錐形棒 的英文怎麼說

中文拼音 [zhuīxíngbàng]
錐形棒 英文
tapered rod
  • : Ⅰ名詞1. (錐子) awl2. (似錐物) awl-shaped things 3. (錐體) cone Ⅱ動詞(鉆) drill; bore
  • : Ⅰ名詞(棍子) stick; staff; club; cudgel Ⅱ形容詞[口語] (強; 高; 好) strong; excellent; good
  • 錐形 : [機械工程] taper; cone; cone-shape
  1. The ultrastructure of the merozoites of eimeria tenellawas observed and discribed. the pellicle consist of two layer membranes, the outer membrane was a continous covering enclosing the whole merozoites, while the inner pellicular complex is interrupted at the anterior and the micropore, and thicken to form the polar ring and micropore. there are 24 microtubules under the pellicle of the merozoite which originated from the polar ring, all of them are connected with the polar ring, and extend alongside the inner pellicular complex to the middle of the merozoite. the head of the merozoite consists of a conoid, an apical vesicule and polar ring. the conoid is a hollow truncated cone. the conoid and spical vesicule can stretch and contract. there are three or more rhoptry and a lot of micronemes. the nucleus has nucleolus. and two layer membranes

    利用透射電鏡對柔嫩艾美耳球蟲裂殖子的超微結構進行了觀察描述.柔嫩艾美耳球蟲裂殖子的表膜由外膜和內膜復合體兩層組成,外膜連續,內膜復合體在頭部斷開成極環,在其它部位斷開成微孔;裂殖子的膜下微管24根,起始於極環,向後延伸至細胞核處;裂殖子的頭部由頂泡、體和極環組成,體和頂泡可以伸縮;柔嫩艾美耳球蟲裂殖子狀體3個以上,微線數量很多,二者都由電子緻密的結構組成;細胞核位於裂殖子的中後部,外被雙層膜,有電子緻密的核仁和染色質
  2. Abstract : this paper analyzes theoretically the effect of the reversed cone angle and length of the plug on restraint and elimination to the distortion of the internal spiral ribs, and put forth the design methods of the plug in drawing rifled tube

    文摘:從理論上分析了芯角和芯長度對內螺旋凸筋狀畸變的抑制和消除作用,提出了採用倒等螺距芯拉拔內螺紋管時芯幾何參數的設計方法。
  3. In order to obtain faster response times there is a version with a tapered immersion shaft

    為了縮短響應的時間,我們研發了
  4. The calculation results show that the stress distributing of the plug drawing tube is different because of different dies, the drawing force and pulling force are lager in arc die and the diameter and wall thickness are closer to the designing value in cone die

    計算結果表明,不同的模具,芯拔管的應力分佈不同,弧模成型的拔制力與芯后拉力較大,模成型后鋼管的直徑與壁厚更接近設計值。
  5. Hydrostatic extrusion process of rods through conical die by element - free method

    材通過模靜液擠壓成的無網格法分析
分享友人