鋼液面控制 的英文怎麼說

中文拼音 [gāngyèmiànkòngzhì]
鋼液面控制 英文
liquid steel level control
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 液 : 名詞（液體） liquid; fluid; juice
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. Is the mould level and flow control in a closed loop system and are abrupt changes alerted, monitored and affected blooms controlled / downgraded

    鑄模液面高度和（鋼水）流控制是否在封閉的循環系統中進行？對突發情況是否有報警，監控措施？並且對受影響的鋼坯得到控制和降級使用？
  2. Abstract : with pc - controlled liquid drop counter, protective atmospher es of ball annealing of wires is strictly kept. pickling is easily gained in proc ess of ball annealing of wires and quality wires are produced

    文摘:採用電腦液體滴速計數儀，嚴格控制針布齒條用規格鋼絲球化退火的保護氣氛，防止和消滅針布齒條在球化退火過程中出現的表面不易酸洗現象，提高了鋼絲的表面質量。
  3. Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating

    箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。
  4. Abstract : to analyze the temperature of the ladle completely and control it reasonably, the temperature drop behaviors of the molten steel in the ladle under various conditions were studied through establishing a proper mathematical model. the results provide a theoretical basis for reducing the temperature drop and decreasing the tapping temperature of the molten steel in the converter ， and for formulating proper temperature system of the liquid steel

    文摘:為全面分析，併合理控制鋼包溫度，通過建立合理的數學模型，對鋼包熱行為進行模擬，分析了不同情況下鋼液的溫度下降行為.為減少鋼液溫降、降低出鋼溫度、合理制定鋼包溫度制度提供了一定的依據
  5. We detect the degree of oil pollution on line. at the same time we analyzed the eroded and polluted procedure of the wall of steel piping and found the most effective chemical rinsing technics of degreasing, pickling, passive and desiccation procedure

    該裝置全方位控制污染源，合理有效地控制沖洗液的溫度、壓力、流量，在檢測方法上使用了油污染度檢測儀在線檢測。同時分析鋼管內表面的腐蝕和污染過程，找到了脫脂、酸洗、鈍化及乾燥處理這一最有效的化學清洗工藝。
分享友人
分享到 Line

分享到臉書