適佳范圍 的英文怎麼說

中文拼音 [shìjiāfànwéi]
適佳范圍 英文
comfort zone
  • 適 : 形容詞1 （適合） fit; suitable; proper 2 （恰好） right; opportune 3 （舒服） comfortable; well Ⅱ...
  • 范 : 名詞1 [書面語] （模子） pattern; mould; matrix 2 （模範; 榜樣） model; example 3 （范圍） boundar...
  • 圍 : Ⅰ動詞1 （四周攔擋起來 使裡外不通; 環繞） enclose; surround; corral 2 （繞; 裹） wrap Ⅱ名詞1 （四...
  • 范圍 : scope; limits; extent; boundary; confines; range; range dimension; spectrum
  1. This paper analyzes the factors affecting the controlling precision of sand compactibility system and sets up the dynamic model of regression coefficient between sand compactibility and water content. to prevent the insufficiency or excess of sand water content, the amount of the first addition is set as 80 % of the total water addition amount. after the first water addition, we adopt ar model to predict the stable value of sand compactibility to shorten the time mixing the sand. each time we add water, the correction coefficient is introduced to adapt to the change in the composition of sand. the experiment shows that the mathematics model not only makes the water content in sand reach the best range within shorter time, but also directs how the sand composition should be adjusted, which can better conform to the actual situation

    分析了影響型砂緊實率控制精度的因素，建立了型砂緊實率-水分回歸系數的動態模型.為防止型砂水分不足或過量，將第一次加水量設定為總加水量的80 .第一次加水后，對型砂緊實率穩定值採用ar模型進行預測，以縮短型砂混制時間.每次加水后，引入修正系數，以適應型砂組成的變化.實驗表明，該數學模型不僅使型砂水分含量在較短時間內達到最佳范圍，同時可指示對型砂組成進行調整，能較好地符合實際情況
  2. In this paper, the effects of fly ash, cement, lime, fine sands, foam agent, w / c ratio and additional agent on foamed concrete were studied by experiments, the best combination ratio of fly ash foamed concrete whose density varies from 551kg / m3 to 650kg / m3 was obtained through orthogonal test design, the foam agent quantity and the fly ash quantity effect the fly ash foamed concrete greatly, so the author selected them as independents to establish duality linear regression equations, the equations were quite ideal through the test of model summary r. moreover, the author also did some experiments about the water resistance of magnesium oxychloride cement fly ash foamed concrete, the outcome showed that phosphoric acid has good effect on water resistance, and its appropriate quantity was found

    本文通過試驗研究了粉煤灰、水泥、石灰、細砂、發泡液、水灰比及外加劑對粉煤灰發泡混凝土性能的影響，採用正交設計試驗方法得出了600級粉煤灰發泡混凝土的最佳配合比，同時發現發泡液和粉煤灰摻量對發泡混凝土的影響最為顯著，因此，以二者為自變量建立了二元線性回歸方程，通過全相關系數的檢驗發現方程較為理想。此外，還對氯氧鎂水泥基粉煤灰發泡混凝土的耐水性進行了相關實驗，發現磷酸有較好的耐水性效果，同時找到了其合適的摻量范圍。
  3. In the volume change study, we found appropriate temperature is helpful for shrinkage control, and different lpas have different shrinkage control effects due to their dipole moment, tg, miscibility with upr and morphology after blending. there existed an optimal concentration range of poly ( vinyl acetate ) based lpas for shrinkage control. lpa was effective for shrinkage compensation in this range, on the other hand, lpa only acted as filler and the low profile effect vanished out of this range, however, for polystyrene based lpa, the more concentration the better shrinkage control

    在膨脹研究中，發現適當的溫度條件更有利於upr達到好的收縮控制效果；不同類型的lpa隨著偶極矩、玻璃化溫度、與upr的相容性、與upr的混合形態的不同，表現出不同的收縮控制效果；聚醋酸乙烯酯類的lpa - a存在一個最佳收縮控制的濃度范圍，在這個范圍之內， lpa起到補償收縮的作用；而在這個范圍之外， lpa的作用僅相當于填料，不能起到收縮控制。
  4. A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle

