鋼梁 的英文怎麼說

中文拼音 [gāngliáng]
鋼梁 英文
girder steel; steel girder
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 梁 : 名詞1 （屋架中架在柱子上的長木） beam 2 （通常也指檁） purlin 3 （橋） bridge4 （物體中間條狀隆起...
  1. Elastic theory and plastic theory are adopted in the analysis of the two section composite beam. elastic theory suggests, on the condition of the same steel beam section size, the composite beam for the floorslab is suited lower flanges convertion section stiffness cuts down by 75. 1 %, elastic limit bending resistant capability cuts down by 47. 9 %, than the composite beam for the floorslab is suited on the top flange. it s conversion section stiffness is lifted 8. 0 %, elastic limit bending resistant capability is lifted 0. 20 %, than the steel beam

    彈性理論分析的結果表明，在鋼梁截面大小相同的條件下，樓板位於鋼梁下翼緣的組合梁和樓板位於鋼樑上翼緣的組合梁相比，其換算截面剛度降低75 . 1 ，梁的彈性極限抗彎承載力降低47 . 9 ，樓板位於鋼梁下翼緣的組合梁和純鋼梁相比，其換算截面剛度提高8 . 0 ，梁的彈性極限抗彎承載力提高0 . 2 。
  2. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  3. Inquiring into coal extraction by caving face with steel beam in extraordinary geologic zone

    型鋼梁放頂煤工作面在特殊地質構造區域採煤的探索
  4. Colligation point of girder should ensure stability of assembly, otherwise, temporary fixation should be carried out before assembly

    鋼梁的綁扎點要保證鋼梁的吊裝穩定性，否則就需在吊裝前進行臨時加固。
  5. Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior

    分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大，實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著，而連接端板厚度及剪力連接程度的影響則不是太顯著。
  6. During calculation of the ultimate flexural capacity of composite beams, it assumes steel beam, concrete board and connecter are plastic, calculates them by ultimate equilibrium method

    在組合梁受彎極限承載力計算中，認為鋼梁、混凝土板和連接件完全塑性，採用極限平衡法計算。
  7. Methods of test for falsework equipment - floor centres

    腳手架設備試驗方法.第1部分:可調鋼梁
  8. Transfer matrix method of internal force analysisof tapered h - section steel beam

    型鋼梁內力分析的傳遞矩陣法
  9. Analysis on the elastic stability of elastic restraints for h - section steel beams

    型截面鋼梁的彈性穩定性分析
  10. Wp = 6 > the practical table is compiled that integral stability coefficient of homemade rolled h - section steel beam under constant moment

    編制了等端彎矩作用下軋制h型鋼梁式構件的整體穩定系數表，可供工程設計參考。
  11. The suggestion is put forward that adopting the different geometry control condition between rolled h - section steel beam and general i - section steel beam

    本文提出軋制h型鋼的幾何控制條件，並建議將一般工字形截面簡支梁和軋制h型鋼梁分列處理。
  12. One steel producer, the xin yu iron and steel group in jiangxi province, operates a production complex including wire rod mills, a beam - rolling mill and plate - rolling mills

    其中的一家生產商，江西新余鋼鐵集團，主要生產包括盤條鋼、鋼梁軋鋼以及中厚板鋼等。
  13. In this study, sts - - the steel construction design module of pkpm, a software program of china " s institute of the construction science - - is employed to create the construction model in order to study the construction of the supporting seat. a mechanical analysis of the variant arched girders was implemented, with the result that consturction documents meeting mechanical requirements were designed for the hinge support, the roller support and the steel girders

    本文採用中國建築科學研究院pkpm軟體的鋼結構設計模塊sts ，從結構建模入手，根據規范要求研究了支座的構造形式，通過對變異拱梁的力學分析，設計出符合力學模型的鉸支座、滑移支座和變異拱處鋼梁的施工圖。
  14. The main body of the stadium is composed of 24 columns of trusses, which surround the bowl - shaped stands in the stadium

    鋼結構由24桁架柱圍繞著體育場碗狀看臺區旋轉而成，整體外觀酷似「鳥巢」造型。構架，桁架，鋼梁
  15. With the actual locale incestigating, the actual locale testing and the theories analyzing of the reason of the diseases producing of the exceed limit of horizontal swing and steel pole ' s break, and summaried the reinforcing measure of the top bear armor plate beam

    通過對京廣線鄭州黃河大橋40米上承式鋼板梁橫向擺動嚴重超限及鋼梁桿件斷裂等情況的現場調查、現場測試和理論分析及病害原因產生的機理，總結提出了上承式鋼板梁的加固措施。
  16. Major products of the company are : ventilation equipments, including various types of fans, inlets, cool cells, and accessories ; livestock flooring systems including plastic floors, cast iron floors, high tensile steel beam, fiberglass beams etc, the company also produces patented full system containerized nursery buildings. consumer products such as hand tools and hardware, lighting

    公司主要產品包括:通風設備，含多種風扇、風口、水簾系統及配件；養殖設備含塑料地板、鑄鐵地板、高強度鋼梁、玻璃鋼梁等；公司還生產專利產品移動式集裝箱豬舍；消費品，如手動工具、五金工具、燈具等。
  17. Plastic theory suggests, the composite beam for the floorslab is suited lower flange, it s plastic limit moment cuts down by 52. 4 % than the composite beam for the floorslab is suited on the top flange. it s plastic limit moment lifts 8. 8 % than the steel beam, which is on the same condition

    塑性理論分析的結果表明，樓板位於鋼梁下翼緣形式的組合梁和樓板位於鋼樑上翼緣形式的組合梁截面相比較，其塑性極限彎矩降低52 . 4 ，和同等條件下純鋼梁截面相比較，樓板位於鋼梁下翼緣的組合梁塑性極限彎矩提高8 . 8 。
  18. Thus it is necessary to study moment resistance, rotation stiffness and rotation capacity of the joints. in this paper, six specimens on end - plate composite beam - to - column joints and two specimens on end - plate composite beam - to - column joints were designed to subject to static load. the factors of m - characteristics about semi - rigid composite joints, including bolts, profiled steel sheeting, beam, column, stiffen rib and reinforcement, are studied

    本文設計了6個端板型鋼-混凝土組合樑柱節點與2個端板型純鋼樑柱節點，通過對這些試件的靜力荷載試驗，重點研究了端板型鋼-混凝土組合節點的彎矩-轉角性能的影響因素，包括高強螺栓、壓型鋼板、型鋼梁、型鋼柱、加勁肋，以及混凝土板內縱向鋼筋配筋率等。
  19. It was essential that the lifted girder could be moved by any angle. a hand drawn chain hoist was used instead of a steel wire rope to enable the girder to be moved freelyby any angle. the suspension centers should be kept far apart but to the front as much as possible

    起吊后的鋼梁靈活、方便的角度調整是關鍵，吊裝時用有足夠行程的手拉葫蘆代替鋼絲繩，以便進行角度調整，要求吊點相距要大一些，而且吊點盡量靠前端。
  20. Necessary pressure tubes and steel beams may be either incorporated in the block or added later, depending on the design.

    按設計要求，必要的壓力導管和鋼梁可以與成形件做在一起，也可以以後再加。
分享友人
分享到 Line

分享到臉書