鋼筋比 的英文怎麼說
中文拼音 [gāngjīnbǐ]
鋼筋比
英文
reinforcement ratio-
Under kinds of conditions, these stresses, strains and their development of concrete, steel, and angle iron were shown. during the whole process, the rate of sharing the loading for the angle iron was also indicated
給出了各種情況下混凝土、鋼筋和角鋼的應力應變值及其發展變化情況；給出了各種情況下，角鋼在加固過程中承擔荷載的比率。It can be seen from the results that the control beam had good plastic property in the static failure experiment after two million fatigue loading circles. all specimens with corroded main bars were failure under the fatigue loads within one million fatigue circles. fatigue lifespan of reinforced concrete beam was sharply shortened after main bars corroded in it and the beam was destroyed bristly without any prediction
試驗結果表明，振動測試不能夠對銹蝕鋼筋混凝土梁的疲勞破壞做出可靠的預測;對比梁在經過200萬次疲勞循環加載后的靜力試驗中仍表現出良好的延性破壞特徵;銹蝕梁在100萬次疲勞循環內均因主筋疲勞斷裂而破壞;主筋銹蝕使得梁的疲勞壽命急劇縮短;梁發生脆性破壞而沒有徵兆。For reinforcement concrete corbel with the shear span to depth ratio ( a / ho ) less than 1, has its performance of mechanics that is close to cantilever deep beams, it is an important kind of components in architectural structure which sustains roof trusses, brackets, tray " beams, frame " beams, wall " beams and crane " beams
剪跨比a h _ 0 1的短鋼筋混凝土牛腿，其受力性能接近於懸臂深梁，在建築結構中是支承屋架、屋面梁、托架、托架梁、框架梁、墻梁和吊車梁等的重要構件。Based on the past results, seismic behavior of r. c. frame structure with special - shaped column is studied, according to the members to the structure in sequence in this paper. the main contents are as follows aspects : first of all, aiming at the characteristics of special - shaped column, various control parameters including allowable value of drift angle, axial load ratio etc, are studied
本文在前人研究成果的基礎之上，就鋼筋混凝土異形柱框架結構的抗震性能，按照從構件到結構的順序展開研究，主要內容如下：第一，針對異形柱的特點，對影響結構抗震性能的主要參數，如層間位移角、軸壓比等進行研究。4. the relation between re - bars strains and cycle index n is obvious. the larger the is, the shorter the n is, and the relation of them is inverse ratio
（ 4 ）鋼筋應變與試件梁的循環次數n之間有規律性，應變越大，疲勞壽命越短，兩者成反比關系。Secondly, this paper made some theoretic researches on its engineering classfication and applicable scope for this technology ; then combining with project example, this paper carried out scheme design for this technology, and compared some different kinds of underpinning scheme and node and structure design, and put forward the method of " reinforcce steel bar through column " to build pile cap beam, " resistant bend and shear anchored reinforce steel bar " to strengthen column consolidation effect, and the method of " steel plate hoop " to build reinforcing bar connection of the foundation beam, etc. in the process of the consturction scheme research and implement, this paper synthetically elaborated the organizaton for project construction, put forward the construction technical measure of specific aim on the artificial pile, and pile cap beam, and underground adding layer and structure stabilization, and overall structure stabilization and so on. for this project, adopt reinforcing bar concrete to brace hole wall to ensure the safety of engineering in the artificial pile construction, use flexible connection catch to make the cage hoisting easier to simplify the construction process, use the method of earthwork statified symmetrical balance in the process of underground adding layer excavation
