檢測過熱蒸汽溫度及其變化趨勢來調節減溫水量，從而維持過熱蒸汽溫度在允許的范圍之內。
  11. The article takes a 600mw natural cycle drum boiler ( soot blow using steam ) as investigating object, establishes soot accumulation loss and soot blowing energy loss models for its water cooling wall, superheater, economizer and air preheater respectively, set up instructions for soot blower operating. simulating calculation results are compared with site data to verify usefulness of key models. the article introduced the operation optimizing design of soot blowers of yanzhou no2 power plant based on theoretical research

    本文以600mw汽包自然循環鍋爐（蒸汽吹灰）為具體分析對象，分別建立其水冷壁、過熱器、省煤器、空預器的積灰損失和各受熱面吹灰能量損失的模型，建立相應的吹灰器運行規則指導，對設計中的關鍵模型問題，通過模擬計算及與現場數據作比較的方法，驗證其可用程度。
  12. For the limitation of the former soviet union boiler unit heating calculation standard methods in 1973 in the boiler furnace ， panel and platen superheater ， this paper puts forward the new methods of the boiler heating calculation

    分析了前蘇聯73年鍋爐機組熱力計算標準方法中爐膛、分隔屏過熱器和屏式過熱器計算方法的缺陷，初步提出鍋爐熱力計算新方法。
  13. Failure diagnosis after changing tube for last stage superheater of boiler

    鍋爐末級過熱器換管后失效診斷
  14. Which are higher than electric driven heat pump, gas boiler, coal boiler and electric boiler. the energy grade theory analysis results also show that the energy utilization of gehp is comparatively reasonable. exergy cost of gehp is 11. 2 yuan / gj by thermoeconomic method, which is much lower than the heating price nowadays

    對比發現，燃氣機熱泵的一次能源利用率和（火用）效率均高於電動熱泵、燃氣鍋爐、燃煤鍋爐和電鍋爐；對燃氣機熱泵系統的能級分析也表示系統的能量利用過程比較合理；通過熱經濟學的分析，得出燃氣機熱泵的供熱（火用）成本為11 . 2元gj ，這個價格與現行集中供熱的價格相比還是很有優勢的。
  15. This temperature calculation method avoids the non - correspondence between the flow rate and heat flux, which may exists in that used by boiler manufactures, and was employed to calculate the tube temperature of dangerous position that concerns with the retrofit scheme of superheater 1 of tower type coal - fired 330 mw once - through boiler in pucheng power plant for 100 % and 50 % operation load

    針對蒲城電廠330mw塔式燃煤直流鍋爐1號過熱器的改造方案，利用本文提出的方法與電廠鍋爐常用的壁溫計算方法分別計算了100 %與50 %鍋爐運行負荷下危險部位的壁溫。
  16. For manufacture water cooling panels, coal - saving devices, reheaters, superheaters and steam pipelines of boilers

    用於鍋爐水冷壁、省煤器、再熱器、過熱器和蒸氣管道的製造。
  17. Analysis on the reason of pipe fracture caused by boiler ouerheat

    鍋爐過熱器蛇形爆管原因分析
  18. The application study is carried out for the pid parameter optimal adjustment for the boiler steam temperature control system of a power plant

    對某電廠300mw直流機組鍋爐過熱汽溫控制系統的參數優化整定進行了應用研究。
  19. The mainly works had been done as follows : 1. in order to keep commonality, the modules who have similar thermodynamic process had been classed. such as evaporating module ( including furnace, drum, system of boiler recycled water ), single - phase heat exchange module ( including superheater, reheater, ecomomizer ), lubricating oil system module ( can be used for any lubricating oil system of rotation mechanical impedance ), pump and fan module, ect

    本文所作的主要工作如下: 1 、為保證模塊的通用性，對鍋爐有相似熱力環節的模塊進行分類，建立模塊庫，便於模塊調用，如蒸發區模塊（包括爐膛、汽包和爐水循環系統） ，單相換熱模塊（包括過熱器，再熱器，省煤器等） ，潤滑油系統模塊（可用於各種轉機軸承潤滑油的動態特性的計算） ，泵與風機的動態計算模塊等。
  20. After appropriate reform measures were taken, the slagging and gas temperature deviation problemes have been completely solved. the boiler efficiency was raised by 2 percentage points and the boiler ' s safety and economics effect got improved

    鍋爐經本次改造解決了爐膛出口煙溫偏高的問題，實現了鍋爐在130t h的額定工況下低溫段過熱器前煙溫由大修前的936下降到825的預期效果，並提高爐效2個百分點，使鍋爐運行的經濟性和安全可靠性得到改善和提高。
分享友人
分享到 Line

分享到臉書