錐形分離器 的英文怎麼說

中文拼音 [zhuīxíngfēnlíqì]
錐形分離器 英文
cone separator
  • 錐 : Ⅰ名詞1. （錐子） awl2. （似錐物） awl-shaped things 3. （錐體） cone Ⅱ動詞（鉆） drill; bore
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 離 : Ⅰ動詞1 （離開） leave; part from; be away from; separate 2 （背離） go against 3 （缺少） dispens...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 錐形 : [機械工程] taper; cone; cone-shape
  1. Using processed march cylinder, tapered circular mould, u - shaped instrument, l - shaped concrete fluidity instrument and some other testing instruments, and after research and study to physical and chemical property of various raw material. systematic tests have been carried out in respect of consistency between cement and additive, concrete fluidity, concrete filling - up - space and penetration capability and concrete anti - segregation property, basing on prudent and careful analysis to results of 34 - time tests a nd more than 500 data, and with utilization of combined additive, we finally conclude the proper mix design range for the self - densifying high performance concrete with ideal working performance at all respects

    通過加工的march筒、截錐形圓模、 u型儀、 l型混凝土流動儀等實驗儀器以及對各種原材料的物理及化學性能展開詳盡的調查研究，進行了多種材料下的水泥與外加劑相容性、混凝土的流動性、混凝土的填充性和鋼筋通過性、混凝土的抗離析性等系統試驗，在對34組試驗、 500多個數據的詳細認真分析的基礎上，利用復合后的外加劑，得出各項工作性能均較佳的自密實混凝土所用原材料比例范圍。
  2. ( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )

    研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。
  3. Clk - proliferation cyclone applicable to the collection of non - fiber drying of granular dust is the main characteristics of a conical dongshen, thus reducing the dust since the dongshen gas exports to the centre to short - circuit the possibility and install a conical reflector screen to prevent the two air separation will have to roll up the dust down, brought out by the increased flow, thereby enhancing the efficiency of dust

    Clk擴散式旋風除塵器，適用於捕集乾燥的非纖維性的顆粒狀粉塵，主要特點是筒身呈圓錐形，因而減少了含塵氣體自筒身中心短路到出口去的可能性，並裝有圓錐形的反射屏，防止兩次氣流將已經分離下來的粉塵重新捲起，被上升氣流帶出，因而提高了除塵效率。
  4. Domestic and abroad standard and test information of alimak co. for braking distance of antifalling safety device of construction hoist are analyzed. the writers study the application and inspection situation of safety device in our country and put forward a suggestion of reasonable range of braking distance for safety device with gear cone drum

    本文分析了有關施工升降機防墜安全器制動距離的國內外標準條文和alimak公司的試驗資料，結合我國施工升降機防墜安全器的應用和檢測情況，提出了修改齒輪錐鼓形防墜安全器制動距離合格範圍的建議。
分享友人
分享到 Line

分享到臉書