鉆壓控制 的英文怎麼說

中文拼音 [zhēnyākòngzhì]
鉆壓控制 英文
weight control on drilling bit
  • 鉆 : 鉆Ⅰ名詞1. （打眼用的工具） drill; auger 2. （指鉆石） diamond; jewel Ⅱ動詞（用尖物在另一物體上轉動） drill; bore
  • 壓 : 壓構詞成分。
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. First this paper describes the composing and technics of drillers ; then the composing of control system based on s7 - 300plc is described ; then thinking of such characteristics of oil driller as complexity and long delay, this paper brings forward the control strategy of combining the fuzzy control with smith estimate control algorithm, and sets down the way of auto - driller based on discal hydraulic pressure brake. at last the experiment based on matlab by computer shows that the effect of this control mode is very good and all performance are famous

    首先本文闡述了鉆機的組成與工藝特點，然後描述了基於西門子s7 - 300plc的控制系統組成，然後針對傳統鉆機自動送鉆控制策略落後的缺陷，同時考慮到鉆機的復雜性、大滯后等特點，提出了模糊控制演算法與施密斯（ smith ）預估控制演算法相結合的控制策略，給出了基於液壓盤式剎車的自動送鉆智能控制策略， matlab的模擬實驗證明該控制方式控制效果良好，各方面性能指標都達到理想要求。
  2. Design of fluid drive and electrical control system for bore modular machine tool

    鉆孔組合機床液壓傳動和電氣控制系統的設計
  3. The subsea wellhead production system, named building block subsea system, adopts the most advanced technologies in the world, including the subsea horizontal christmas tree, electro - hydraulic control system, mudline booster pump, umbilical assembly, host, and rov, etc

    被稱為「組塊搭接式控制系統」的水下井口生產系統，薈萃了當今世界的尖端技術，包括雙定位水下臥式採油樹、電/液控制系統、泥線增壓泵、電纜系統、折疊式鉆井底盤系統和遙控作業機器人等。
  4. The main products of our company : series of mining emulsion pump station, series of electric haulage shearer, sparying pump station, series of mining flame - proof vacuum / air electromagnetic starter, series of mining vacuum / air feeding switch, series of mining fame - proof and natural - safe. type ac soft starter, series of hydraulic stand valve and pipe system, high flow rate quick - moving valve, the new product nearing into market - the hydraulic support electric - control system, mining electric drill, hydraulic valve test table, electric performance test table

    公司主導產品為：系列電牽引採煤機、系列礦用乳化液泵站、噴霧泵站、礦用隔爆兼本質安全型交流軟起動器、系列礦用隔爆真空、空氣電磁起動器、系列礦用真空、空氣饋電開關、系列液壓支架閥類及管路系統、大流量快速移架閥、即將投入市場的新產品? ?液壓支架電液控制系統、煤電鉆系列、液壓閥試驗臺、電性能試驗臺等。
  5. Based on the description on the construction technology of the continuous flight auger ( cfa ) pile, the quality advantage, material requirement, construction condition of the pile is introduced, and then the causation of the quality defect and its control measure are presented herein ; from which the processes of both the construction and the quality control are analyzed as well

    摘要基於對長螺旋鉆孔混凝土壓注樁施工工藝的論述，介紹了該類型樁的質量優點、材料要求、作業條件以及常見質量缺陷的原因及控制措施，對其施工及質量控制過程進行了分析。
  6. The distance of the single - row curtain grout hole is between 1. 4 to 1. 8 meter, and 2. 0 meter is suitable for the double - row curtain ; the grouting pressure generally is 1. 0 to 1. 5 mpa at the first three grout compartment, then grouting pressure of under the fourth control in 4 to 5 mpa ; for mast grout compartments, a water - cement ratio of 2 or 1 may used in the first grouting

    鉆孔密度也由原來的0 . slm / mz降至o . 64n擴mz ，節約工程投資447 . 35萬元。 6 、單排帷幕的孔距在1 . 4一1 . 8m之間，雙排帷幕的孔距以zm為宜;灌漿壓力在地表以下前三段一般為1一1 . smpa ，第四段以下按4一smpa控制;對大部分孔段而言，開灌水灰比可定為2或1 。
  7. On the basis of this, the hydraulic system of the mkd - 5s drilling machine is resigned for improvement. specially energy - saving design of the feeding system is made and the control characteristic of the electro - hydraulic proportional controlled system of feeding is studied both in theory and in experiment

    在此基礎上，應用電液比例技術對mkd ? 5s型鉆機液壓系統進行了改造設計，重點對給進系統進行了節能設計，從理論和實驗兩方面對給進加壓電液比例控制系統的特性進行了研究。
  8. The result of the study shows that the electro - hydraulic proportional technology is useful for all - hydraulic operated drilling machine to simplify the operations and composition of system, to improve the level of automatization and efficiency and to reduce the consumption of energy. the result of the study also shows that the system of feeding has the properties as followed : fast respone, stable pressure - adjusted characteristic, distinct effect of energy - saving, some improvement of system efficiency

    研究結果表明：全液壓鉆機中應用電液比例技術，可以簡化系統組成和操作，提高鉆機自動化水平，提高系統效率，降低發熱和溫升；採用恆壓變量泵的給進加壓電液比例控制系統調壓性能穩定、響應快、節能效果明顯。
  9. Specification for underbalanced drilling technology - part 2 : the outfit requirements of the wellhead pressure control and surface equipment

    欠平衡鉆井技術規范.第2部分:井口壓力控制裝置及地面裝置配備要求
  10. One of the key problems of designing the control valve of modulation rotary steering drilling tool is the design of high pressure hole of upside valve