本文首先對于基礎托換與結構加固技術的目的和意義、國內外發展狀況進行了綜合闡述；其次對該項技術工程分類及適應范圍進行了理論上的分析研究；然後結合工程實例對該項技術進行了方案設計，對比幾種不同的托換方案和節點及構造設計，提出了「通筋穿柱法」做承臺梁， 「抗彎抗剪錨筋法」強化柱加固效果， 「鋼板箍法」做地基梁鋼筋連接點等多項技術；在施工方案的研究和實施過程中，對于工程施工組織進行綜合闡述，並就人工挖孔樁、承臺梁、地下加層及結構加固、整體結構穩定等專項施工方案提出有針對性的施工技術措施，人工挖孔樁施工採用鋼筋砼護壁確保挖孔樁的安全成型，使用柔性連接鉤進行鋼筋籠吊裝簡化施工工序；承臺梁施工採用梁主筋橫穿柱身化學膠錨固等；地下加層綜合施工技術採用土方分層對稱平衡開挖，分段挖土做筏基結構自穩等；最後對于該工程實施后的效果分析，說明該項綜合施工技術的可行性。This paper focuses on the research of the stress mechanism of the ribbed shell structure in statics, dynamics and under the explosive load on the basis of the engineering practice of cave depot of single aircraft. in this paper, according to the classical shell theories, the basic differential equilibrium of the ribbed shell structure and the finite element analysis of 3d rippled plate are established, in which the function of annular ribs reinforcement bars and 3d ripped steel plates are distributed in the range of the steel, and the functions along the longitude direction of tension, bending, and torsion are neglected ; applied with dynamic analytical theory, the dynamic model of ribbed shell structure and the analytical theory model of elastic - plastic are set up ; the triangle series method is used to solve the displacement and stress under the distributed load and the concentrated load of the ribbed shell structure
本文以軍用機場地面單機掩蔽庫工程建設為工程背景，首次對內襯三維波紋鋼板混凝土拱型復合結構的受力機理進行了靜力、動力和爆炸荷載的分析研究。根據將橫肋、鋼筋及三維波紋鋼板的作用均勻分佈在殼體范圍內的情況，忽略橫肋、鋼筋及三維波紋鋼板沿殼體母線方向的抗拉、抗彎及其抗扭作用，首次推導出了內襯三維波紋鋼板混凝土殼體的微分平衡方程，建立了有限元計算模型，並採用三角函數法，求解了三維波紋鋼板混凝土拱型復合結構在分佈荷載和集中荷載作用下的位移響應和應力響應，並與普通殼體進行了比較。This result has practical significance. in this paper ' s theoretical section, base on current shrinkage and creep calculational methods, analysis to the experiment project and tall building structure examples were made, and then the influence of shrinkage and creep to structure stress was put into discussion ; moreover, an fea program was compi led to calculate shrinkage and creep strain considering construction process, and through a tall building instance, the influence to tall frame structure stress was analyzed
本文的理論部分在現有收縮徐變計算方法的基礎上對本試驗工程和高層建築結構進行了算例分析，通過與彈性計算值的對比，討論了收縮徐變對結構內力的影響，以及計算收縮徐變時是否考慮鋼筋和施工過程對結果的影響；本文還編制了考慮施工過程收縮徐變的有限元程序，並進行了算例分析。This paper analyses the stress and deformation of the two lining structure types of the surge shaft surrounded with crush rock under the action of high water pressure by using fem, compares the two lining types ' s merits and demerits in stress, deformation, fracture state, the combining bearing of surrounding rock and lining structure, the safety and economics
本文針對圍巖條件比較破碎，裂隙發育的調壓井洞室結構，就兩種襯砌結構型式分別進行了高水頭作用下的有限元數值模擬，從調壓井襯砌結構選型角度分析對比了兩種襯砌結構型式在圍巖及襯砌結構應力與變形、襯砌結構鋼筋混凝土開裂、圍巖與襯砌結構聯合承載、結構安全儲備、經濟等方面的優劣。The steel bar produced in our country is not good as that produced by steel developed country in terms of mechanic character, dimensional accuracy etc. it is important to produce high performance and dimensional accuracy steel bar for the marketplace and link orbit of international marketplace
我國生產的鋼筋在機械性能、產品尺寸精度等與鋼鐵發達國家相比還存在著一定的差距，為了滿足市場需求，盡快與國際接軌，生產出機械性能好、尺寸精度高的鋼筋顯得十分重要。As a whole, the research work of this dissertation can be summarized follows : 1. in accordance with my design patent, namely, reinforced earth retaining wall of r c net, and based on the analysis of the work mechanism, failure pattern, bearing capacity and stability of the reinforced earth, a new concept is expounded, namely, the reinforced earth wall which is thought of as a compound structure increase not only c but also ~ in comparison with non - reinforced earth. some bearing capacity formula are first introduced under the circumstances that the reinforced earth wall fails because of the breakage of material or inadequate cohesion between reinforcements and soil
