錐頭電極 的英文怎麼說
中文拼音 [zhuītóudiànjí]
錐頭電極
英文
truncated tip electrode-
The ultrastructure of the merozoites of eimeria tenellawas observed and discribed. the pellicle consist of two layer membranes, the outer membrane was a continous covering enclosing the whole merozoites, while the inner pellicular complex is interrupted at the anterior and the micropore, and thicken to form the polar ring and micropore. there are 24 microtubules under the pellicle of the merozoite which originated from the polar ring, all of them are connected with the polar ring, and extend alongside the inner pellicular complex to the middle of the merozoite. the head of the merozoite consists of a conoid, an apical vesicule and polar ring. the conoid is a hollow truncated cone. the conoid and spical vesicule can stretch and contract. there are three or more rhoptry and a lot of micronemes. the nucleus has nucleolus. and two layer membranes
利用透射電鏡對柔嫩艾美耳球蟲裂殖子的超微結構進行了觀察描述.柔嫩艾美耳球蟲裂殖子的表膜由外膜和內膜復合體兩層組成,外膜連續,內膜復合體在頭部斷開形成極環,在其它部位斷開形成微孔;裂殖子的膜下微管24根,起始於極環,向後延伸至細胞核處;裂殖子的頭部由頂泡、錐體和極環組成,錐體和頂泡可以伸縮;柔嫩艾美耳球蟲裂殖子棒狀體3個以上,微線數量很多,二者都由電子緻密的結構組成;細胞核位於裂殖子的中後部,外被雙層膜,有電子緻密的核仁和染色質Resistance spot welding. electrode holders. part 1 : tapper fixing 1 : 10
電阻點焊.電極夾頭.第1部分:固定錐度為1 : 10Specification for resistance spot welding - electrode holders - morse taper fixing
點焊設備規程.電極夾具.第2部分:莫氏錐形接頭Resistance spot welding - electrode adaptors, male taper 1 : 10 - part 2 : parallel shank fixing for end - thrust electrodes iso 5183 - 2 : 2000 ; german version en iso 5183 - 2 : 2002
電阻點焊.外錐度1 : 10電極接頭.第2部分:軸端推力電極Resistance welding equipment - electrode adaptors, male taper 1 : 10 - parallel shank fixing for end - thrust electrodes
電阻焊設備.外錐度1 : 10電極接頭.端推力電極用平行柄接頭Resistance spot welding - electrode adaptors, male taper 1 : 10 - part 2 : parallel shank fixing for end - thrust electrodes
電阻點焊.外錐度1 : 10的電極夾頭座.第2部分:端推力電極用直柄接頭1 10 electric resistance welding. straight resistance spot welding electrodes with caps, male taper fits and male caps. sizes and tolerances taper 1 10
電阻焊接.帶電極帽外錐度配合和凸頭電極帽的直點焊電極.尺寸和公差Resistance spot welding. electrode holders. part 2 : morse taper fixing
電阻點焊.電極夾頭.第2部分:莫氏錐度固定Specification for resistance spot welding - electrode holders - taper fixing 1 : 10
點焊設備規程.電極夾具.第1部分:錐形接頭錐度1 : 10Resistance spot welding - electrode adaptors, female taper 1 : 10
電阻點焊.內錐度1 : 10的電極接頭Resistance welding equipment - electrode adaptors, male taper 1 : 10 - part 1 : conical fixing, taper 1 : 10
電阻焊接設備.電極接頭外錐度1 : 10 .第1部分:圓錐形接頭錐度1 : 10分享友人