金屬搭接 的英文怎麼說

中文拼音 [jīnzhǔjiē]
金屬搭接 英文
metallic bone
  • 金 : Ⅰ名詞1 （金屬） metals 2 （錢） money 3 （古時金屬制的打擊樂器） ancient metal percussion instrum...
  • 屬 : 屬名詞1 （類別） category 2 [生物學] （生物分類系統上所用的等級之一） genus 3 （家屬; 親屬） fami...
  • 搭 : 動詞1 （支; 架設） put up; build 2 （把柔軟的東西放在可以支架的東西上） hang over; put over 3 （...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 金屬 : metal
  1. Destructive tests on welds in metallic materials - tensile test on cruciform and lapped joints

    金屬材料焊接的破壞試驗.十字形接縫和搭接縫的抗拉試驗
  2. Testing of adhesives for metals and adhesively bonded metal joints ; creep test on single lap joints

    金屬和粘結的金屬接點用的粘合劑的試驗.單搭接粘膠點
  3. Standard test method for thick - adherend metal lap - shear joints for determination of the stress - strain behavior of adhesives in shear by tension loading

    拉伸載荷法測定剪切中膠粘劑應力-應變性能用厚被粘物金屬搭接-剪切接頭的標準試驗方法
  4. Adopt advanced technic of f4 whole cold - press to moulding and heat melt to process to make, let the lining no slot to link withal cheek by jowl connect with exterior metalpipes wall, in the state of allowwing to work keep to distort in - phase, thereby to enhance using - life of lining in the working status of opposite high temperature high vacuum, stop the ecumenic pad fluorin pipes using in condition of cold and heat alternate and minus tension to come into being the matter of padding fluorin floor shrivel to jam the flowway and plastic rip, its perfect choice use to transport medium of strong corrosive strong oxidation by modern chemical - industry corporation

    採用氟塑料f4整體冷壓成型及熱熔加工等先進技術製造，使內襯層無縫搭接且與外層金屬管壁緊密粘接，在允許工作狀態下能夠保持同步變形，從而提高了襯里層在相對高溫高真空度的工況下的使用壽命，杜絕了一般襯氟管在冷熱交替，及負壓的條件下使用易產生襯塑層鼓癟阻塞流道及塑料拉裂的問題，是現代化工企業在輸送強腐蝕強氧化介質理想的選擇。
  5. Standard test method for apparent shear strength of single - lap - joint adhesively bonded metal specimens by tension loading metal - to - metal

    用拉力負載法測定單面搭接粘結的金屬試樣表面剪切強度的標準試驗方法
  6. I. investigation on laser surface hardening for metal materials in this work, the effect of the process parameters in laser surface hardening on the properties and surface feature of the hardened layer was studied

    一、金屬材料激光表面硬化技術研究。研究了激光表面淬火工藝參數和硬化層性能、強化效果之間的關系，對大面積激光淬火技術的基礎理論及搭接方法對組織性能的影響規律進行了探討。
  7. The anti - burnout character was improved obviously after the metallization be made more thick. the analysis on the gaas mmic metallization which burnout has been occured proved that the main reason was that the metallization is too thin to endure the mechanical stress, so the collapse will trigger the circuits burnout

    對gaasmmic互連出現的燒毀現象的顯微分析表明，主要是空氣橋金屬化層過薄，尤其是搭接處易出現塌陷，金屬層加厚后，互連線的燒毀能力有明顯改善。
  8. Pressing sheet metal components in supporting reliable lap, lap length comply with design requirements and should not be less than the numerical standards

    壓型金屬板應在支承構件上可靠搭接，搭接長度應符合設計要求且不應小於規范的數值。
  9. Destructive tests on welds in metallic materials - tensile test on cruciform and lapped joints iso 9018 : 2003 ; german version en iso 9018 : 2003

    金屬材料焊縫的破壞試驗.十字形和搭接焊縫抗拉試驗
分享友人
分享到 Line

分享到臉書