歸納起來，具體的研究和所獲得的一些重要成果如下： 1 、結合本人的設計專利? 「鋼筋混凝土網格式加筋擋墻」及工程實踐，在對加筋土的加筋機理、破壞模式、承載力和穩定性等方面進行深入分析的基礎上，提出了一個新概念，即經過加筋后的土體作為復合結構與原土體相比，不僅提高了內聚力，而且也提高內摩擦角；並在此前提下首次導出拉力破壞和粘著破壞兩種情形下的承載力公式，然後進行了穩定性分析。Working carefully in fast - flowing eddies created by crumpled steel and concrete, divers with only a foot of visibility had located some of the vehicles that were hurled into the river when the 40 - year - old bridge gave way during wednesday ' s evening rush hour in minneapolis
星期三傍晚下班交通高峰時期，密西西比河上方一座年逾40的橋轟然倒塌，斷橋的鋼筋混凝土掉入水中激起很多旋渦，水下救生員在能見度只有一英尺的水中經過認真摸索找到了一些被捲入急流旋渦中的汽車的位置Based on the pseudo - static experimental results of nine abnormal joints, the damage process of abnormal joint is divided into four stages of original crack, entire crack, ultimate state and failure, the effect of axial force ratio, stirrup ratio and height of column section on seismic behavior of abnormal joint are discussed, the conclusion that anti - shear capacity of abnormal joint are studied in entire crack state by studying the minor core of abnormal joint is made, the calculating formula for anti - shear capacity of abnormal joint is proposed with a view to asymmetry in stirrup yield
摘要根據9個鋼筋混凝土框架異型節點試件的擬靜力試驗結果，指出異型節點受力過程分為初裂、通裂、極限和破壞4個階段；討論了軸壓比、節點核芯配箍率、柱截面高度變化對異型節點抗剪性能的影響；提出應考慮節點核芯區箍筋屈服的不均勻性並在通裂狀態下以「小核芯」為分析單元來研究此類節點抗剪承載力的建議；最終給出了異型節點抗剪承載力的計算公式。While many theories concerning damage forecasting were put foreword, a different model of damage forecasting based on fuzzy probability will be presented in this paper. and it is reasonable to describe a variable like weight coefficient with fuzzy theory. in the end, the validity of the model is demonstrated well in the applications of one - storied brick bent frame column factories, one - storied reinforced concrete column factories, multistory masonry buildings
國內外不少專家學者或研究單位先後提出了各種震害預測方法，本文在此基礎上，利用模糊理論，提出了模糊概率的震害預測模型，其模型能夠把兩類不確定性（一類是隨機上的，另一類是模糊上的）有機結合起來，而且對于權重這樣一個充滿著模糊性的變量，用模糊語言來處理是非常合理的；並應用於對單層磚排架柱廠房、單層鋼筋混凝土柱廠房以及多層磚房的震害預測，實踐證明此方法是比較精確的。Products function : put our “ sun shine ” brand carbon steel fiber evenly seep into concrete to form steel fiber reinforced concrete and it can decrease the thickness of reinforced concrete by half, it not only shorten the project time, save the material and manpower expense, bring distinct economic benefit, but also increase the performance of crack resistance, percussion resistance, tensile strength, bend resistance. scosspr resostamce amd wear resistance of the reinforced base materials. if the weight ratio of 2 % steel fiber seep into the concrete, it can solve the brittleness problem of the concrete, in the condition of 60 % ralative air humidity, after 21days air - dry, even 520 days air - dry, it ' s difficult to find any crack by eyesight, the bend resistance for the steel fiber concrete is 140 times stronger than the concrete without steel fiber, the capability of impact resistance increase 10 times
