釘頭 的英文怎麼說

中文拼音 [dīngtóu]
釘頭 英文
pin fin
  • : 釘動詞1. (用釘子固定) nail 2. (用針線縫) sew on
  1. Countersunk head screws - head configuration and gauging

    .部外形和測量
  2. A third time he approached in the same manner, when the christian knight, desirous to terminate this elusory warfare, in which he might at length have been worn out by the activity of his foeman, suddenly seized the mace which hung at his saddlebow, and, with a strong hand and unerring aim, hurled it against the head of the emir, for such and not less his enemy appeared

    第三次他又猛撲,這時基督教騎士不願老讓敵人用這種方式消耗白己力量,決定結束這種虛晃一著的戰斗,突然拿起放在馬鞍前穹上的釘頭錘狠命地一扔,錘準確地直指這個酋長的部(看起來這個敵人的身份不會低於酋長) 。
  3. Noted for his weapons skills, toede achieves expert status in spear, long sword and short sword, mace, morning star, longbow, short bow, dagger, rapier, poignard, staff, knife, bludgeon and truncheon, not to mention the martial arts

    由於他武器方面的技能,投德在長矛、長劍、短劍、錘棍、釘頭槌、長弓、短弓、匕首、細劍、銳匕、長棍、小刀、短棒、警棍方面都取得了專家的稱號,更不要提武術了。
  4. Operate guidebook : the ctrl attackstones for the big gun, the space attackstones for the nailhead hammer, the arrowhead acts, jumps up

    操作指南: ctrl為大炮攻擊,空間為釘頭錘攻擊,箭行動、跳躍。
  5. General purpose bolts and screws - radii under the head

    普通螺栓和螺釘頭下圓角半徑
  6. Fasteners. resistance welding screws. reduced head. symbol z sr

    緊固件.電阻焊金屬螺.縮小釘頭
  7. His weapons are the plough and the mace

    他的武器是犁和釘頭
  8. A lumi wields a golden morningstar with trained ease as it wades into melee

    光民熟練地揮舞釘頭錘加入戰團。
  9. Characteristics of flow resistance of pin finned drop - shaped tube at different attack angles

    流體攻角對滴形釘頭管流體阻力特性的影響
  10. Swords are not bludgeoning weapons like mace, staff or fist. hitting the target forcefully alone would not guarantee a cut

    刀劍不是像釘頭錘棍或拳那些撞擊性兵器,即使用力擊打也不能斬進目標的。
  11. While ffixing the board, firm the board from its center to the side. all the nails must be hidden into board

    固定板材時,應從一塊板的中部向長邊及短邊固定,子定位后,釘頭略埋入板內,但不得損壞板面。
  12. Methods of test for pallet joints - part 2 : determination of withdrawal and head pull - through resistance of pallet nails and staples

    托盤接的試驗方法.第2部分:托盤子和u形抗拔出和釘頭拉穿的測定
  13. He would hammer a nail into the wood with a series of blows that continued to down long after the head was flush with the boards

    他老是連續不斷地錘擊,把子敲進木,而且釘頭與板面平齊之後,還是一個勁兒地敲。
  14. Flat paper feeding, automatic steamatic streamline process of binding, paper folding and flat - pressing ; full set of imported electric appliances, plc programmable, and imported nail binding head

    平紙進料,自動裝訂、折頁,壓平流水作業;全進口電器配置, plc可編程;配進口訂釘頭
  15. The study results reveal some laws : ( 1 ) two failure modes exist in different obliquity slope and influence the internal force of soil nailing ; ( 2 ) the connection between face shield and soil nailing determines the distribution of the axial force along length ; ( 3 ) the influence of face shield involves its connection with soil nailing and its stiffness on soil nailing wall ; ( 4 ) the transversal effect of soil nailing depended on the joint of nail head is little ; ( 5 ) the maximum axial forces of other soil nailings except the first soil nailing increase gradually with excavation

    研究表明: ( 1 )素土坡隨著坡角的變化,存在兩種破壞方式,破壞方式不同,土受力狀態不同; ( 2 )土和面層的連接方式決定著土長度方向上的軸力分佈形態; ( 3 )面層主要通過面層與土的連接和面層的本身剛度兩個方面對土內力和墻體變形產生影響; ( 4 )土橫向抗剪抗彎作用的發揮程度和土釘頭的連接方式有關,但作用不大,實際設計時可以忽略其影響; ( 5 )隨著坡體的開挖,第一排土的最大軸力變化不大,其它土的軸力都穩步增加。
  16. 315 screws, normal hexagonal head, threaded to head, in titanium alloy, anodized, mos2 lubricated - classification - 1100 mpa at ambient temperature 315 c

    二硫化鉬潤滑的陽極化的鈦合金螺紋至螺釘頭部的標準六角.等級: 1100 mpa
  17. Nail head bonder

    釘頭式接合機
  18. 235 screws, pan head, slotted, threaded to head, in alloy steel, cadmium plated - classification - 900 mpa at ambient temperature 235 c

    鍍鎘合金鋼螺紋至螺釘頭的帶槽盤.等級: 900mpa
  19. 80 screws, pan head, slotted, threaded to head, in brass, tin plated - classification : 380 mpa at ambient temperature 80 c

    鍍錫的黃銅制的螺紋至螺釘頭部的開槽盤.等級: 380mpa
  20. 80 screws, 100 countersunk normal head, slotted, threaded to head, in brass, tin plated - classification : 380 mpa at ambient temperature 80 c

    鍍錫的黃銅制的螺紋至螺釘頭部的開槽100標準埋.等級: 380mpa
分享友人