錐形量器 的英文怎麼說
中文拼音 [zhuīxíngliángqì]
錐形量器
英文
conical graduate-
The study is imitating subulate tool penterite armor fabric by method of test for puncture of paperboard and corrugated fiberboard, and to ascertain the laver of armor fabric for absorb energy and arrestment, and any difference angle to compare the rank of defying ball, for understanding the sharp to the rank of annor fabric defy penterite energy, and penterite deep, the lose energy relation of sharp
摘要本研究是以沖孔強度試驗機測試，模擬尖錐利器攻擊穿刺防彈衣，且對于防彈衣層數間的阻抗作用及能量吸收的情形，並對各種不同角度的抗彈織物疊層排列作相互比較，進而?解尖錐對防彈衣的抗穿透層數之能量及穿透深度、錐度之能量耗損之間關系。The result shows that the quenching inductor with wimble magnet inlaid is adaptable for this technique, and the vertical quenching machine can be used in mass production
結果表明，帶錐角鑲嵌導磁體的圈式感應器，其有效圈高度、錐角和內徑的合理匹配可以滿足淬硬層形態的要求，採用立式淬火機床連續淬火可以大批量生產合格的半軸。( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )
研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。Standard test method to measure viscosity by tapered bearing simulator at high temperature and high shear rate
在高溫和高剪切率下用錐形承載模擬器測量粘度的標準試驗方法Standard test method for measuring viscosity at high shear rate and high temperature by tapered bearing simulator
用錐形承載模擬器在高剪切率和高溫下測量粘度的標準試驗方法Round general use light gauge metal containers - nominal diameters for cylindrical and tapered cans up to 10 000 ml capacity
通用圓形小量規金屬容器.最大容量為10 000 ml的圓柱形罐和圓錐形罐的標稱直徑分享友人