產品功能：將本公司「雙興」牌碳鋼纖維系列產品均勻地摻入混凝土中，形成鋼纖維增強混凝土，可使工程中鋼筋混凝土的施工厚度降低一半，不僅縮短了施工工期，節省了材料和人工費用，帶來顯著的經濟效益，且增強了基體的抗裂、抗沖擊、抗彎、抗剪、耐磨擦等性能，如摻入本公司2 %鋼纖維的混凝土，不僅解決了混凝土的脆性問題，在空氣相對濕度60 %的條件下風干21天後，甚至在風干520天，肉眼很難發現裂縫，摻入鋼纖維后的增強混凝土比不摻鋼纖維的混凝土抗彎強度提高140倍，耐沖擊荷載提高10倍。The influence of such parameters as axial load index, aspect ratio and percentages of lateral reinforcement, on seismic performance of reinforced concrete frame column in hong kong and analyses the distribution relationships of flexural deformation, shear deformation and slippage of longitudinal reinforcement in joint zone
根據試驗結果，討論了軸壓比、配箍率、剪跨比等參數對其抗震性能的影響，分析了水平荷載作用時塑性鉸區的彎曲變形、剪切變形和縱向鋼筋粘結滑移變形所產生的位移在框架柱總水平側移中所佔的比例及其變化規律。The author redesigned the common concrete beams and carried out a comparative analysis to the existing beams according to the specification for design of reinforced concrete and prestressed concrete highway bridges and culverts ( jtj023 - 85 ), the specification for design of reinforced concrete and prestressed concrete highway bridges and culverts ( informal version for advices ) and relevant rules of its matching stipulations, light aggregate concrete bridge technology stipulations ( ( informal version for advices ) and on the basis of prestressed concrete theory. the thesis emphasized on the research of the variation of the concrete, prestressing tendon quantities, their spans, beams " height and their rigidity of both the designed beams and the existing beams, and obtained the quantitative results from above research
採用hslc置換梁體中的普通混凝土，並運用預應力混凝土理論，依據《公路鋼筋混凝土及預應力混凝土橋涵設計規范》 （ jtj023 - 85 ） ， 《公路鋼筋混凝土及預應力混凝土橋涵設計規范》 （徵求意見稿）和與之配套編制的《輕骨料混凝土橋梁技術規程》 （徵求意見稿）的有關規定，對上述普通混凝土梁進行了重新設計並與既有梁進行了對比分析，得出了設計梁與既有梁在混凝土及預應力筋用量、跨度、梁高以及剛度等方面的變化情況，得到了定量結果。Present methods generally based on the statistics of earthquake damage, expert experiences, theory analysis and experimental researches have obvious advantages, disadvantages and certain scopes of application ; ( 2 ) different prediction methods should be adopted against different building conditions, sites, intensity and experiences etc to predict earthquake damage of buildings for prospective accuracy, dependability and availability ; ( 3 ) earthquake damage matrix, which is the foundation of earthquake damage prediction, of 7 kinds of building in the urban areas of zhangzhou city under intensity 6 to 9 has been set up. the damage conditions of different buildings under different intensity are as followings : all kinds of structures are basically intact under intensity 6 ; the reinforced concrete structures are basically intact under intensity 7, but other kinds of structures are destroyed slightly ; the reinforced concrete structures are still basically intact while other kinds of structures are destroyed intermediately under intensity 8 ; the reinforced concrete structures are destroyed slightly, single - story factories and open houses are destroyed intermediately and other kinds of structures are destroyed seriously under intensity 9 ; ( 4 ) the results of earthquake damage predicting of buildings embody the damage when earthquake happens in the future. thus, further identifications and reinforcements should be considered to buildings that will be destroyed intermediately or more under the earthquake with 10 % exceeding probability in future 50 years ; ( 5 ) the direct economic losses caused by damage of buildings resting with the area, structural type, intensity and damage of all kinds of buildings are the main part of the losses of the city in an earthquake ; ( 6 ) the direct economic losses increased progressively toward high intensity by 2 or 3 times