    試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。
  5. The grade composite, road performance and its mechanism are systemically studied. 1 ) the aggregate grade of ogfc is studied through the volume method base on the analysis of the aggregate grades. then the grade is verified and the relation between the grade and pore rate is studied statistically, the typical grades of ogfc are developed ; 2 ) the reasonable pore rate of ogfc is studied on the basis of the balance of mechanics and function performance ; 3 ) the mineral fiber is added to the ogfc mixes to increase asphalt content, thus the anti - water performance of ogfc mixes are improved ; 4 ) high viscous asphalt fit for the preparation of ogfc is prepared through composite modification by sbs and rubber powder ; 5 ) the mechanics mechanism of ogfc is studied in the paper, it shows : asphalt paste, as well as the coarse aggregate skeleton, is essential to the mechanics of ogfc

    在分析各國ogfc級配的基礎上，運用礦料體積法進行ogfc級配設計，用正交實驗對礦料級配進行了優化設計，運用數理統計方法分析礦料級配和孔隙率之間的關系，並回歸出礦料關鍵篩孔通過率與ogfc骨架空隙結構關系的數學方程，進而提出了ogfc的合理級配；通過對不同孔隙率典型級配混合料的性能研究，綜合力學和功能性能，得出了ogfc的合理孔隙率范圍：針對高速公路面層對ogfc力學性能方面的要求，本文從瀝青膠結材料、纖維穩定劑兩方面對ogfc的性能進行改善：通過sbs和橡膠粉復合改性的方法開發出了適合ogfc的高粘度改性瀝青，摻加聚合物纖維，提高ogfc的最佳瀝青用量，進而改善了混合料的高溫性能和抗水損害性能，優化設計出能滿足高速公路路用性能，車轍動穩定度達5000次/ mm以上，動融劈裂強度比90 ，透水系數31ml / s ，並具有防滑降噪功能的開級配瀝青磨耗層（ ogfc ）混合料。
  6. Conclusions are drawn as follows : ( 1 ) regulating the electromotor speed by adjusting the input voltage is easy to carry out, and it can be used in most of the oil fields ; ( 2 ) good energy - saving effect can be achieved under the condition of light load on the motor ; ( 3 ) the voltage cannot be regulated in a large range, and the optimal range of the voltage regulation is less than 10 % of the rated voltage

    由此得出結論： （ 1 ）調電動機端電壓調速方法簡單，一次性投資少，易於實現，對於一般的油田都適用； （ 2 ）調壓調速只有在輕負荷時，即在負荷遠未達到滿負荷時才有一定的節能效果，適用於油田普遍存在的「大馬拉小車」的情況； （ 3 ）電動機調壓調速的范圍不能太大，電壓調整的最佳范圍為額定電壓的10 %以內。
  7. Finite difference time - domain method is used to calculate the reflection for these probes and absorbing boundary condition is used to deal with the singularity in the axis of the coaxial - line in the simulation. by comparing the reflection of different probes, the best probe has been selected according to sensitive requirement. the influence of parameters : such as thickness of protective film, length of protruding inner conductor of the coaxial - line probe to the measurement has been studied

    通過時域有限差分法進行數值模擬分析，並採用吸收邊界處理同軸線軸心奇異點，計算出各種探頭測量相同溶液的反射系數，根據其測量的靈敏度，選出最優設計；並通過分析所選探頭的各種設計參數，如薄膜厚度、內導體伸出長度等的變化對測量結果的影響，找出該探頭各參數的最佳范圍，使其具有高度靈敏性，以適用於測量化學反應溶液的介電常數。
  8. The main work of this paper was as fellows : ( 1 ) generalized the development of pre - stressed steel structure in our nation and abroad, and pointed out the main problem in practice ; ( 2 ) presented the mechanism of pre - stressed steel structure and revealed its applicable range ; ( 3 ) established the optimization design model for pre - stressed steel structure, which accounts for constraints on stresses and displacements of structure ; ( 4 ) brought forward the optimization design method, which combined linear programming and the principle of full restriction, through which we can obtain the magnitude of each time pre - stress and the optimized sections of each members of structure ; ( 5 ) analyzed the best times of pre - stress and pointed out that 2 ~ 3 times is preferable ; ( 6 ) conducted optimization design on large - space steel roof, horizontal parallel steel truss with local cables, horizontal parallel steel truss with global cable, and ultra - static steel truss, the result of which indicated that the multiple pre - stress structure is very economic ; ( 7 ) compared different schemes of cable placement for horizontal parallel steel truss, and the results showed that the local cable only unloaded the second girders, but had no response on the first girders and stomach poles, while global cable could unload the second girders and the stomach poles outside of turning point of cable, thus proving that global cable is more economic than local - cable

