鉸接面 的英文怎麼說
中文拼音 [jiǎojiēmiàn]
鉸接面
英文
hinged surface-
From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints
採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。With the application of concrete - filled steel tubular member to mega - frame structures, the connection forms of main beam - column can be classified as welded rigid connection, bolted gemel connection and semi - rigid connection
摘要隨著鋼管混凝土組合截面日愈增多地應用於巨型框架中，主框架樑柱的連接形式分為焊接剛性連接、螺栓鉸接與半剛性連接。Sufficient or not of the battery on the device should be carefully examined before every flying, so do the every pole, helm and gemel, whether or not is the receiving antenna drew out of the body and in straight, examine the ground effective distance for remote control without the drawing out the antenna, ensure it nomal in rang of 30 - 50 meters
1 .仔細檢查測試設備每次飛行前都應該仔細檢查設備電量是否充足，檢查飛機各個拉桿舵角鉸鏈是否正常，接收機天線是否拉出機身並拉直，在不拉出發射機天線的情況下測試地面有效遙控距離，確定30 - 50米內不發生跳舵情況。A hinged or removable section for a table top
活動桌面桌子上部有鉸鏈連接或可移動的部分The evolution laws of structural weight, the best optimum fitness, average fitness, maximum nodal stress and displacement with increasing generations are discussed. and multi - result fact of the topology optimization can be obtained by ga - fem. the research results in this thesis show that the developed method is successful in the topology optimization for 2d continuum structures under multi - load and multi - constrain conditions
上述工作表明，本文ga ? fem可以實現多載荷、多約束條件下平面連續結構拓撲優化，與eso等優化方法獲得的優化結果相比，本文的優化結果不存在單元鉸接和不連續單元，優化結構多樣，質量更小，效果更優。In tins paper, a new type of standing - wave linear usm with square - ring vibrator was presented, which had two contact surfaces and a support structure with four flexure hinges for the power output
摘要利用有限元分析軟體對方環形直線駐波超聲波電動機的振子進行了動態設計，提出了一種環梁式雙接觸面的振子結構，該振子採用柔性鉸鏈與支撐結構連接，實現力的輸出。The main work includes : the kinematic properties of a planner 4 - bar linkage are researched deeply using the assur group theory. the displacement, velocity and acceleration of each joint point in a motion period are put forward and their curves of the relevant points are plotted
通過運動學分析，得出平面連桿機構在一個運動周期中各鉸接點的位置、速度和加速度以及各桿件的角速度、角加速度等運動學參數，並繪制出相應的變化曲線。Calculation of out - of - plane stability of bending members with box sections
兩端鉸接楔形壓彎桿平面外穩定Pseudo - static force testing of 1 : 2 scale models of a steel frame with dog - bone connections is first carried out in china in order to obtain elastic - plastic behavior of dog - bone connections steel frames under cyclic loading as well as to analyze collapse characteristic after structural ultimate strength has lost. the influence of dog - bone connection on the coming order of plastic hinges and failure characteristic of steel frame, and the influence of dog - bone ' s shape and position on the behavior of structure is obtained
通過試驗考察了狗骨式連接平面鋼框架結構在循環荷載作用下的彈塑性性能;了解狗骨式連接對結構塑性鉸出現的順序以及結構破壞形態的影響;了解節點處與狗骨處應力發展狀況，探討狗骨削弱的形狀和削弱位置對節點性能的影響。By calculating large quantity of examples, this text studies earthquake resistant behavior of tapered portal frame with pined bases and analyzes its natural frequency, natural period of vibration and vibration mode. by comparing interior forces of pillar top, beam end and span midpoint in two conditions that seismic action effect participates combination of forces and not when portal frame is n ' t changed, ensure conditions that combination of seismic action effect has controlling f unction during tapered portal frame design, and tapered portal frame demands anti - earthquake design
本文通過大量算例分析，研究柱腳鉸接楔形變截面門式剛架的抗震性能，並對其自振頻率、振型進行了分析；通過比較地震作用效應參與荷載組合與不參與荷載組合兩種情況下，樑柱截面尺寸不變時，柱上端、梁端、跨中截面處的內力大小，確定在什麼情況下地震作用效應組合起控製作用，變截面門式剛架需要進行抗震設計。Dalian kerui economics trade co., ltd. sell tapes for bonding in industry, reclosable fasteners, adhesives, polish and grind material, anti - electrostatic and insulation tape america 3m company, heat shrinkable tubing, wire and cable, electrical thermal wire and system america raychem company, masterbatch hanna - wilson, silicone products ge toshiba company and electrostatic electronic hydrotreater, water tank self - cleaning sterilizer beijing enfi company
公司經銷美國3m各種工業用單雙面膠帶尼搭扣粘接劑拋光研磨材料防靜電材料絕緣膠帶美國瑞侃公司單雙層熱縮管鉸鏈薄壁耐高溫導線電伴熱線及系統漢納威爾遜色母料ge東芝有機硅產品和各種靜電水處理器水箱自潔消毒器。Orthopaedic joint prostheses - components for partial and total knee - joint prostheses - articulating surfaces made of metal, ceramic and plastics materials