基於上述研究，得出的主要結論有：建築物震害預測是一個模糊的、系統的、復雜的問題，現有的方法很多一般都是以震害統計規律、專家經驗、理論分析和試驗研究為依據，有其自身的優缺點和一定的適用范圍；應針對不同的建築物條件、場地條件、地震強度和已有經驗等，採用不同的預測方法進行建築物震害預測，以使預測結果達到預期的精確性、可靠性和可操作性；建立了漳州市區7類建築物在6度9度地震作用下的震害矩陣，成為指導抗震防災的重要依據，各類結構的震害情況表現為： 6度地震作用下各類建築物基本完好； 7度地震作用下除鋼筋混凝土結構基本完好外其餘以建築輕微破壞為主； 8度地震作用下鋼筋混凝土結構仍以基本完好為主而其餘建築以中等破壞為主； 9度地震作用下鋼筋混凝土結構以輕微破壞為主，單層工業廠房和空曠房屋以中等破壞為主，其餘建築以嚴重破壞為主；建築物的震害預測結果體現了未來地震來臨時的震害程度，在編制漳州市區抗震防災規劃時，對于遭遇50年超越概率10的地震影響發生中等以上破壞的建築物應考慮進行抗震鑒定和加固；由建築物的破壞所造成的直接經濟損失是城市地震經濟損失的主要部分，重慶大學碩士學位論文中文摘要其主要與建築物總面積、結構類型、地震烈度和各類建築物的震害程度有關;不同烈度造成的直接經濟損失按2一3倍向高烈度方向遞增，漳州市區直接經濟損失由6度至9度的比例關系為1 : 2 . 8 : 8 . 6 : 22 . 8 ;遭遇基本地震設防烈度（ 7度）時，漳州市區直接經濟損失約4 . 5億元，無家可歸人員約40000人，且以磚木結構和多層磚混結構的震害損失最大;地震造成的人員傷亡主要與建築物倒塌及嚴重破壞的程度和總面積以及震時的建築物室內人數密切相關，地震時無家可歸人員主要與住宅倒塌、嚴重破壞及中等破壞的程度和總面積以及城市人均居住面積密切相關。Abstract : it is a difficult problem to arrange a lot of deformed bars in a narrow section. in foreign codes, it is solved with abreast - arranging deformed bars, but there not be definite answer about influence that the abreast - arranging deformed barsto bearing capacity. in our country, the research about abreast - arranged deformed bars began from the first 1980s. some achievements have been gained from studies about anchor performance. but study about beams bearing capacity and rigidity is not enough. the experiments of 10 beams using abreast - arranged deformed bars and 3 contrast ones are done. the influence that the abreast - arranging deformed bars to bearing capacity of beams is analyzed. three points of division loading have been adopted. the results prove that the bearing capacity of beams decrease by using abreast - arranged deformed bars at a degree from 10 % to 15 %. through statistical analysis, format on bearing capacity of abreast - arranged beams is recommended and reliability of format is analyzed
文摘:在較小截面內單根排列鋼筋比較困難，國外規范大都採用並筋解決，但對並筋后對承載力的影響未作明確規定，我國並筋梁的承載力和剛度研究較少.通過對10根並筋梁和3根對照梁的受彎承載力的試驗，分析並筋對梁的受彎承載力的影響，試驗採用三分點加載，結果表明，與對照梁相比，並筋梁的受彎承載力有所降低，降幅在10 % 15 %之間，通過統計分析，給出了並筋梁受彎承載力的建議公式，並對建議公式進行了可靠度分析It is a difficult problem to arrange a lot of deformed bars in a narrow section. in foreign codes, it is solved with abreast - arranging deformed bars, but there not be definite answer about influence that the abreast - arranging deformed barsto bearing capacity. in our country, the research about abreast - arranged deformed bars began from the first 1980s. some achievements have been gained from studies about anchor performance. but study about beams bearing capacity and rigidity is not enough. the experiments of 10 beams using abreast - arranged deformed bars and 3 contrast ones are done. the influence that the abreast - arranging deformed bars to bearing capacity of beams is analyzed. three points of division loading have been adopted. the results prove that the bearing capacity of beams decrease by using abreast - arranged deformed bars at a degree from 10 % to 15 %. through statistical analysis, format on bearing capacity of abreast - arranged beams is recommended and reliability of format is analyzed
在較小截面內單根排列鋼筋比較困難，國外規范大都採用並筋解決，但對並筋后對承載力的影響未作明確規定，我國並筋梁的承載力和剛度研究較少.通過對10根並筋梁和3根對照梁的受彎承載力的試驗，分析並筋對梁的受彎承載力的影響，試驗採用三分點加載，結果表明，與對照梁相比，並筋梁的受彎承載力有所降低，降幅在10 % 15 %之間，通過統計分析，給出了並筋梁受彎承載力的建議公式，並對建議公式進行了可靠度分析分享友人