    本文的主要工作是：對國內外預應力鋼結構的發展歷史及現狀作了綜述和總結，指出當前預應力鋼結構工程實踐中存在的主要問題；闡述了預應力鋼結構的受力機理，並指出預應力鋼結構的適用范圍和特點；在考慮結構應力和變位約束的條件下，建立預應力鋼結構優化設計模型；提出多次預應力鋼結構優化設計方法和步驟，採用線性規劃和滿約束準則相結合的優化方法，可優化設計出施加的每一級預應力的大小，並得到結構各部分的優化截面；對多次預應力最佳的施加次數作了分析，並建議以2 3次為宜；為驗證文中理論和方法，分別對大跨多次預應力鋼屋架、局部布索的水平平行弦鋼桁架、整體布索的水平平行弦鋼桁架和局部布索的超靜定鋼桁架等算例進行了優化設計，經濟效益明顯；對水平平行弦鋼桁架的幾種施加預應力的方案進行比較，對于局部布索，預應力只對下弦起到卸載作用，對上弦和腹桿基本不起作用；而整體布索預應力除對下弦卸載外，對索折點以外部分腹桿也起到卸載作用，經濟效益好於局部布索。
  9. Abstract : the paper analyzes the wear resistance and anti - adhesion of 20 and 45 steel formed in austenitic ion - nitrocarburising and comparisons to the general ion - nitrocarburising. the experiment shows that austenitization - nitrocarburising can be carried out at 590 700, its wear resistance and anti - adhesion is the best at 630 ， the worst at 660 and anti - adhesion is the best at 630 ， the worst at 660 and the mediate at 570 600. with the help of raising processing temperature properly and speeding up the process the wear behavior can be improved

    文摘:研究20鋼、 45鋼經奧氏體離子氮碳共滲后的耐磨性和抗咬合性，並與普通離子氮碳共滲后的作了比較，試驗表明:在570 700范圍內進行離子氮碳共滲后，其耐磨性和抗咬合性以630處理時為最佳， 660處理時最差，而570 600處理時則介於兩者之間，通過適當提高共滲溫度，再提高滲速，從而縮短共滲時間的同時，可以提高耐磨損性能。
  10. In chapter 3, we studied the effect of gaussian transverse profile for the driving and laser fields on lasing without population inversion ( lwi ) in a closed v - type system and an open v - type system. moreover, we discussed also the effect of the unsaturated gain coefficient, the cavity - damping rate, the ratio of the atomic injection rates and atomic exit rate on the corresponding systems. in chapter 4, we mainly discussed the effect of doppler broadening on the gain, dispersion and the frequency up - conversion of the open v - type lwi system and compared the differences and the same between the open system and the corresponding closed system

