鉸外移 的英文怎麼說
中文拼音 [jiǎowàiyí]
鉸外移
英文
hinge offset-
After an introduction to the research on the software for the design of the variant steel arched girder construction, the creation of the structural model, the structure of the supporting seat, the design of the variant arched girder, and the measures taken to ensure the stability of the plane surface of the arched girder, the thesis goes to study the methods for the hoisting and the angle setting of the long - span arched girders, as well as the bolting of the axle pin in the hinge support
論文首先對變異鋼拱架結構設計可採用的軟體、結構模型的建立、支座構造形式、變異拱梁的設計，以及保證拱梁平面外穩定所採取的措施等進行了研究，然後研究了大跨度變異鋼拱架弧形梁吊裝、角度的調整、鉸支座穿軸銷等的施工方法，最後對施工完成後的位移進行了實際量測。Based on analysis of the iso - rigidity of the gyro assembly, the requirement for making the joints match each other is offered, which has a guiding significance for joints assembly and selection. based on analysis of rigidity and drift error for the dynamically tuned gyro, a cross model including an inner and an outer flexible hinges is established
在對動力調諧陀螺剛度和漂移誤差分析的基礎上，建立了由內外撓性接頭裝配所形成的十字型鉸鏈模型，並利用偽剛度理論對該模型進行了分析，得出了內外撓性接頭兩鉸鏈的相對位置關系對十字型鉸鏈模型的影響曲線。Then, this paper edits other computer program to calculate thirty sgrc frame columns, and researches the drift capacity of sgrc frame column, and analysis the turning capacity of frame column " s plastic hinge. then the relational expression of the curvature ductility factor and ratio of hoops of sgrc frame columns is derived. this paper analysis the relation of the curvature ductility factor and the relative drift of sgrc frame columns, and discuss the question of the minimum values of ratios of hoops of sgrc frame column at different axial load ratios
一11一太原理工大學碩_ i :學位論文使用本文程序另外模擬計算了30榻煤研石混凝土框架，進一步分析了軸壓比和配箍率對煤研石混凝土框架柱曲率延性的影響，編寫程序計算了30根煤研石混凝土框架柱，對煤研石混凝土框架柱的側向變形能力進行了研究，分析了柱塑性鉸的轉動能力，導出了煤研石混凝土框架柱的曲率延性系數與配箍率的關系式，分析了煤研石混凝土框架柱的曲率延性系數與框架柱相對側向位移的關系，討論了煤研石混凝土框架柱在不同軸壓比下最小配箍率的取值問題。On the basis of simplified calculation model presented by doctor wangxiaoping, some finite element models are set up. by finite element model program sap93, an analysis of static models of 18m - span and 30m - span w666 acmr in different supporting conditions is made. also a study on the relation between definite support displacement, which reflect variational stiffness of substructure represented by steel column or reinforced concrete column, and load - carrying capacity mechanical performance is made too
本文以w666金屬拱型波紋屋頂為研究對象，沿用王小平博士的簡化計算模型，對18m 、 30m跨波紋拱兩端不同支座形式（鉸支、固支和彈性支座）分別利用有限元計算程序sap93進行計算分析，研究波紋拱在不同跨度，不同支座形式下，不同外荷載作用時對該結構受力性能及穩定承載力的影響，同時分析下部支承鋼柱、鋼筋混凝土柱的剛度變化體現為允許支座位移的大小與結構受力性能及穩定承載力之間的關系。One of the methods to improve ductility of structure is controlling the plastic hinge position on beam effectively
改善鋼框架結構延性的做法之一是將塑性鉸的位置外移，從而提高結構抗震能力。分享友人