    摘要設計調制式旋轉導向鉆井工具控制閥的關鍵問題之一是上盤閥高壓孔的設計。
  11. According to the work principle, mechanical model theory and simulation analysis of the hydraulic control valve of the drilling tool, the optimal design parameters of the angle of center of circle of the high pressure hole of upside valve are proposed ; the influence of the charging and discharging lag times on palm supporting capacity is discussed ; and the theoretic basis of designing the control valve of the drilling tool is put forward in the paper

    通過對調制式旋轉導向鉆井工具液壓盤閥機構的工作原理、力學模型的理論和模擬分析，給出了上盤閥高壓孔圓心角的最優設計參數；討論了充液、泄液滯后時間對巴掌支撐力的影響，提出了調制式旋轉導向鉆井工具控制閥機械設計和控制的理論依據。
  12. This pressure must be under control, and we control it by means of the mud which we circulate down the drill pipe

    這種壓力必須加以控制，而且我們控制壓力的方法是把泥漿灌注到鉆管中去。
  13. Automatic weight control

    鉆壓自動控制
  14. We exercise strict control over raw material purchasing and production process, so that the panels couple the toughness and hardness, which make future operation such as cutting, bending, pressing, drilling, fixing and edge shaping become easy

    本公司嚴格控制原材料采購及生產工藝過程板面強度極高，剛韌結合，可隨意切割，分條，彎弧，衡壓鉆孔，連接固定及邊部壓縮成型。
  15. 3excellent processing performance. we exercise strict control over raw material purchasing and production process, so that the panels couple the toughness and hardness which make future operations such as cutting, bending pressing drilling, fixing and edged shaping become easy

    本公司嚴格控制原材料采購及生產工藝過程，板面強度極高，剛韌結合，可隨意切割，分條，彎弧，衡壓，鉆孔，連接固定及邊部壓縮成型。
  16. By using the hydraulic torque converter to drive the mud pump, both the prime motor and the working machine can be protected, and the pump pressure can be controlled in the whole course of drilling if the rated rotary speed of the diesel engines is kept

    通過液力變矩器驅動鉆井泵可同時保護原動機和工作機；在保持柴油機額定轉速的條件下，可實現泵壓的全過程式控制制。
  17. Associated with a practical example of pipeline crossing with directional drilling technique in yizheng - changling crude oil pipeline, this paper analyzes the characteristics of crossing through rocky stratum with directional drilling, deliberates the stratum status, drilling machine selection, drilling tool assembly, direction control, mud control ; drilling process as well as emergency dealing scenarios at the stages of guiding - hole drilling, aperture expanding and back - towing

    摘要結合儀征長嶺原油管道洪湖長江定向鉆穿越工程實例，分析了管道定向鉆穿越長距離巖石層的特點，論述了定向鉆穿越巖石層的地層狀況、鉆具組合、控向措施、泥漿控制、鉆進工藝以及導向孔鉆進、擴孔、回拖階段的應急預案，針對在鉆導向孔過程中因泥漿壓力高、信號線多次出現被高壓泥漿沖壞、造成控向信號不穩定甚至中斷的情況，對信號線的安裝提出了改進措施。
  18. On the basis of analyzing the rock mechanics, the bit working circumstance and property in the bottom hole of 6000m deep well, and making use of the former equipment such as a derrick, platforms etc, the paper demonstrates that the research and design of the mechanical device have been established including the high pressure simulating well bore, the high pressure connector between the static well bore and the rotating drill pipe, the high pressure simulating system of circulating fluid and the high pressure desander etc. the produce, control and dynamic analysis of the bottom hole four - dimensional pressure ( over burden, confined, pore and column pressure ) have been studied

    本文在對井底巖石的受力狀態以及鉆頭的工作環境和特性加以分析的基礎上，藉助原有的井架、平臺等設備，研究設計了模擬6000米井底壓力壞境的高壓模擬井筒、鉆柱高壓轉聯器、鉆井液高壓模擬系統以及高壓除砂器等機械裝置，並研究了井底四維模擬壓力（上覆壓、圍壓、孔隙壓和液柱壓）的產生、控制及其控制的建模與模擬，從而實現井深至6000米的四維井底壓力環境的模擬。
  19. Tighten up fluid loss to give hthp fluid loss of < 15 with additions of drispac r / sl. before section td change to kemseal at 1 ~ 3 pounds per barrel

    用高粘或低粘錐斯派克控制失水，使高溫高壓失水小於15 。在鉆完本井段之前，改用每桶鉆井液加1 ~ 3磅的基母西爾。
  20. Since 1972, j series hammers and various rock drll bits have been developed, among them two products have won the prices of the national science conferences and fourteen products obtained scientific and technical achievement prices from the metaillurgy, ministry. all the products have been widely used in metal, coal, and industrial mineral mines, hydroelectrie construction sites and sold to the foreign markets as well. cimr machinery plant is a department responsible for trial - producing, manufacturing and marketing the research achievements of cimr, it has started manufacturing hammers and rock drill bits since 1958

    在與tanhoanganh公司主要代理建築和工程機械總經理nguyen huy huyen的交流過程中，當我們談到cs165智能整體型一體化液壓潛孔鉆機可鉆鑿100m深的孔，能把偏斜率控制在1 %以內，整個鑿巖過程在定位完成後自動完成，並配備了雙動力驅動系統時，他舉起大拇指，大呼「 powerful
分享友人
分享到 Line

分享到臉書