    發現： （ 1 ）在考慮doppler展寬的情況下，通過選取合適的實驗室條件（比如合適的原子環境溫度等）可得到合適doppler展寬值，從而使系統獲得最佳增益； （ 2 ）要想實現系統的頻率上轉換，同時又要獲得足夠強的無反轉激光增益，則系統頻率轉換比不能選取的太大； （ 3 ）對于開放系統，比較小的粒子注入速率比與退出速率對產生無反轉激光是有利碩士學位論文摘要的： （ 4 ）由於dopp1oy展寬的存在，當探測場與驅動場的傳播方向相反時，增益在探測場失諧的某一段區域產生振蕩，且振蕩的振幅、頻率失諧范圍的大小與dopper展寬的取值有關。
  11. The authour investigate the dosing conditions and effect of the pac to the huanghe water - source, which includes the following four parts : the selection of the pac ; the confirmation of dosing scheme and effect of the pac ; the research of application of potassium permanganate in combination with pac ; the research of the pac ' s modification and the modified effectiveness. the experiment is mainly carried out on the pilot system in the jieyuan water plan of tianjin. the results of the reseach include the following : l ) the pac from zunhua plant is selected as the better carbon for the source water of tianjin through the experiment ; 2 ) through the pilot experiment we conclude that the pac ' s best adding point is the mixing tank and the better dose is 10mg / l, on which the codmn of filtered water can be decreased to 40 % and the effluent have no problem of odour and color ; 3the adsorbing experiment show that pac mainly adsorb the organic matters which molecular wt., distribution between 500 and 3000, and can adsorb organic matters whose molecular wt., distribution are bigger than 6000 if the dose of it is adequent ; 4 ) pac together with potassium permanganate can remove the organic matter more effectively than each of them alone, and reduce the rising trend of turbidity of the flotation ' s effluent due to adding pac ; 5 ) the thesis made a research on the surface properties and the adsorbing capability of the modified carbon by oxidizer : the modified carbon with 20 % h2o2 can remove more organic pollutants than the untreated one by 12 % when we add a higher dose of coagulant ; 6 ) the modification of reduction and loading metal ions are also sttldied, and drow the following conclusions : the modified carbon with 5 % ammonia can enhance the organic matter ' s removal effectiveness by 10 % to the tianjin source water than the untreated one, and the modified one with loading metal ion remove the organic matters from the tianjin source water better ( 8 % ) than the untreated one due to the strong affinity betwween the humic acid and copper ion

    本文的實驗主要是在天津芥園水廠的中試系統上完成的，論文的成果和結論主要包括： 1 ）通過靜態實驗選定河北遵化活性炭廠生產的煤質炭為適合天津原水的炭種； 2 ）中試實驗確定粉末活性炭的較佳投加點為混合池投加，較佳投加量為10mg l ，此時可使濾后水的cod _ （ mn ）降低40 ，且可較好地控制濾后水的嗅味和色度； 3 ）初步確定粉末活性炭對原水中有機物的吸附主要集中在分子量在500 - 3000范圍內，投量增大時可吸附部分分子量大於6000的有機物4 ）中試實驗表明：粉末活性炭與高錳酸鉀聯用可取得較兩者單獨應用時對有機物更好的去除效果，且對因投加粉末活性炭而造成的氣浮出水濁度升高有一定的改善作用； 5 ）研究並初步確定氧化改性對粉末活性炭表面性質和有機物的去除效果的影響：粉末活性炭的氧化改性會使其表面的酸性官能團大量增強，表面極性增加；經20的過氧化氫改性的活性炭在增大混凝劑投加量（ fecl _ 3投量為15mg l ）時對有機物的總體去除效果較原活性炭提高12 ， 1次氯酸鈉改性活性炭對有機物的去除效果較原活性炭提高6 ； 6 ）研究並初步確定還原改性、負載金屬離子對原水中有機物的去除效果的影響：經5氨水改性的活性炭可提高天津源水中有機物的去除率達到10 ；負載銅離子后的活性炭可提高對腐殖酸類物質的去除能力，一般可提高8左右。
  12. From three - wave coupling equations, the optimal crystal length, conversion efficiency and parametric light pulse width are computed numerically when clbo is used in picosecond optical parametric amplification. the results present that clbo are suited for optical parametric amplification in short wave band. in order to get higher conversion efficiency, the crystal length should be optimized according to the intensities of pump and signal waves

    從三波耦合方程出發，對clbo用於皮秒級光參量放大時，最佳晶體長度、轉換效率和參量光的脈沖寬度進行了理論分析和數值模擬，結果表明clbo晶體適合在短波范圍作光參量放大，為達到高的轉換效率和窄脈寬的信號光輸出，泵浦光和初始入射信號光的強度應根據晶體長度取最優化值。
  13. Good flatness, wide range of firing temp, suitable for high - gloss floor tiles in single firing process

    平整度佳，燒成范圍寬，適用於一次燒成高亮度地磚。
  14. The second phase it uses the ahp to select the right partner on considering the factors that influence the decision. the third phase it uses the dea to select partner from the candidate. the last phases it uses the portfolio and the multi - object theory to combine the partner

