部件結束狀態 的英文怎麼說

中文拼音 [bùjiànjiēshùzhuàngtài]
部件結束狀態 英文
device end condition
  • 部 : Ⅰ名詞1 （部分; 部位） part; section; division; region 2 （部門; 機關或組織單位的名稱） unit; mini...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 束 : Ⅰ動詞1 （捆; 系） bind; tie 2 （控制; 約束）control; restrain Ⅱ量詞（用於捆在一起的東西） bundle;...
  • 狀 : Ⅰ名詞1 （形狀） form; shape 2 （情況） state; condition; situation; circumstances 3 （陳述事件或...
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 部件 : component; unit; parts; assembly; subsystem; secundina （pl. secundinae）
  • 結束 : finish; closure; foreclosure; end; terminate; conclude; wind up; close; come to an end; come to a...
  • 狀態 : status; state; condition; state of affairs: （病的）危險狀態 critical condition; 戰爭狀態 state o...
  1. A full mathematical model of optimal flow pattern design withengineering constraints was put forward, based on modern optimal control theory. an optimal flow pattern design was presented for optimizing meridional channel of axial flow turbine. according to integral optimization of turbine stages, a full physical model and mathematical expression were put forward for proposition of optimal flow pattern, including all performance parameters in turbine stages. this problem was further recast into a typical form control to maximize specific performance index such as work or efficiency of stage with given initial state, fixed terminal condition and constraints for part of state terminal variables. the program was also worked out according penalty function method and conjugate gradient method. the optimal distribution of c1ur1 ( r1 ) was obtained according to constraint conditions and maximized objective function

    把近代最優控制論方法引入軸流透平葉片的設計，在優化的軸流透平子午通道內，建立包括透平級內所有性能參量的最優流型命題的完整的物理模型及其數學表達式，並歸化為一個在給定初始狀態、自變量終端固定、部分狀態變量終端受有約束的條件下，使級的某一性能指標（如級的功率）達到最優的最優控制問題，應用「代價函數法」及「共軛梯度法」編制計算程序，計算得到符合給定約束條件、並使目標函數取極值的最優環量分佈，結果是令人滿意的。
  2. For the feedback controller design, under the condition of that the noise and disturbance had been eliminated through disturbance observer, an anti - windup state feedback controller is proposed to solve the problem in which most of the existing anti - windup schemes can not guarantee the asymptotic closed - loop stability even for open - loop stable systems subjected to actuator saturation

    對于反饋控制器設計，考慮了系統的物理約束即驅動飽和的影響，在系統的量測噪聲和外部擾動已經通過擾動觀測器減弱的條件下，提出了一種抗漂移的狀態反饋控制器設計方法。模擬結果表明所提方法的有效性。
  3. This orientation plays a key role in determining the mechanical and physical properties of the finished product. therefore, it is very important to have some insight into the change of fibre orientation during flow

    在流動結束后，纖維的最終取向也將保留在固體部件中，纖維的取向狀態對部件的力學和物理性能都有很大的影響。
  4. According to virtual prototype simulation course, we can get constraint con - dition and receiving strength state of thigh, calf, arm and u fork, consequently carry on modal analysis of thigh and calf as well as arm. then carry in effect the

    最後根據虛擬樣機模擬過程，可以獲得大腿、小腿、大臂、小臂和u型叉的約束條件以及受力狀況，從而對大腿、小腿和大臂、小臂進行模態分析，以及對u型叉、髖部十字軸等部件進行應力分析並且提出結構的合理改進。
分享友人
分享到 Line

分享到臉書