針鉗 的英文怎麼說

中文拼音 [zhēnqián]
針鉗 英文
pin vice
  • 針 : Ⅰ名詞1 （縫衣物用的工具） needle 2 （細長像針的東西） needle like things 3 （針劑） injection; sh...
  • 鉗 : Ⅰ名詞1 （鉗子） pincers; pliers; tongs 2 （姓氏） a surname Ⅱ動詞1 （夾住） grip （with pincers）...
  1. There are various tactics or methods for giving effect to this principle, such as dispersion and concentration of forces, diverging advance and converging attack, the offensive and the defensive, assault and containment, encirclement and outflanking, advance and retreat

    執行這個方針，有兵力的分散和集中、分進和合擊、攻擊和防禦、突擊和鉗制、包圍和迂迴、前進和後退種種的戰術或方法。
  2. Medical instruments - trocar holding forceps type vogel

    醫療器械. vogel型套針夾持鉗
  3. Headers, pinch pointers, rolling machines, splitting machines

    鐓鍛機，鉗子指針器，滾壓盤，開口盤
  4. When the glue is set, remove the pins or clamps, trim the bare ends of the feather and bind them with thread for extra safety

    當膠是的時候放置，除去大頭針或螺絲鉗，整齊羽毛的赤裸結束而且為額外的安全用綁他們線。
  5. You then put glue on the base of you feather, pin or clamp one end to the shaft and wrap the feather around the shaft until you can pin the other end

    你然後在橋的周圍把膠放在上對橋的你基礎羽毛，大頭針或螺絲鉗一端而且包裝羽毛直到你能用針別住另一端。
  6. Forceps for holding eye needles

    鑷式眼用持針鉗
  7. The simplest method is local with syringe needle thorn defeats verrucous body top after disinfection, will flexible verrucous small system is crowded go out or carry except ; or of the tweezers that use tooth, curved hemal qian ga lives flexible verrucous small system, pull out its, besmear next the iodine of 2, oppress slightly hemostatic

    最簡單的方法是局部消毒後用針頭刺破疣體頂端，將軟疣小體擠出或挑除；或用齒鑷、彎血管鉗夾住軟疣小體，將其拔除，然後塗2的碘酒，並稍加壓迫止血。
  8. General specifications for needle holders

    持針鉗通用技術條件
  9. Needle holder and forceps

    持針器和鉗
  10. Miniature needle holder

    微型持針鉗
  11. Infant needle holder

    嬰兒持針鉗
  12. Biopsy forceps with needle

    帶針活檢鉗
  13. Medical and surgical equipment. surgical instruments. forceps, needle - threaders and needle - holders. dimensions and tests

    外科醫療器械.鉗穿線管和持針器.尺寸和試驗
  14. A microgripper with the structure of dual cantilevers is designed to meet the task of microassembly, and the microgripper is driven by two piezoelectric bimorphs

    摘要針對微裝配任務設計了一種雙懸臂梁結構的壓電雙晶片微夾鉗，該微夾鉗由兩個壓電雙晶片驅動。
  15. And methods of modification are proposed, which are mainly presented on clamping circuit and method of compensating for the errors of count results. thus the performance of system can get further improvement

    在測試過程中，發現了現有實現技術的某些不足，並有針對性的提出了改進，主要體現在計時電路中的鉗位電路設計和脈寬補償思想，有利於進一步改善系統性能。
分享友人
分享到 Line

分享到臉書