釬桿長度的英文怎麼說

中文拼音 [hàngǎnzhǎng]
釬桿長度英文
run of steel

  • : 名詞(釬子) drill rod [steel]; borer
  • : 桿名詞(桿子) pole; staff
  • : 長Ⅰ形容詞1 (年紀較大) older; elder; senior 2 (排行最大) eldest; oldest Ⅱ名詞(領導人) chief;...
  • : 度動詞[書面語] (推測; 估計) surmise; estimate
  • 長度: length; longitude; size; extent; footage

※中文詞彙釬桿長度在字典百科國語字典中的解釋。

  1. A small extension curtain rod is an excellent support rod for plants. the length can continually be adjusted without disturbing the plants

    一個小的可以伸的窗簾是特別好的攀援植物種植。它的可隨著植物的生而連續地調整,對植物則沒有干擾。
  2. The beyond is the simple notation of serial number of pricker, totaled 7 digits of codes, in which the first digit represents the diameter of needle - bar of pricker, the second digit represents the siding of triangle side on functional section of pricker, the third digit represent the length of functional section of pricker, whereas in standard notation, it represents the distance from needlepoint to gradual deflating small port ( lower port ), the fourth digit represents the total length of pricker, which is the distance from the inside of bending helve to the needlepoint, the fifth digit represents the total quantity of dents on the cording of functional section, and the sixth digit represents the model of barb on functional section, while the seventh digit represents the distance between barbs on functional section

    以上為刺針編號的簡單寫法,共7位代碼,第一位是刺針針的直徑;第二位是刺針工作段三角面的邊寬;第三位是刺針工作段的,同標準寫法所不一樣的是針尖到漸縮錐小口(下口)的距離;第四位是刺針的總,按彎柄內側至針尖的距離;第五位是工作段棱上的總齒數;第六位是工作段上鉤刺的型號;第七位是工作段上鉤刺與鉤刺之間的距離。
  3. One, for instance, consisted of rods of various lengths and thickness which would stand up on end like ninepins.

    例如,有一種儀器由各種和粗細不同的木豎著構成,象九柱戲一樣。
  4. The analysis of precision about mould - cut main mechanism with clearances is advanced. on the basis of analysis of slider displacement error influenced by the crank length tolerance, the coupler length tolerance and clearances in revolute joints for mould - cut main mechanism, some reasonable suggestions about tolerance distribution of bars length and fitting precision of joints are put forward

    考慮運動副間隙對主切機構進行了精分析,通過分析主切機構中各誤差和運動副間隙對滑塊位移誤差的影響,對商標模切機設計初期誤差分配和運動副間隙配合精提出了合理的建議。
  5. The task consider geometry stiff matrix of suspenders due to adjustment of suspender length ( the actual suspender length is shorter than its nominal length ), and derive method and step of static tension of suspenders from single order variation

    本課題還考慮了由於吊索(的調整(實際的吊索(比名義短)而引入的吊索()系的幾何剛矩陣(初應力剛矩陣) 。
分享友人