鋼板承載試驗 的英文怎麼說

中文拼音 [gāngbǎnchéngzǎishìyàn]
鋼板承載試驗 英文
plate bearing test
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 鋼板 : [冶金學]1 （板狀鋼材） steel plate; nickelclad steel sheet; plate 2 （汽車上的片狀彈簧） spring3 ...
  • 試驗 : trial; experiment; test
  1. Based on tests of nine 1 / 2 - scaled model slabs under vertical loads, the paper analyzed load - deformation curve and proposed limit value of height - width ratio under axial loads. 2. based on aseismic tests, the paper put forward a model of concrete frame, silica brick and a combination of the two, proposed that the silica brick works as a 45 compression bar, analyzed the factors which may influence bearing capacity of the slab and advised a formula including the numbers of bays and of storeys of the frame

    通過對墻板模型的抗震性能試驗研究，建立了由鋼筋混凝土框格、砌塊以及兩者協同作用三個部分組成的承載力極限狀態下的理論簡化計算模型；提出了墻板中填充塊等效斜壓桿寬度按45度計算的統一量化標準；分析了影響墻板承載力的主要影響因素，給出了表達墻板框格層數和跨數不同的斜截面承載力實用設計計算公式。
  2. Abstract : experimental researches on normal section ultimate fle xural strength of prestressed reverse - rib - slab with excessive steel bar were m ade, and according to chinese norm ( gbj10 - 89 ) and american norm ( aci ) in which s train harmony analysis method was adopted, its ultimate strength was calculated, these make us further realizse the ultimate flexural strength of prestressed r everse - rib - slab with excessive steel bar

    文摘:通過疊合結構中預應力超筋倒肋薄板正截面極限承載力的試驗研究，分別採用規范gbj10 - 89中的受彎構件、偏心受壓構件的計算公式及美國aci規范中的應變協調分析方法計算了極限承載力，從而更清楚地認識了配有高強鋼絲的超筋倒肋板的極限承載力計算問題。
  3. The results of full - scale tests in this dissertation canaugment international database of test and numerical analysis results for tubularjoints. based on the experimental study and numerical analysis, design proposal for theultimate tensile strength of gusset plate connections to slotted tubes is recommended. it has bigness significance to establish design formulae of gusset plate connections toslotted tubes and perfect design formulae of steel tension member and it also can givesome advices to practice engineering

    在試驗研究的基礎上，根據有限元分析的結果，本文提出了關于管板節點受拉極限承載力的設計公式，為我國鋼結構規范建立管板節點受拉極限承載力設計公式及有關拉桿的設計公式的進一步完善提供了有意義的參考，同時對實際工程也有一定的參考價值。
  4. This research was also supposed to provide a valuable reference for the construction of 500kv eastern hangzhou transformer substation project. to guarantee the rationality of the torsion and bending load application, a set of experimental equipments was transformed from a traditional one by exerting tangential force on the brim of the fan board and conducting broad - billed roller application. in the actually fulfilled experiments on the capabilities of the members under different ratios of torsion and bending, the equipments proved to be well qualified in load applying to large - tonnage members

    試驗中，為保證扭轉及彎矩荷載施加的合理性，在浙江大學工程結構試驗室原有的加載設備的基礎上，分別採用在扇形板邊緣施加切向力和寬軸承滾軸加載的方法，改造並調試出一套可專門用於大噸位構件施加扭轉荷載及組合作用的試驗設備，並利用這套設備進行了離心鋼管混凝土構件在不同彎扭比的組合作用下的試驗研究。
  5. In this thesis, the new structure of pre - stressed cantilever composite beam with corrugated steel webs on steel - concrete composite spine girder was brought forward for the first time, a series of experimental researches and theoretical analyses relating to this new structure are conducted, including load transverse distribution rule, shrinkage and creep effect, temperature difference effect, and ultimate bearing capacity

    本文提出大懸臂預應力波形鋼腹板挑梁這一新的構造形式，對其橫向分佈規律、收縮徐變、溫差效應以及承載能力等方面的受力特徵進行了分析和試驗研究。
  6. For the cantilever beam, the theoretical stiffness and limited capacity are slightly less than the test ones if considering only the steel beam and the reinforced bars in the negative moment zone with the concrete in the tension zone ignored

    結果表明：簡支組合扁梁，忽略彈性中和軸以下受拉的混凝土的影響，採用等效換算截面方法計算所得的剛度和極限承載力與試驗結果比較吻合；懸臂梁只考慮混凝土板中配置的負彎矩鋼筋，忽略混凝土，計算所得的剛度和極限承載力比試驗結果略微偏小，但相差不大。
  7. The experimental result indicate that the working characters of the test floor slab is typically two - way obviously, the floor slab that is reinforced two - way by setting transverse steels through the rectangular cores in the ribs of the precast slabs, has excellent bulking property, high bearing capacity, cracking resistance and so on

    試驗研究表明，試驗樓蓋在加載過程中呈現了明顯的雙向受力特徵; pk預應力疊合樓蓋通過在預制構件板肋預留長方形孔穿置橫向鋼筋實現雙向配筋具有良好的整體性能，還具備承載力高和抗裂性能良好等特點。
  8. Through comparing and analyzing of bearing capacity, development of crack and strain of reinforced, the results show that the load - deflection plots f or specimens from the finite element analysis agree well with the experimental data, and choosing the rightful stress - strain relationship, utilizing ansys program, the test process can be well simulated. at the same time, making used of the program, the traditional shear wall is analyzed. it shows that comparing with the traditional shear wall, the hollow shear wall ' s cracking load drop 16 %, yield load and failure load drop 13 %, stiffness drop 13 % ~ 22 %

