銅焊連接 的英文怎麼說
中文拼音 [tónghànliánjiē]
銅焊連接
英文
copper bond- 銅 : 名詞(金屬元素) copper (cu)
- 焊 : 動詞(用熔化的金屬修補金屬器物或使金屬工件連接起來) weld; solder
- 連 : Ⅰ動詞1 (連接) link; join; connect 2 (連累) involve (in trouble); implicate 3 [方言] (縫) ...
- 接 : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
- 連接 : connect; fit together; link; marry; mate; joint; association trail; linkage; concatenate; concate...
-
Assemblies incorporating a wire terminal of neon or fluorescent lamp with series resistor, if required, extended single conductor lead wires can be produced with butt welded, crimped or tin soldered joints
氖燈電阻熒光燈氖燈與電阻的連接可分為:碰焊打銅扣以及錫焊。Cast copper alloy solder joint drainage fittings - dwv
Dwv鑄銅合金釬焊連接排水配件Cast copper alloy solder joint drainage fittings : dwv
Dwv類鑄銅合金釬焊連接排水管件Cast copper alloy solder joint pressure fittings
鑄銅合金軟釬焊連接壓力管件Wrought copper and copper alloy solder - joint pressure fittings
鍛銅和銅合金釬焊接壓力連接件Cast copper alloy solder joint drainage fittings - dwv ; errata
鑄銅合金軟釬焊連接排水管件. dwv .勘誤Heat solder joints only to the point were solder will flow properly. excessive heat may distort brass castings
熱焊料連接只能用在焊料能夠正確流動的地方。過熱可能扭曲黃銅鑄件。Rated internal pressure is that of the tube being joined. while solders can be used, brazing alloys are recommended
額定內部壓力是所連接的管道額定內部壓力。如果可以採用焊料,則推薦使用銅焊合金。H rated internal pressure is that of the tube being joined. while solders can be used, brazing alloys are recommended
額定內部壓力是所連接的管道額定內部壓力。如果可以採用焊料,則推薦使用銅焊合金。A new type of joint technique between short _ net copper pipe and soft _ cable connection board, castfusion welding, is introduced. the practice of more than ten years shows that this fusion welding connection has the superiority of higher reliability, simpler processing method, better economy benefit compared to the taper cone face - contacted connection
介紹了電石爐短網銅管與軟纜接線板之間的一種新型連接技術? ?澆鑄熔焊技術.經過10多年的運行,實踐證明短網銅管與鑄銅軟纜接線板的澆鑄熔焊連接,與傳統工藝採用的圓錐面接觸連接相比較,具有加工工藝簡單、運行可靠性高、經濟效益好等優點Connectors, electrical, circular, coupled by threaded ring, fire - resistant or non fire - resistant, operating temperatures 175 c continuous, 200 c continuous, 260 c peak - hermetic receptacle with round flange attached by soldering or brazing - product standard
連續工作溫度為175 200極端溫度為260時耐火或不耐火的由螺紋環連接的環形電連接器.軟焊或銅焊上圓頭法蘭密封插座.產品標準Standard for safety for wire connectors and soldering lugs for use with copper conductors
與銅導線一起使用的電線連接器和焊片的安全性標準Keep flame away from rod or wire at it is fed into the joint
在銅焊線(條)進入連接部位時,不要讓火焰接觸到銅焊線(條) 。Section four plugs, the outer covering plastic completely uses anti - burns the abs material quality, the standard gb code three plugs ; 0. 75squares line diameter 3 meters power lines dispositions, the entirecopper tape interior connection, ceases the traditional way whichformerly welded to cause, switch sideinstallment, convenient customer use ; the multi - purpose plug holedesign, may meet inserts the world 32 countries standard plugs
一款四位插座,外殼塑料全部採用阻燃abs材質,標準國標三眼插頭; 0 . 75平方線徑3米電源線配置,全銅帶內部連接,杜絕以往焊接的傳統方式導致虛焊或脫焊;船型開關側面安裝,方便客戶使用;萬能插座孔設計,可接插世界32個國家標準插頭。Friction stir welding ( fsw ) is a solid - phase welding operated under the melting point of workpiece materials ; it ' s a technology which uses an anti - friction tool to join the sheet or shaped materials in rotary circs, and can be used in the welding of aluminum, magnesium and copper and has good welding quality
摘要摩擦攪拌焊( fsw )是在低於工件材料熔點情況下操作的固相焊接,是在旋轉情況下通過一種耐磨工具將板材或型材材料連接的工藝,可用於鋁、鎂、銅等的焊接,焊接質量優良。Study on the friction welding and whole sintering between copper and w80cu20 materials
鎢銅材料與銅的摩擦焊連接研究Manufacturing processes joining - part 7 : joining by soldering or brazing ; classification, subdivision, terms and definitions
連接加工工藝.第7部分:釬焊或銅焊連接.分類細分類The strength of a brazed joint does not vary appreciably with the different brazing materials, but depends to a large extent upon the maintenance of proper clearance between the outside of the tube and the valve socket
銅焊連接的強度並不會因為採用不同的銅焊材料而又多大的變化,但是卻與管道外側和閥門插口之間的清理是否正確有很大的關系。Welded, brazed and soldered joints - symbolic representation on drawings
焊接銅焊和軟釬焊連接件.制圖符號標注Commercial building telecommunications cabling standard - part 2 : balanced twisted pair cabling components - addendum 4 - solderless connection reliability requirements for copper connecting hardware
商用建築電信電纜敷設標準.第2部分:對稱雙絞合線電纜敷設.補充件4 .銅制連接硬體的無釬焊連接的可靠性要求分享友人