錘和鋼 的英文怎麼說

中文拼音 [chuíhégāng]
錘和鋼 英文
hammer and steel
  • 錘 : Ⅰ名詞1 （一種古代兵器） a metal ball with a handle or chain used as weapon; mace2 （秤坨; 像錘的...
  • 和 : 和動詞（在粉狀物中加液體攪拌或揉弄使有黏性） mix （powder） with water, etc. : 和點兒灰泥 prepare some plaster
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  1. Thanks to the most advanced steel composition purifying technology in the world, we specialize in producing wear resistant, high temperature resistant and corrosion resistant equipment fittings for tool & mould steel materials ; also we are the professional producer of imported muller hammers, crusher hammers and scale boards

    擁有國際先進的新型鋼鐵組織凈化技術，重點生產工具模具鋼材料和抗磨、耐熱、耐腐蝕設備配件，是進口細碎機、破碎機錘頭、襯板的專業生產商。
  2. Main product : tungsten carbide powder, roll ring, anvil and cylinder, mining button bit, dies nib for various application : cold heading dies, drawing dies and non - magnetic carbide dies. all of the products mentioned above could be offered in blank or finishing product

    公司主要產品有：碳化鎢粉硬質合金輥環頂錘和壓缸冷鐓模無磁合金礦山柱拉絲拉管模棒材板材非標模具及硬質合金精密加工產品等，廣泛應用於鋼鐵標準件金剛石粉末冶金石油礦山磁性材料機械加工電子等行業。
  3. Steel die forgings - tolerances on dimensions - drop and vertical press forgings

    鋼模鍛.公差和尺寸.落錘或垂直壓力鍛造
  4. Abstract : based on the analysis of pipe ramming procedure, thi s paper presented the method calculating the ramming resistance force according to the results of strata pressure and dynamic probing, and the method calculating displacement, li mit length of rammed pipe and max. pressure inside pipe according to wave dynami cs

    文摘:分析了夯管錘夯入鋼管的過程，提出了依據地層壓力和動力觸探結果計算夯入鋼管阻力的方法；還提出了應用波動力學計算夯入鋼管位移、極限鋼管夯入長度及鋼管內最大壓應力的方法。
  5. Steel die forgings - tolerances on dimensions - part 1 : drop and vertical press forgings ; german version en 10243 - 1 : 1999, corrigenda to din en 10243 - 1 : 2000 - 06 ; german version en 10243 - 1 : 1999 ac : 2005

    鋼模鍛件.尺寸公差.第1部分:落錘鍛造件和垂直壓力鍛
  6. The outputs of tests on the thin plate under different inputs have been investigated for testifying the system. different solutions have been compared according to the frequency - spectrum characters and structure modal parameters. it is indicated that the solutions in this paper are consistent with the solution of the fea methods

    以薄鋼板為實例，探討了不同激勵條件下，包括正弦穩態激勵、正弦慢掃描、單次錘擊和隨機錘擊激勵，薄鋼板振動系統的響應情況，以頻譜特性和模態參數為參考，將各種方法的求解結果作了比較，結果表明：本系統得出的結果與有限元解具有一致性。
  7. Steel die forgings - tolerances on dimensions - part 1 : drop and vertical press forgings ; german version en 10243 - 1 : 1999

    鋼模鍛件.尺寸公差.第1部分:落錘和立式壓力機鍛件
  8. Then model experimental on the steel frame structure, experiment uses random knock and single knock separately on the steel frame structure through a force hammer. we can gained the data of experiment using transducers and the data acquisition system and post treatment of the data

    然後，對該鋼框架模型進行模態試驗，試驗通過力錘分別對鋼框架進行隨機敲擊和單次敲擊，通過傳感器和數據採集系統得到結構的試驗數據，再對試驗數據進行后處理。
分享友人
分享到 Line

分享到臉書