    其次在試驗的基礎上，將試驗手段、有限元數值模擬方法和理論分析結合起來，利用有限元程序ansys對其中的兩片墻板進行非線性有限元分析，並對前後的承載性能，裂縫發展、鋼筋應變進行了比較和分析，結果表明有限元節點模型分析的荷載-位移曲線和試驗測得數據符合良好，選用合理的材料本構模型，利用ansys可以較好的模擬試驗過程；同時利用有限元模型對比分析了普通剪力墻和空心剪力墻，空心剪力墻與普通剪力墻對比，其開裂荷載下降16 ，屈服荷載、極限荷載下降13 ，剛度下降13 22 ，開裂至屈服、屈服至極限荷載階段的剛度衰減規律與普通剪力墻基本一致，空心剪力墻的後期剛度比較穩定。
  9. The paper made up a flexural experiment with six pieces of composite slab. during the every step of load exerted, the paper recorded the strain of cold - form steel deck and concrete, deflection, crack, slide, ultimate bearing capacity. by changing the thickness of cold - form deck, thickness and strength of concrete, amount of steel stud and other parameters, the paper discussed the behavior of loaded composite - slab

    本文進行6塊組合板的抗彎性能試驗，測試各級荷載下壓型鋼板及砼應變、組合板撓度、裂縫、板端滑移、組合板抗彎極限承載力；通過壓型鋼板厚度、砼板厚度、砼強度等級、栓釘數量等幾個參數的變化，探討組合板在荷載作用下的內力、變形情況。
  10. Secondly, by low - cycle and reverse horizontal loading test, their properties including strength property, deformation property and energy property are studied. we study the loading characteristic values ; the property of hysteretic curve and skeleton - frame curves ; the ductility property and stiffness degradation. at last we analyze the destroy principle and affection reasons of hollow shear wall of r. c with vertical seams in different height and loading measures, we also give the bearing capability calculation formulas and design advises for new type hollow shear wall of r. c

    首先運用ansys有限元程序分析彈性階段水平外荷載施加后，帶豎縫鋼筋砼空心剪力墻板內應力分佈及變形情況，再在試驗數據的基礎上，研究低周反復水平加載條件下，各試件的強度、變形、能量特性；各試件的荷載特徵值；各試件的滯回曲線、骨架曲線；延性及剛度退化等參數；最後，分析了不同剪跨比和加載條件的帶豎縫鋼筋砼空心剪力墻板的破壞機理和承載力影響因素，並給出不同剪跨比和加載條件的帶豎縫鋼筋砼空心剪力墻板承載力計算公式及設計建議。
  11. On the basis of the traditional elasticity theory, nonlinear theory, ultimate theory and theory of reinforced concrete slabs with simple - supported condition, this paper analyzes the whole process of reinforced concrete thin slabs in the loading test of distributing static load, on the objects of reinforced concrete thin slabs with complex geometry, complex boundary condition and distributing of reinforce bars. and then analyzes the load capacity under the effecting of static load

    本文在傳統的鋼筋混凝土彈性理論、非線性理論和極限理論以及在簡單支承條件下的鋼筋混凝土板理論的基礎上，以復雜幾何形狀、邊界條件及配筋形式的鋼筋混凝土薄板為研究對象，對其在靜力分配梁加載下的加荷試驗的全過程進行分析，並對其在靜荷作用下的受力性能進行分析。
  12. Experimental results show that the new cfrt - column to steel - beam joints proposed in this paper possess good earthquake resistant capacity. the infilled concrete benefit to restrain the buckling deformation of column webs, increase the strength and stiffness of the joint. the lengthened stiffener can transfer much more beam moment, make the strength of the joint increased

    試驗表明，在保證焊接質量的前提下，本文提出的新型方鋼管混凝土柱?鋼梁的節點具有良好的抗震性能；內填混凝土有利於抑制柱腹板的屈曲變形，增加節點的承載力和剛度；加勁肋長度的增加有利於傳遞梁端彎矩，使節點的承載力提高。
  13. In this thesis, a series of single and double - direction - load tests are carried on the single plate framing connection between truss - steel beam and concrete wall often used in tall - building. by single - direction - load tests, the flexure capacity of the joints in use of different design is researched in particular, the effect of bolt design on the flexure capability is analysised ; based on the cyclic loading experiment, such characteristics of the anchors are analyzed -. bearing capacity. rigidity, ductility, hystersity capacity, energy dissipation and failure phenomena

    通過單向靜力試驗，研究了單剪板連接的不同設計對鋼架梁的約束能力的變化，重點討論了螺栓的設計對約束能力的影響；通過周期性反復加載試驗研究了不同設計的單剪板連接預埋件的抗震性能的不同，重點分析了結構的承載能力、剛度、延性、滯回性能、耗能能力及其破壞特徵等。
  14. The main contents of the research : the material ' s property in reinforced concrete structure with corroding reinforcement and an experimental study on concrete roof plate ' s bearing capacity with corroding reinforcement and later into rating concrete

    本課題主要研究內容是：鋼筋混凝土結構鋼筋銹蝕后材料性能研究；鋼筋銹蝕和混凝土破損屋面板承載力試驗研究。
  15. Initial rotational stiffness ri and ultimate moment capacity mu of top - and seat - angle steel connections is given in this text. initial rotational stiffness rt and ultimate moment capacity mu of top - and seat - angle with double web - angle steel connections is given in this text. it is right by comparison with experiment

    推導了頂底角鋼、腹板雙角鋼連接的初始連接剛度r _ i ，頂底角鋼、腹板雙角鋼連接的極限彎矩承載力並經和試驗比較得出兩種連接型式的初始連接剛度、極限彎距承載力其理論值和試驗值的相對誤差在工程允許的范圍內。
分享友人
分享到 Line

分享到臉書