矯形外科關節假體.部分和整體膝關節假體部件.由金屬陶瓷和塑料材料製成的鉸接表面The main shuchural features of the new electric single - girder overhead travelling crane presented in this paper is as follows : using a special gisder section to provide simple production technology and light weight ; dopting hinged connection at one end between main glrders and end carrages instead of the rigid connection at both ends, eliminating the three - point supporting problem with the crane and thus improving the travelling perfomance ; extending crane wheels life contributed to the combination of no - flange crane wheels and horizontal rollers
提供種生產工藝簡單、自重輕的主梁截面，並將單梁起重機主、端梁的剛性連接改為端用鉸接連接，解決了在製造和軌道安裝時因誤差而造成的大車運行三條腿現象，提高了運行性能；用可調大車運行水平輪中心距的設計，代替帶輪緣的大車輪，提高大車輪的使用壽命。The rear door hinges / is hinged at the top so that it opens upwards
後面的門是在頂部鉸接上的，以便可以向上開In allusion to section modality and transverse joint of common span bridges, we choose two kinds of calculating theories in transverse distributing calculate process : the theory of rigidity crossbeam and the theory of hinged girder and slab. making the use of the theory of optimized design, i constitute mathematics model and choose appropriate calculated method. and find the form and detail dimension of section when beams of the bridge satisfy bending moment ^ shearing force and torsional moment
在用橫向分佈理論計算單梁扭矩過程中，針對現有常用跨徑橋梁的截面形式和橫向連接狀況，選取了兩種計算理論：剛性橫梁法和鉸接梁（板）法，利用結構優化設計原理，建立主梁承載力的數學模型，選擇合適的優化計算方法，得出在滿足彎剪扭承載力要求時主梁的細部尺寸。To completely avoid producing elements jointed at their corner nodes and checkerboard patterns, which frequently occur when the topology optimization of plane continuum is studied, the theory of topology analysis of plane continuum in topology optimization process and the simple algorithm for programming are studied. according to algebraic topology theory, the boundary of elements and plane continuum are operated as a one - dimensional complex. by use of the adjacency vector in graph theory, the structural topology is described and the topological operation is achieved on a computer. by above, the structural topological feature in the evolutionary process is gained. these methods are effcient and reliable. under topology constraints, according to the results of stress analysis, by deleting elements and moving nodes at the boundary, more satisfactory results can be gained by using a few numbers of elements and iterations. to demonstrate the efficiency of these methods, solutions including some well - known classical problems are presented
避免目前平面連續體結構拓撲優化過程中經常出現的單元鉸接以及「棋盤格」等現象，研究了連續體結構拓撲優化過程的拓撲分析方法，以及在計算機上實現的簡便演算法.根據代數拓撲理論，單元及連續體的邊界作為1 -復形進行運算.利用圖論中的鄰接向量概念，在計算機上實現了結構的拓撲描述及拓撲運算，得到了結構在拓撲演化過程中的拓撲特性，方法簡單、可靠.在一定的拓撲約束下，根據應力分析結果，採用刪除單元、單元退化、移動節點等方法，可以用較少單元得到更為滿意的結果，提高計算效率.為演示方法的有效性，給出幾個包括常見經典問題的解答Contrasting with the sliding vane compressor and the rolling piston type rotary compressor, the character of the new structure and its working principle are introduced in detail. the facts that affect its working process have been analyzed. the kinetic process of the sliding vane and rotary cylinder are studied
文中通過對比轉缸鉸接滑片壓縮機與滑片壓縮機、滾動轉子壓縮機的在結構及工作過程上的相同與不同之處，詳細介紹了這種壓縮機結構方面的特點和工作原理，並分析了影響這種轉缸鉸接滑片壓縮機工作過程的各種因素。In this paper, slender columns with the two ends hinged are considered. an iterative computer analysis procedure taking into account the second - order effect of the axial load is proposed to predict this complete load - deformation process
本文針對兩端鉸接的任意截面鋼-砼組合長柱，考慮長柱在偏心荷載作用下的附加彎矩影響（二階效應） ，提出了一種數值迭代的計算機方法進行全過程分析。In order to study basic roof ' s destruction movement that affects working face in horizontal section top coal caving in mining steep seams, this paper analyses tension of roof using elastic and thin board theory and concludes criterion of roof destruction based on long and narrow thin board
摘要為研究急斜煤層水平分段放頂煤開采過程中基本頂破壞活動對工作面的影響，根據急斜煤層基本頂具有傾斜狹長板的特點，運用彈性薄板理論對基本頂巖層進行了拉應力分析，得出了頂板破斷的判別準則，建立了基本頂初次破斷后形成的「鉸接結構」的力學模型。In order to study the basic roof ' s destruction movement that affects working face in horizontal section top coal caving in mining steep seams, this paper analyses tension of roof using elastic and thin board theory and obtains criterion of roof destruction based on long and narrow thin board
摘要為研究急斜煤層水平分段放頂煤開采過程中基本頂破壞活動對工作面的影響，根據急斜煤層基本頂具有傾斜狹長板的特點，運用彈性薄板理論對基本頂巖層進行了拉應力分析，得出了頂板破斷的判別準則，建立了基本頂初次破斷后形成的「鉸接結構」的力學模型。分享友人