鋸齒模 的英文怎麼說
中文拼音 [jūchǐmó]
鋸齒模
英文
zigzag mode-
Let's consider the sawtooth pattern of similar triangles in fig. 9.
我們來研究圖9中一組相似三角形的鋸齒形模型。The sawtooth model applies more widely
這種鋸齒模型可以用到更廣泛的領域。Before us was a mighty chasm in the black rock, jagged, torn, and splintered through it in a far past age by some awful convulsion of nature.
我們前面是一道黑黝黝的巨大的深淵，大約很久很久以前一次可怕的大震動將它崩裂撕扯成這種鋸齒獠牙般模樣。Synchronized drive module produces horizontal drive signal in synchronization with horizontal synchronization signal and field drive sawtooth in synchronization with vertical synchronization signal. these signal drive scaning sytem of slltv
同步驅動模塊產生與行、場同步的行同步驅動信號和場鋸齒波驅動信號，用於驅動激光電視的掃描系統。Abstract : this paper is mainly about an analog saw - tooth signal generator used for linear histogram test of adcs
摘要：主要內容是基於線性直方圖法測量模?數轉換器性能的片上模擬鋸齒波發生器的實現方法。Sealing and sliding sealing rings, cutting tools, reamer tips, reamer heads, saw tips, clamping supports, inserts for bore - crowns, plates, tip inserts for measuring and testing devices, nozzles, lining bushings, milling inserts, cold rolls, drawing dies, powder pressing dies
密封環和滑動密封環、切削工具、絞刀齒、絞刀頭、鋸齒、夾具、牙冠填充物、金屬板、測量和試驗儀器的頂端襯墊、噴嘴、襯套軸套、銑削襯墊、冷壓模具、沖模、粉末壓模。In the meantime, the all sub - circuits are also designed and emulated carefully including inverter, rs type flip - flop, voltage reference circuit, error amplifier, voltage comparator, sawtooth - wave generator, pwm comparator, soft activation circuit and so on. as a result, all of the sub - circuits answer the requirements. this chip has taped out with the 0. 5um mix - signal process of csmc
本文利用cadenceeda集成電路設計工具、 spectres模擬工具，對集成電路內的各個模塊包括反相器、基本rs觸發器、基準電壓電路、誤差放大電路、電壓比較電路、鋸齒波振蕩發生電路、 pwm比較電路、軟啟動電路、驅動電路等進行了具體的設計和模擬，且達到了預先設定的指標。Passive suspension, pid control semi - active suspension and neural network control semi - active suspension are researched by simulation. white noise, sine wave and sawtooth wave are used for excitation. the root mean square value of vehicle body acceleration, suspension displacement and vehicle wheel load are analyzed
在模擬研究中，路面激勵取為白噪聲、正弦波和鋸齒波，懸架類型採用被動懸架、 pid控制半主動懸架、神經網路控制半主動懸架三種。When the applied bias voltage is changed within positive slope regions of u - i curve, the domain boundary between the high and low electric field domains does not moved, and the size of electric field domains regions is also not altered, while the electric field strengths are adjusted
用模擬計算的方法研究了弱耦合摻雜gaaa / alas超晶格在時變電壓下的場疇機制和固定偏壓下電流自維持振蕩。在時變電壓下，一定摻雜的超晶格處于穩定的電場疇， u - i曲線呈現鋸齒狀波形。Anti - aliasing, capability of the rasterizer to simulate unfitted pixels with some illusion to human perception, such as using grayscales and coloured - subpixels, resulting in the feeling of " smooth curves.
反鋸齒：點陣化時用人眼錯覺來模擬未擬合的像素的技術，例如用灰度和各種顏色的次像素讓人產生「平滑曲線」的感覺。And relying on this, our laboratory proposes a new cladding method. by means of large dynamic explicit fem code ansys / ls - dyna, the numerical simulation was carried out in bimetal forming process. during the simulation of the forming process, the large deformation of the strip should be considered, as well as geometrical and material nonlinear, the contact between the roller and the strip, the contact between two metal sheets and the load. as for these problems, we can use node to surface contact and relative parameters, biso model is introduced, the load is applied as array
本文採用ansys / ls - dyna計算程序為分析工具，對鋸齒形雙金屬復合板成型過程進行計算機數值模擬，在對軋制過程模擬時，針對軋件變形的幾何非線性和材料非線性特點、軋輥與軋件間的接觸、軋件間的接觸以及模型的加載等問題，給出了在ansys / ls - dyna中相應的解決方法：應用nodetosurface接觸方式，設定相應參數，選用雙線性等向硬化模型，載荷作為array施加在剛體質心。G70x, handles antialiasing, post process, motion blur
則處理抗鋸齒，影像後期處理，運動模糊。The results indicate that the time of press influences sawtooth distortion greatly, but infects sawtooth less. root of the sawtooth made by the method of static simulating rolling have no changes hardly, and from the upper distance the changes became, then on the top the sawtooth curves to the opposite direction
結果表明：壓制時間對齒形的變形影響較大，對齒型的影響很小；模擬軋輥壓制的鋸齒，根部一段幾乎沒有變化，是從一段距離開始變形，然後在頂端向相反的方向彎曲；壓製成型后，鋁板厚度的變化很小。分享友人