部分固端梁 的英文怎麼說

中文拼音 [bùfēngùduānliáng]
部分固端梁 英文
partially fixed beam
  • 部 : Ⅰ名詞1 （部分; 部位） part; section; division; region 2 （部門; 機關或組織單位的名稱） unit; mini...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 固 : Ⅰ形容詞（結實; 牢固; 堅硬） firm; hard; solid Ⅱ副詞1 （堅決地; 堅定地） firmly; resolutely 2 [書...
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 梁 : 名詞1 （屋架中架在柱子上的長木） beam 2 （通常也指檁） purlin 3 （橋） bridge4 （物體中間條狀隆起...
  • 部分 : （整體中的局部或個體） part; section; portion
  • 端梁 : end beam; end girder; end sill
  1. Consideration of the additional axial, two angular deformations generated by the bond slipping in anchorage zones of joints, the assumption is made, that the plane section of either end of a member before bond slipping of reinforcements remains afler bond slipping of reinforcements. additional deformations * contribution to stif ? nesses of plastic sub - elements is formed from the boundary nonlinearity of plastic stabelements. the space bond slip relation can truly compute bond slip in anchorage zones, additional def ? rmatinns, and their contribution to the space nonlinearity of a niember, has used iii space nonlinear analysis of columns and spandrel beams in this dissertation

    附加變形對塑性子區域的剛度貢獻，看作是塑性子區域的邊界非線性，建立了構件端部子區域基於構件邊界非線性的鋼筋與砼之間的空間粘結滑移關系，能較真實地求得錨固區的粘結滑移、附加變形以及他們對構件空間非線性性能的貢獻，並運用於柱、裙梁的空間非線性分析之中。
  2. Regarding the rc beams subjected to concentrated load or even load and braced by bonding steel, an analysis is made on the relevant factors influencing maximum anchorage shear stress of steel sheet. the analysis is based on elastic theory and makes use of the formula for calculating anchorage shear stress of steel sheet. as indicated by the results, the maximum anchorage shear stress not only realtes to such parameters as height of cross section of rc beam and span but also relates to the thickness of adhesive layer, elastic modulus, thickness of steel sheet, and length of steel sheet. the present method will check maximum an chorage shear stress on the end of shear sheet so as to prevent rc beam from local damage. the present results will offer important reference for our country to further perfect bracing design by bonding steel method

    在彈性理論的基礎上，利用鋼板錨固剪應力計算公式，對在集中荷載或均布荷載作用下採用粘鋼加固的混凝土梁，分析鋼板錨固最大剪應力的有關影響因數.結果表明，最大錨固剪應力不但和混凝土梁的截面高度、跨度等參數有關，還和粘膠層厚度、彈性模量、鋼板厚度及鋼板長度有關.採用文中方法可以對鋼板端部最大錨固剪應力進行驗算，防止混凝土梁出現局部受拉破壞.研究結果為進一步完善我國粘鋼法加固設計提供重要的參考資料
  3. The following principles are proved : increasing cfp adhesive length will release the concentrating of shear stress near the cutoff point, this will lead to the increment of loading - bear capacity of concrete beams ; increasing the thickness of cfp will improve the transition of load from concrete beam to cfp, this is useful to exert the potential of cfp ; in creasing the anti - shear modulus of adhesive will result enhance the concentrating of shear stress, this is harmful to the effect of cfp reinforced concrete beams

    本文的理論分析結果可以表明：增加碳纖維板的粘結長度可以緩解碳纖維板端部界面上的剪應力集中，改善混凝土梁結構的加固效果；增大碳纖維板的粘結厚度可以增大界面上的剪應力，改善混凝土樑上載荷向碳纖維板的傳遞效果，有利於充分發揮碳纖維布的潛能；如果粘結膠層的抗剪模量過大會加劇剪應力的集中，從而對碳纖維加固的效果不利。
  4. This article theoretically analyzes the stress concentration at the area of plate end, calculates the values of the stress with the software of ansys and gets the distributing curves of the stress at this area. some suggestions about the anchorage are proposed in this article according to the calculating result

    本文對加固后的梁在受力時碳纖維布的端部應力集中現象進行了理論分析，並應用anysis有限元計算軟體進行了計算，得到了碳纖維布端部應力的分佈曲線。
分享友人
分享到 Line

分享到臉書