    第一階段利用粗選確定夥伴選擇的論域范圍；第二階段利用初選，採用層次分析法（ ahp ） ，綜合考慮影響決策的各類因素，篩選出合適的合作夥伴；第三階段精選，採用dea方法對候選夥伴進一步篩選；第四階段利用優化組合，用多目標理論對所選擇的合作夥伴進行最佳組合決策。
  15. Secondly, comparing with the algorithm that was given by english scholars a. k. nandi and e. e. azzouz in 1995, this dissertation presents a modified automatic recognition algorithm of six kind of digital modulation types such as 2ask, 4ask, 2psk, 4psk, 2fsk and 4fsk, which only uses four key features, and has a very great exaltation in the rate of correct recognition and the performance of signal to noise, we puts forward the constitution of the best threshold which is applicable to the signal that changes within the scope of the signal to noise rate ( snr ) from 5db to 30db, and the overall success rate is not lower than 92 % when snr is over 7db

    其次，針對1995年英國學者a . k . nandi和e . e . azzouz提出的針對2ask 、 4ask 、 2psk 、 4psk 、 2fsk和4fsk這六種常用的數字調制信號識別的演算法，提出了一種數字信號調制方式識別演算法（ dmra ）的改進演算法。該演算法僅利用四個特徵參數，就可以識別這六種調制方式，而且在調制識別率和信噪比性能上都有了很大的提高，能夠在信噪比不低於7db時，對實際信號的識別正確率高於92 % 。並且提出了最佳門限的設置方法，設置的門限適用於信噪比在5db ~ 30db范圍內變化的信號。
  16. In the portion of research on wavelet analysis based methods for multiresolution representation, simplification and rendering of terrain models, a three step approach to the choice of appropriate wavelet transform and the best wavelets according to application requirements is propsed : the first step chooses the type of wavelet transform, the second step determines candidate wavelets by picking out satisfying wavelet characteristics, and the last step selects the best wavelets from the candidates through wavelet parameterization

    在對基於小波分析的地形多解析度表示、簡化和繪制演算法的研究中，提出了一種根據應用需求分三步選擇合適的小波變換和最佳小波的方法：第一步是選擇小波變換的方式，第二步是通過明確合適的小波性質來確定候選小波的范圍，第三步是在候選范圍內通過小波參數化來遴選最合適的小波。
  17. Fine material to be dewatered is fed to the small end of a revolving cone shaped screen basket. solids retained on the screen are transported out of the basket through the angle of inclination and the wiping action of a scroll rotating at a slightly higher speed. with this wiping action, there are no large off - center movements due to uneven distribution of the material in the basket

    該機適用於化工制藥食品冶金礦山等行業固液分離，分離懸浮液固相在10 % 80 %固相顆粒直徑在0 . 135mm 0 . 22mm效果尤佳范圍內的線狀或結晶狀的固體顆粒，如檸檬酸，古酸鹽果汁硫銨尿素等。
  18. The filter has big filter area, byg flow, and wide application scope, so it is widely used in pharmacy, chemical engineer - ing and food industries. while used for filtering injection liquids in pharmaceutical factories, it has particularly good effects

    本機過濾面積大，流量大，適用范圍大，所以在制藥、化工、食品等行業有廣泛用途，應用在制藥廠針劑藥液之過濾，效能甚佳。
  19. Corresponding soluble salts have been chosen as raw materials and ammonia as precipitator. the optimum ph value is 8. 5 - 10 and higher concentration is helpful for crystal growth. the perovskite phase plzst can be synthesized at 750 by solid state reaction

    合適的工藝條件為：選擇以各離子的可溶性鹽為原料，以氨水為沉澱劑，通過共沉澱得到白色無定型前驅體，最佳的ph值范圍為8 . 5 10 ，溶液的濃度越高越有利於固相反應合成中晶體的形成，適當的沉澱后處理過程如水洗、干磨能促進plzst晶體的生成。
  20. We have earned a worldwide reputation for providing a full line of quality products and professional solution to meet the demands of our customers, helping them to save money with optimal overall system performance and occupant comfort

    我們提供全線的高質量產品和專業的解決方案來滿足顧客的各類需求，實現最佳運行方案和最舒適的環境並節約成本，在此方面我們在國際范圍內享有盛譽。
分享友人
分享到 Line

分享到臉書